I have an Open NAT but there's some people i can't connect to. I've treed DMZing and it's doesn't seem to get me to connect to everyone, and i've also tried Port forwarding as well.
View 1 RepliesRegion : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
I have this problem i can't open my ports on my D-link 524, i have opened about 6 ports so that my XBOX 360 works with a open nat, i have also set the DMZ to my xbox's IP which is static btw, my PC is also static. This is how i basically tested and it told me that it was not opened. I went into:
192.168.0.1 -> Advanced -> Virtual Servers ->
Enabled
Name: XBL1
Private IP: 192.168.0.100 ( because i was testing it on the computer - if it
were 360 it would be .141 )
Both UDP and TCP at port 3074
Schedule=Always
Apply -> Then restarts modem/router i waited for 2 minutes before turning them on again, i turned router on first because some guide told me to do that.
I did exactly what they did on portforwarding.com then i opened up portchecker and typed in 3074 and pressed check -> This port is NOT opened. What is wrong? This is how my net is set up.
Modem ZyXEL -> D-Link 524 -> D-Link DGS 1005D -> Computer/XBOX.
just upgraded from a Netgear 'G" router to the DIR-655, love the features of the 655 including the USB port. This is the issue, when I connect VPN to my job, I can see all of my files, databases, spread sheets, etc and use them no problem at all. Have a 25 meg connection via Comcast.I can not open my outlook 2003the program opens, however it just sits at trying to connect and then time out. Have tried for 10 days now with no luck. Lan team at job state that "N" routers are blocking traffic and ports that outlook needs, 5 other users have this problem at work.
View 10 Replies View RelatedI'm unable to open a few websites through the DIR-825. I can connect the PC to the ISP modem and these sites open just fine. It's not a browser problem.
I've updated to the very latest firmware and still have the problem. I've also researched this issue and can't seem to find a work-around for this issue.
I was doing a moving job for relatives and had to set their network back up. In a state of fatigue I plugged a higher voltage cord into the router by mistake. Now, even with the right cord, the power lights won't come on. It still gets hot , so I know electricity is getting inside. I believe I shorted the Zener diode or blew a capacitor and would like to repair. Problem is, the case is smarter than I am, can't see a way to open it. It's a D-Link Model: DIR-615.
View 2 Replies View RelatedI want to open MORE than the 24 ports that the router configuration allows (DIR-615 Hardware Version: C2 Firmware Version: 3.03RU)?
View 14 Replies View RelatedI have a DNS-323 that I can;t get my FTP to work.For some reason no matter what I try I can't open ports on the DIR-655I have the virtual server set as such. [URL]. Checked with open port tool.
View 6 Replies View RelatedI have two xbox 360's and two ps3's(my brother has his own set and I have my own). I can not figure out how to have two of them running at the same time with open nats, but if one is on then it has a open nat. Also, when I'am on my xbox and my brother on the ps3, his nat is open and mine is moderate. By the way I have uPnP on and have firmware 2.10.
View 1 Replies View Relatedcant open the ports 2300 -2400 (udp, tcp)on router. What I do isthe following.
1. Open ports on router in port forwarding.
2. Add the triggers as well in APPLICATION RULES with the ports. Triggers are 47624 and 6073.
3. Try both Dis and Enable UPNP. Even try the DMZ enabled settings.
4. Disabling firewalls on Laptop and router. Try both ways on DMZ's(enable and disable) settings on router. Check everything.
Still when I check on websites about the ports and they are shown closed (NOT STEALTH). Router uses a firmware 4.0. I have a windows 7 64 bit system. I use wireless.
Note: All the steps are performed in a combinations manner to see if there is any possibility of opening ports.
I have had this router for a while now and I have been experiencing these problems for forever. I can't seem to have two Xbox360's stay on OPEN NAT type permanently. I have tried port forwarding both xbox's, just my xbox, just my dad's xbox etc.. I have tried DMZ on one with or without the other on Port Forwarding. I have turned UPNP on I have it so the filtering is set to endpoint independent . I have tried without . I have even tried port triggering today. I have manually set static ip addresses on both the xbox and the router. I even have the most recently upgraded firmware. Now... How do I get TWO Xbox 360's on OPEN NAT ? How to get two xbox360's on permanent OPEN NAT status.
View 6 Replies View RelatedII bought a DIR-655 (not sure what rev I have)router and noticed my NAT had changed from open to strict.shen playing Modern Warfare 3 on the Wii. I didn't have that problem with the DIR-615 I replaced. I tried to set it up in the DMZ and I tried the port forwarding and neither of them worked. I am not ruling out operator error. I've tried to piece together the information from several different forums and websites but all are slightly different.
View 5 Replies View RelatedI recently upgraded my DIR-655, H/W Version A3 from 1.21 w/o SecureSpot to 1.35NA. My understanding this that this version isn't supposed to have any SecureSpot support. However, whenever the router is rebooted, the logs contain an entry that reads:
Bsecure remote access enabled on port 8098.
I have tried to open ports, but if I use the [URL], I just get the closed. I have tried to use the Viritual server function, but can`t se to get it open.
On my old, D-Link I also had something cal port forwarding, this is not here. Here is a link to an emulator of the router: [URL]
how to open the tp-link interface setup for my TD-W896ON? i have a user and a password but where do i add them ??
View 1 Replies View RelatedRegion : Others
Model : TD-W8960N
Hardware Version : Not Clear
Firmware Version :
ISP :
Region : Sweden
Model : TD-W8960N
Hardware Version : Not Clear
Firmware Version :
ISP :
opening of some ports 25565 for minecraft so i can host games. i have try so solve this by my self but with zero progress. did enter the advanced setup and then i pressed on the NAT category and then i pressed on the ADD button and enter the following" [URL] and then i used a port checker to look if it worked but did not work?
I have the port numbers but do not know how to proceed from there. Router is a WRT160N V2.
View 9 Replies View Relatedi have 3g mobile dvr, put a sim card directly into it and it gets an ip address and you should be able to view it remotely but i cannot connect. i can ping the ip no problem and i checked that the port the dvr uses (9000) was also open on that ip and i used a locator to trace the ip and it pinpoints the ip to my isp's base so why i cannot connect to it
View 2 Replies View RelatedI have four DCS-942L cameras and a 2012 model Airport Express router. I cannot view live video from outside the router in any fashion other than mydlink.com's poor quality time-limited forwarded video. Here is what I have done.I have manually mapped four TCP ports through the router for accessing the cameras' web servers. This works--I can access the camera settings that way, albeit with NO SSL support (dammit). So, fundamentally, port forwarding works on this router. The "live view" accessed through the camera's web server does not work, though.I mapped port 554 on each camera to ports on the WAN side of my router, TCP and UDP.I have made sure that the external ports set on the camera under "Enable UPNP port forwarding" are the same as the external ports set on my router. (Otherwise the web server wouldn't work from outside.)When I access the mydlink web site from inside the LAN, I can view my video. When I run netstat -n -p tcp, I can see connections open to the local 192.168.0.* addresses of my cameras, so it is connecting via the LAN.If I connect to the Internet outside my LAN, and use the mydlink web site, I get the forwarded, mini-sized video with a 60 second limit. netstat reveals that connections are being attempted to the INTERNAL ip addresses of my cameras, which of course cannot succeed from outside. In addition, if I try to stream video using QuickTime Player from outside, using the URL [URL], the player connects, then says "waiting for stream" and then "switching transports." It gets stuck there and does not proceed. On the LAN, using the local IP address, I can stream video just fine.
Any way to change this?What other ports do I need to open to make the video stream work? I tried mapping ports 5556-5559 to one of my cameras, but that did not work. Also, I have four cameras and need to be able to map to all of them for this to work.The AirPort Express supports "NAT Port Mapping Protocol" which, from my limited research, is not the same as UPNP. How to successfully viewed video from outside a router without using UPNP?I have scoured these forums considerably and have read some success stories using UPNP. From the DCS-942L manual, it seems like I should be able to set up manual port forwarding in some fashion to make the video stream work. Clearly, though, some auxiliary connection is being attempted and the client cannot get through to the camera. Is it possible to even pick this statically, or is the port always dynamically chosen by the camera and therefore absolutely must be set up on the router using UPNP? If I can't make static port forwarding work, then these cameras are headed to camera heaven soon.
Region : Others
Model : TL-MR3420
Hardware Version : V2
Firmware Version : 2.1
ISP : PTCL
trying to connect to router configuration (after several factory resets) at 192.168.0.1 but each time screen displays invalid username / password,doesnot even display username / password window,using admin as username and password,just cannot log on to configuration setup
Recently had an external security scan done on my DIR 655 and scan results are stating I have an accessible TFTP Server running. i've been through all the settings, and even upgraded to the latest firmware. Yet security scans are telling me I've got a TFTP Server running. Why would one be showing on the external interface, and how can I stop it?
View 7 Replies View RelatedRegion : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 0.5 v000e.0 Build 121225 Rel.42874n
ISP :
Just checked and port 7547 which is used for CWMP is open by default even if the settings are showing disabled. Try http://"external IP address":7547
unable to connect my fb and skype. due on brown-out last 1 1/2hrs,it was not completely closed.
View 1 Replies View RelatedWe bought Cisco Prime Infrastructure 1.2 appliance. The application seems to be pre-installed. I have gone through setup process. But I cannot connect/open web interface [URL].
View 10 Replies View RelatedThe Lg840g is a tracfone with wifi capability. I get strong wifi signal and connection at home, but receive failure to connect to requested host message when I open the browser. This phone works at wayport wifi, so I assume it's a compatibility problem with the router. Is there a fix? (Router works great with our Acer and Kindle tablets though.)
View 1 Replies View RelatedRegion : Others
Model : TL-MR3020
Hardware Version : V1
Firmware Version :
ISP :
After I configure the WAN setting on TL-MR3020, my laptop unable to connect to my TL-MR3020 anymore, the message says "windows was unable to connect to TP-LINK_POCKET_3020_B5F9AD".
In my device I am able to browse through & connect to my HOME wifi network ; But after connecting it says 'No Internet Access'.I tried connecting with my SONY Bluray , iphone , ipad , laptops -- everywhere same story.I am able to plug in the ethernet cable directly from modem & able to connect to network.I am not able to open the http://192.168.0.1 -- ( When I am plugged in the modem directly)
Following are my router details
FCCID - KA2DIR601A1
IC : 4216A-IR601
H/W Ver:A1
F.W Ver:1.00 NA
I'm trying to connect to my home laptop from work. The home laptop is connected to DIR-655 router. I set up the internal and external ports to 3389 using both TCP and UDP protocols with the Application as "Remote Desktop". From my work PC I enter the external IP with :3389 and it fails to connect. I have also tried accessing internally which is failing too. All computers are running Windows 7 Home Premium Remote Access is enable on all.
View 1 Replies View RelatedI have a TP-Link (TL-WR941ND) wireless router in my living room and I want to expand my connectivity to get to the bedrooms area. I have a D-link (DI-524)wireless G router I want to take advantage of. How can I connect the two routers (no cables to be used) together so I can have acces to the internet from my room?
View 1 Replies View Relatedhow do you connect to d-link without key
View 1 Replies View Related I had a dual channel netgear n600 set-up at 2.4 GHz working with three machines. I replaced it with the DIR-655 using my laptop to get better signal levels on one distant PCs . I setup the router from the laptop (win7) with the DIR-655 connected to the Cable modem output and did the set-up. Used the wizzard and the laptop is now working fine on the wireless network . Then went to other machines and the wireless signal as indicated by the laptop was fine. I reset the networking details on these PCs (Win 7 and win XP) and used the assigned network name, dlink, the security / pass key and same WPA security as prescribed on the DIR-655 router - to set up the network connection on these machines. The network adapters are fine on these machine but they will not connect to the dlink router. The win XP PC sees the network but the Win7 machine will not even see the network. Have doubled checked all the settings and I cannot see that anything is wrong with the settings ?? Note I do have an apple iphone that seems to be picking up the signal fine. Have turned off the modem and router numerous time but still have same problem.
At one point I had to return to the preset DIR-655 settings since the ID and pass word I had set would not longer allow me to access the router ?? I also notice that one D-Link panel says the UID is Admin whereas it was originally shown to be admin but could not be changed
I have recently had issues with my dlink which has been happily working for around 2 years. Now suddenly it will not connect to the Internet at all, I can find networks but it simply refuses to connect at all. I'm having to post this on my iPod so I can't even download any alternate drivers etc
View 2 Replies View Relatedhow do i connect d-link router to another d-link router
View 1 Replies View Related