Just bought an IPhone4 and can't connect to network. It asks me for password and I correctly typed in password. It said invalid. I reset the user password on my DIR 615 Dlink router, rebooted and same thing. I connect with my laptop wireless without any problems
View 10 Replies
I seem to be struggling to connect more than 4 cameras to my (ISP-supplied) modem/router by Netgear CGD24N via WPS. I'm on my 5th camera now (already have 3x 930L and 1x 942L) but the newest 942L just won't connect to the network at the moment and there's definitely no faults here as I swapped cameras today at the local retailer (and got an A3 942L!).I've even tried connecting the camera to my wireless extender (Netgear WN3000RP) but no luck there.
So far it has only worked twice for short periods of time (enough for me to configure the cameras) but since then I can't actually get it working. I've got a couple of spare wireless routers lying around too and should be receiving a DIR-600 soon (from the Netgear promotion in Australia) which could be useful?
Camera set up with the Beta Mac wizard connected via ethernet on Airport base. Wireless security WPA2 Personal. Using DHCP. AirPort Utility 5.5.2, OSX 10.6.6.I can see the cam with the myDlink Lite iPhone (4) App when I am in my house with my wireless network. When I am out, away from my network, the App can't connect to the cam, tells me to check my network settings. I did the wps way and added the cam in the airport base utility *Access Control* tab but still doesn't work. Checked in the cam web page settings, can't figure out what the Pre-Shared Key is and where I get it/set it up in the airport utility...
View 1 Replies View RelatedI got my protected stuff set up but every time i try to connect my laptop wirelessly i get errors. I select the wireless network and it says i need a pin.I goto advanced on the router setup ans wifi protected setup and use the pin there and I get the following error
"Windows cannot get the network settings from the router"
I've bought a D-Link DIR-615 Wireless N Router. I have a SONY BDP-S370 Blu-ray player with a LAN socket.
I have my Dell Inspiron laptop working on Windows 7 (with LAN socket and wireless N card). I have a HTC Desire phone. I use my HTC Desire as a WI-Fi hotspot to connect to the internet.
I would like to plug the router to the Blu-ray player so that I can use the internet connection broadcasted by my phone. I would also like to be able to access the contents of my laptop on the Blu-ray player through the wireless router.
I downloaded the MAC setup Utility(BETA) and it can't find the camera.The camera is connected via Ethernet-Light on the front under the lens is green (blinks sometimes)First thing I noticed wrong was the setup utility asks if the light on the side of the camera is lit green-there's no light on the side of the camera as far as I can tell. I tried unplugging the camera and hitting the reset button on the back-nothing works.
PC: MAC OSX 10.6.7 (2.2GHz Intel Core 2 Duo/4GB RAM)
Router: Linksys WRT54G Wireless-G Broadband 2.4GHz
Browser: FireFox 4.0.1
I have recently moved and I brought my wireless router with me from my last home. The wireless router is a D-Link DIR-615 Wireless N Router. I reconfigured the router with a new connection name, password and security key. Upon trying to connect to the wireless network once it was fully reconfigured (no problems reconfiguring whatsoever), I was getting the "Windows was unable to connect" message. Since then, I have been able to connect successfully to the network with an iPod Touch, Xbox 360, Playstation 3 and my roommate's laptop. I have tried resetting the router and modem with no success. I can see the wireless network in the available connections list and other networks in my area. I can also connect to the internet through this router manually using an ethernet cable (which I am doing now, to post this message). I submitted my computer's specs using the SysInfo app given at registration.
I will also include an IPCONFIG /ALL as I have seen this requested in other threads like this one. These are the results of that: (note: this was run while connected through the wireless router using an ethernet cable)
Windows IP Configuration
Host Name . . . . . . . . . . . . : Kalmah
Primary Dns Suffix . . . . . . . :
[Code].....
I recently bought a windows laptop running vista to do windows testing on for web development (I use macs normally).I was shocked to find that I can't simply push connect, enter a key and then be connected to our home wireless network... no of course not because it's windows and nothing is easy or practical.Anyhow, before I go on an anti windows rant, I actually need this working.So at home we have a wireless network secured by a 32bit WEP key.On our macs I simply push connect, enter this key and we're away.With my new vista machine I go to Network & Sharing Center -> Connect to a network and click our network.I'm then immediately met with a screen that says "Press the configuration button on your access point". I have no idea what this means.Down the bottom of the screen there is an option that says "I can't find the configuration button... I want to enter the network key or passphrase instead" Which I click.The next screen I click "Enter/Select additional log on information" but this brings up a user name/ password/ login domain screen... I just want to enter my 32 bit key and be connected. I'm using a D-Link DIR-615 wireless router.Also, when I run "ipconfig" in the command prompt I get."Media State....: Media disconnected"
View 1 Replies View RelatedI recently purchased a DIR-815 D-Link router. I've set up my network successfully; my laptop and smart phone are easily able to connect. However my desktop is having issues. My network card detects the wireless network I have set up, however the password is always rejected. I am typing in the correct password. I can get the internet to work on my desktop if I connect the router directly by wire, but I need the wireless to work. My desktop runs Windows 7.
View 3 Replies View RelatedRegion : Spain
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.11 Build 120328 Rel.63398n
ISP : SPAIN MOVISTAR
My TL-MR3040 router identifies correctly my ZTE MF 110 HUSPA USB MODEM but it doesn't connect to my ISP Movistar in Spain This is the Log of the router:
Log Content
before switch modem vid is 0x19d2 pid is 0x0083
Device vendorID: 0x19d2; productID: 0x0083
handle_card start
mobileCmdReq 328 mobileFormatCmd error
[code]....
i got a Dir-615 N300 few days ago...and it took me 2 days to make the wireless network and connect my HP Laptop to it...now my cousin wanted to use my wireless and couldn't...spent like 3 hours trying different things and nothing...
Basicly...she can see my SSID,but when she tries to connect...it doesn't work...it just...loads...it doesn't ask for the password or anything...
A friend told me that i might have to give her acces in some way... I have no idea what i did but it worked for my laptop.
Few Details:
My cousins laptop is an Acer with Xp SP2 i think...(while mine is HP with Windows 7)
Security mode WPA-Personal
Cipher Type: AES
Hardware Version: Hx
Firmware Version: 8.02
btw i did everything on the http link...not the cd...for some reasons the cd didn't work for me
My Dlink DCS-930 camera won't work over 3G. It works fine on my home WiFi network. When on 3G it shows the camera, click it, tries to connect but just keep saying connection timeout.
It used to work over 3G fine, nothing has changed to my network. I've rebooted the camera and router numerous times, it has the latest firmware, but still won't work. I'm logged into my dlink account fine. I have an Apple Time Capsule.
I have a D-Link AIrPLus G DI-524 802.11g/2.4 Ghz Wireless Router and a HP Pavilion dv7 Notebook PC. I cannot seem to connect to the router. I can do so on my Blackbery Curve but my computer tells me "Windows was unable to connect to *****" There was no chance to give the Security Key.
View 9 Replies View RelatedIs it possible to connect the dap-1622 to a hidden network using WPA Radius? I've tried, but didn't succeed. I'm running FW version 1.41. I've tried with older FW versions, and none of them seems to work.
View 1 Replies View RelatedI just upgraded my wireless router to a D-Link DIR-655. I have 2 PCs and a network storage device (D-Link DNS 321) connected via ethernet to the router. I also have an xBox 360 connected wirelessly to the router. The xBox is able to connect to the internet via the router, but it cannot connect to (see) the PC's or the network storage device. It was able to do so with my old wireless router (a Belkin), but it stopped with the DIR-655.
View 4 Replies View RelatedI recently bought a DIR-655 on amazon com, got a good deal. Since I'm old and slo, had issues setting it up, but finally got er dun!I set up a Network all by myself turned on player, did WPS(PBC) on player, and on D-Link. The router and Blu-ray are now friends, however, they are not on speaking terms.Network status on ol Blu- tries to connect then says - Network setting is completed, but cannot connect to the internet, Contact ISP.
View 8 Replies View RelatedI finally managed to set up this DSL modem / router on Sunday to replace my old Billion router. I set it up with DHCP and running on IP 192.168.1.254.Last night, the power tripped, and when everything came up again the entire network was dead - PC's were not getting IP's from DHCP.I connected a known working cable directly from laptop to router and attempted to access 192.168.1.254, nothing.So I reset the router and try again to the default IP 192.168.1.1. Nothing. Tried another PC, nothing.Restart router, try again, nothing. Plugged into my other router and try again, nothing. When I initially got the router I had the same problem until one day it just worked, still no idea why
View 2 Replies View RelatedChanged from D-Link to Netgear router now only one of two computers cannot see the other. Error shows cannot connect to MSHOME network, need administrative approval. Computers are ethernet connected to the router. Have McAffe and both computers are "Trusted" Can do a search with XP and it shows the missing computer but unable to make a connection.
View 5 Replies View RelatedI'm desperately trying to set up my old D-Link DI-524 on my parent's Toshiba laptop...I'm visiting and going thru withdrawals! I've installed it, run the wizard etc but it doesn't work...not even wired. I've tried various cable configurations and I get nothing. Both cables are good and work just fine connected to the modem. I've reset it a few times, upgraded the firmware and still nothing...I'd think I'd at least get it to work hard wired. My laptop can see the network I set up even...but no data transmission. I'm not a wireless expert, but I need to become one fast!
View 3 Replies View RelatedCannot connect network radios after upgrading to latest firmware. Could connect before upgrading firmware but throughput was slow for computers and streaming. Now I can connect computers, but not radios. They connect ok using Belkin and Linksys routers.
View 4 Replies View RelatedI reset my Dlink 615 wireless router. I held down the power and reset for 30 seconds and rebooting the system with the disc. I did change the router name, but believe everything else stayed the same. My desk top is working fine being "hardwired" but nothing wireless will connect.
I did see this time it installed Network Magic which I have since uninstalled and again rebooted the computer system and still cannot get the wireless to work. It shows the network available, but my password for some reason does not take.
I have 3 pieces of hardware:
1. Green Packet DX-230 WiMAX modem with router
2. D-Link DIR-615 ver G2 (from my ISP)
3. D-Link 8 port desktop switch
I previously used the DIR-615 with my high speed broadband connection. However I had to move to a new house and here I can only get WiMAX. I want to...Place the WiMAX modem upstairs to serve as modem and wireless access point Have the DIR-615 function as the main router and firewall (downstairs) Use the switch to connect all the rooms in my house FYI my WiMAX modem has no connection configurations. I just plug it in and it'll connect automatically to the WiMAX signal. It has 2 LAN ports but no WAN port. From my understanding of networking, I have to turn off DHCP on my WiMAX modem, put it in the same IP range as my DIR-615 (192.168.0.100-199), and disable UPNP and NATPMP. After this I'm stuck.How do I tell my DIR-615 to use the WiMAX modem as it's WAN connection?Should I reserve an IP for the modem in my DIR-615?
Region : India
Model : TD-W8901G
Hardware Version : V6
Firmware Version : 6.0.0 Build 120418 Rel.34102
ISP :
Everytime, I turn on the ADSL2+ wireless modem router, it connects to the internet and my laptop gets paired with the wireless network but after 30 mins time, wireless ADSL2+ router restarts itself and goins in a loop for nearly 5 times and then it gets connected to internet but then I cannot connect my laptop to the the router using wireless with error DHCP failed to assign IP but DHCP is enabled in the router. This has started since a month and I had tried several network change settings but nothing has given me a solution. I do use Kaspersky IS through which the connection flows in. My internet setting is set to use Automatic DNS discovery and most time, I get RC 102 DHCP error.
Region : Singapore
Model : TL-WR941ND
Hardware Version : V3
I would like to connect a device (dataloger that sends data to a remote server via internet) which only has LAN port to a wireless network on the location. I managed to do this once with WA901ND configured in Client mode (WA901ND acts like a wireless card for this data loger).Does WR941ND support this feature (which feature should I use?) or should I buy WA901ND again?
I have just bought a TP-Link Wireless Access Point (TL-WA&01ND) and an ethernet switcher (TL-SF2005D).I have put the access point into client mode, allowing me to put it in my room and wirelessly connect to my router, allowing me to plug my PC in over ethernet and use the internet. However, after much fiddling with settings I cannot get it to work, as it continually searches for a network, and then fails to connect, despite the fact it is configured to use the network?I already have a similar setup with a netgear wireless G access point which works, and so I dont understand why the new box cannot do this when using what I believe to be the same settings.
Secondly I have an ethernet switch box which I bought to connect to the access point and switch the ethernet signal between my two PCs, my xbox and PC. This works fine with my primary PC (over my old access point) but when I try to connect my PC i get a DNS failure with auto IP settings and a gateway failure with manual settings, and other devices refuse to connect.
Region : Others
Model : TL-MR3020
Hardware Version : V1
Firmware Version :
ISP :
After I configure the WAN setting on TL-MR3020, my laptop unable to connect to my TL-MR3020 anymore, the message says "windows was unable to connect to TP-LINK_POCKET_3020_B5F9AD".
In my device I am able to browse through & connect to my HOME wifi network ; But after connecting it says 'No Internet Access'.I tried connecting with my SONY Bluray , iphone , ipad , laptops -- everywhere same story.I am able to plug in the ethernet cable directly from modem & able to connect to network.I am not able to open the http://192.168.0.1 -- ( When I am plugged in the modem directly)
Following are my router details
FCCID - KA2DIR601A1
IC : 4216A-IR601
H/W Ver:A1
F.W Ver:1.00 NA
I'm trying to connect to my home laptop from work. The home laptop is connected to DIR-655 router. I set up the internal and external ports to 3389 using both TCP and UDP protocols with the Application as "Remote Desktop". From my work PC I enter the external IP with :3389 and it fails to connect. I have also tried accessing internally which is failing too. All computers are running Windows 7 Home Premium Remote Access is enable on all.
View 1 Replies View RelatedI connected my camera to my router with a network cable. It is a DCS-2121, H/W Ver A2, with firmware 1.04_FR.It received an IP address and I could access it fine with a web browser.Then I configured it to work wireless.I disconnected the cable but the camera wasn't accessible.Since I couldn't find it I re-attached it with a network cable, but this didn't work.So I pressed the Reset button to start over again.However, now I cannot get it to work anymore. When I plug in the camera and have it connected with a network cable to the router the status light remains RED.When I plug it in without a network cable the status led remains RED.When I connect it with a network cable to a computer directly, the status led remains RED.I've tried changing the network settings of my router to use 192.168.0.x as range, but it makes no difference. In all cases the status indicator remains RED.
View 2 Replies View RelatedThis past weekend I went out of town and took my Windows 7 laptop with me -- since I returned home, it has been unable to connect to my wireless network. Other devices in my home connect to the network just fine, and the problem laptop has always been fine until now. My network card is an Atheros AR9285, and I'm attempting to connect to a Medialink router with WPA password protection and AES encryption.My wireless network icon in the task bar has a yellow sign with an exclamation point in it. It says "No Internet access."
View 1 Replies View RelatedI have a TP-Link (TL-WR941ND) wireless router in my living room and I want to expand my connectivity to get to the bedrooms area. I have a D-link (DI-524)wireless G router I want to take advantage of. How can I connect the two routers (no cables to be used) together so I can have acces to the internet from my room?
View 1 Replies View RelatedI have 2 questions about a Network hard disk(for home using).I bought a hard disk (with a network card).This hard disk is connected to my "box"I have 2 questions...Is there a way to increase the speed of writing (20 Mo/s in usb) against 1 Mo/s in network.My second question is to find a way to connect to this harddisk from another network without using VPN
View 4 Replies View RelatedI have a question about my windows systems(XP and Vista) re-connecting to my network folders when my computers restart. I have some shared network folders on my Synology DS410. And then i mapped a network drive to use those folders.But every time i restart my computer i get the message "cannot reconncet all network drives"I have to put in my username and password everytime. I choose Remember login and password.How can i fix this so it automatically connects to these on restart?
FYI...
1 computer - Windows Vista Home Premium
1 computer - Windows XP Home
Both connected via wired LAN
My iSCSI drives connect just fine on restart. Just not my mapped network folders.
