'Use Unicasting' is selected by default in the Dynamic IP (DHCP) connection type.I turned it off based upon the router's support text since the router gets an IP address from my cable modem.I don't understand this option at all. I've searched for data on the topic and I can't make sense of it.I think I made the correct selection by un-selecting 'Use Unicasting.'
View 14 RepliesI have some older devices on the network that only support RADIUS (not TACACS) for authentication and would like to have them use SecureACS 5.3
I understand that by default, ACS only supports TACACS for device administration. So I'll get this error when trying RADIUS:
11033 Selected Service type is not Network Access
Description:
RADIUS requests can only be processed by Access Services that are of type Network Access
Resolution Text: Verify that the Service Selection Policy rules are correct
However, even after adjusting the Service Selection rules and seeing hits, I still see the same message in the logs, as if it has no affect.
I recently noticed my 'Number of Dynamic DHCP Clients' on Network Settings is always empty. Before, it always registered a list since there are several devices that are connected to our wireless network (laptops, mobile phones, desktops).
View 3 Replies View RelatedI have my dap-1522 connected to my dir-655 in bridge mode. I was having intermitant connection problems with the dap-1522, so I updated the firmware to 1.41 for version A1. Now when I go to change the connection type to dynamic ip and save, it reverts back to static ip, which makes this thing useless for my network. Why won't it save?
View 6 Replies View RelatedSo network was running fine for about a year or so. Network consists of 1 Motorola SB6120 cable modem attached to a D-Link DIR-601 wireless router. All settings were default except for SSID and WPA password. One day I just couldn't access internet anymore. I've narrowed it down to the default gateway that is being given out through DHCP. The default gateway that is being given out is the IP of the modem (192.168.100.1) and not of the Router (192.168.0.1). I can't find any option on Wireless router to be able to force the gateway address when handing out the gateway IP. Theoretically I thought I should be able to put router on same subnet as modem as 192.168.100.2 but that still doesn't work. If I set the IP adresses statically on the PCs and give it the Gateway of the Router everything works fine. I should mention this is for my boss' house and basically I dont want him calling me everytime he has a friend come over and I have to talk em through setting up a Static IP.
And just for an example this is what I get if I use DHCP:
IP Address: 192.168.0.155
Mask: 255.255.255.0
DNS: 192.168.0.1
Default Gateway: 192.168.100.1
And If I want it to work I have to change the default gateway to 192.168.0.1 I've tried updating routers firmware and reset to factory default numerous times. Is it possible for a router DHCP stop working?
Region : Italy
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 120822
ISP : TIM
I have a compatibility problem with the 3G USB Modem ONDA MT191UP with 3220 V2 updated with the firmware 120822 uploaded on TPLINK web site . Every thing is ok , the wireless is created , but the internet connection is missing . The router does not show the USB led , and it remain always in "connecting" but nothing happen . Do you have some infor to be compatible this USB modem ( some firmware , some Bin file etc..) ?I checked the Huawei E1800 and it works perfectly.
Is there a software that can be used to disconnect internet connection on selected system on a lan
View 2 Replies View RelatedI am connecting a uc320w to sbs2011 - and having the server do the dhcp - but the Cisco box can't connect to the wan - but it's been fine before I set changed the topology - do I need a static ip address for the wan
View 1 Replies View RelatedI have just upgraded our WLC from 4.0 to 7.0 (via 4.2). Before the upgrade we had our ACS returning a VLAN based on user group. This seemed to be working without an issue. Now that the WLC is on version 7 this is no longer working correctly. The ACS is returning a VLAN and passing the user but the client can not get an IP from the DHCP server configured.
Example configuration:
SSID-----VLAN
PN-CSC-----CSCVlan: Works
PN-Others------OthersVlan: Works
PN-Others-----CSCVlan: No DHCP
When users are trying to be allocated to a vlan that is different from the native one the DHCP fails however both WLANs are configured to point to the management interface so dont have any real connection to the vlan other than by name.
Have there been any changes I haven't seen in the way the dynamic vlan allocation works in version 7?
First of all i do not have that much know how within this field (Although i work for an ISP)
There seems to be a problem with my DIR-655.
#1. As we speak the router is taking down and setting up the connection about 1-2 times pr. minute! the connection uptime is stuck in a infinite loop: 1.12 sec, 1.13, 1.14 and back to 1.12 sec. It comes back from time to time. but this is the second time this have happened.
[Code].....
I have been using the subject Wireless Router for more than 2 years. Most of the time it worked OK but lately it has been giving issues. [code] Due to a recent power outage, I had to reset the setting on the Dlink router. One of the issue is after resetting the Internet options and rebooting the router when I go back to the system screen, both the Release and Renew buttons are greyed out.I have tried to reboot the router as well as cable modem without any success. The Cable Modem is Motorola SB5120.
View 3 Replies View RelatedI have some LSA type 5, I want to change it from type 5 to type 3 before send to another Area, How can i do it?
View 1 Replies View Relatedi want to know what is the type of wire used for a dsl connection
View 1 Replies View RelatedI have cable modem (one of those Motorollas), ehternet cable connected to desktop pc (usb would be probably the same), Windows7 - host, Virtual Box -> CentOS6 - guest; no static IP, no router.I am trying to connect guest and host together and both to the Internet, there are suppose to be 3 ways to do that:
1) Adapter 1: Host-only adapter + Adapter 2: NAT; I've been trying to get it to work for a while now, but I cant; here is some info: VirtualBox Configuration (no IP for the guest? I've seen it there before though, so there might be a way to do that)
2) Bridged adapter; I think that the only way to do that is with a physical router at home or office etc; VirtualBox 4.0.2 Network Connections in Windows 7 - YouTube
3) NAT and port forwarding; I think this might be the only option, here is some info: url...
I have the dhcp server setup and working on our main 3560x.
The only problem is that it is not assigning the dhcp clients a default gateway.
I was not able to find it in the Cisco documentation and a google search is not useful either.
i followed the instructions on the link and I can not for the life of me get my NAT to display OPEN or even Moderate. Always says STRICT. I have tried all the link and all the videos about forwarding ports followed all the instructions to the T. But the PS3 in the DMZ. And still, Nothing. It's BS.
Using router FW: 2.00NA
Ports Forwarded: TCP 80-81,443,5223
UDP 2005,3074,3075
TCP 3074
UDP 3478
Assigned QOS engine rule to the IP of my PlayStation and set it to priority 1.UDP Endport Filtering and TCP Endport Filtering Both set to independent?Enabled Anti-Spoof Checking?
]Region : Philippines
Model : TL-MR3220
Hardware Version : V2
Firmware Version : 3.14.2
ISP : globe telecomms inc.
i just bought an antenna for my new tl-mr3220 v2 router that is 9db. my current one is he 5db that was supplied together wit the unit. then when i installed the new antenna, instead of an increase in the range it lower than my old one. is there any specific antenna or type that you can use? if so what types of antennas?
I have been having this problem randomly on and off the last week or so. If I type facebook in any of my browsers it comes back with the connection has been reset. If I use hidemyass I can get onto facebook though. My partner is having the same problem. I haven't got a firewall blocking facebook and it works sometimes and other times it doesn't so I am unsure what the problem is.
View 8 Replies View RelatedI have 3 Cisco Routers as following :G.SHDSL Router : Cisco 3845 withISDN and Branch Router : Cisco 2811.How My Network works :Branch Router has two type of connection ( First one : G.SHDSL link work as Main link and the other one ISDN Link work as Backup link )when main link goes down the ISDN link goes up ...( Note : i applied IP SLA with tracking ) ...
My Problem :i want to delete default route from ( G.SHDSL Router )0.0.0.0 0.0.0.0 dialer 3..My network works properly with these configuration but when i delete the default route 0.0.0.0 0.0.0.0 dailer3 , my network goes down ( Failover technique not works)
My network topology is as follows:
Internet <-> Residential Gateway (RG) from ISP (OEM: Pace) [192.168.1.254/255.255.255.0] <-> RV180 [192.168.1.253/255.255.255.0] <-> SG500 switch [192.168.1.250/255.255.255.0] <-> rest of network.
I know this is a cascading LAN-to-LAN arrangement. The cable from the RG to the RV180 is from a LAN port on the RG to a LAN (not WAN) port on the RV180.
I eventually want to segment my network into a few VLANs from the RV180 down. I am aware most people would recommend DHCP on the "primary" router, but the RG is non-VLAN aware, so I figure I need to handle the DHCP off the RV180. At the same time, I have also opted not to do a LAN-to-WAN cascade because I want to retain the ability to configure the RG from the rest of the network and not have to cart a computer over to the RG to do it.
On the RG, I've disabled DHCP, and placed 192.168.1.253 in the DMZ.
On the RV180, I've enabled DHCP and put it in Router mode.
The issue is that I do not have any Internet connectivity. If I allow the computers in the network to receive IP addresses over DHCP, the default gateway that is communicated is 192.168.1.253, which is the RV180. If I configure static IPv4 information on my computers to point to 192.168.1.254, I am able to connect outside, as you would expect.
How can I get the RV180 to pass out DHCP IP addresses, but point to 192.168.1.254 as the default gateway? I thought the solution might be to create a default route (or something). I went to the static routes tab but it wouldn't let me enter 0.0.0.0 as a destination IP to route through 192.168.1.254.
Further down the line, is it possible for both the RG and the RV180 to connect directly to the SG500, along with the other nodes in my network? That way the RV180 only serves to maintain the VLANs and pass out IP addresses via DHCP, instead of having it be the choke through which everything goes through on the way out?
I have a Cisco ASA 5500 as the main router with a DIR-655 as a wireless access point behind it. DHCP is turned off on the 655 as the ASA is providing DHCP. This worked great for about a year and now suddenly, without any changes, I'm having problems. The only thing that connects without a problem is a laptop, which shows up on the device list with an IP. Other devices have problems. iPhones connect, show an IP on the device itself, but when listed in the connected list on the 655 show no IP. The connection is super slow. An Airport Express will connect, but again, shows no IP in the connected list on the 655. Using the ethernet cable from the Airport Express, nothing can get an IP. I can live with the iPhone not connecting, but the Airport Express not connecting is a major problem. Any reason why this would just stop working one day?
View 2 Replies View RelatedI have a RV042 router. The problem that I am having with it is that the DHCP is giving out the wrong Default Gateway and DNS Server. There is no option to change the DHCP server IP on any of the settings pages on the router. I am begining to think that there might not be a way to do it. I see that there is an option for the DNS under the DHCP page but the Public IP that is being handed out is not the one on that page. I also have 2 WAN connections hooked up as well a DSL link and a Cable link (the cable link is the primary one).
The following information is provided in an effort to resolve this issue:
IP of Router 10.0.0.2
IP of DHCP Server (the one that is being handed out):10.0.0.1
IP of DNS (the one that is being handed out): 10.0.0.11
What I want to it be.
IP of Router: 10.0.0.2
IP of DHCP 10.0.0.2
IP of DNS 10.0.0.2
Region : Italy
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : wind infostrada
TD-W8970 Wireless connection problems|
Region : Italy
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.2 v000c.0 Build 130201 Rel.54921n
ISP : Wind Infostrada
That's a wonderful router on the paper! Really it has some problems with the wireless connection and the dhcp server. After 2 days of i must forced to reset the router because it refuse any wireless connection while the internet browsing on the other pc connected via ethernet ARJ45 is very slow.To complete the scenario the router doesn't allow any acces to his console page ..so what's the problem?
I try to change any channel for the wireless without no positive result.I bought it on amazon but if this situation will continue without any solution from tp-link i will forced to send it back with a totally negative feedback on the product.
I was searching a lot , but I couldn't find any good example, how to configure DHCP server for our wireless clients on Cisco Autonomous AP. I'm looking for example how to configure Dot 11 radios and BVI interfaces.
I have no problem to configure DHCP server on BVI 1 and VLAN 1 ( native VLAN ) interfaces, but there is a problem with other BVI's and VLANs. Maybe this feature isn't supported? Maybe DHCP server feature is supported to work just with default BVI and native VLAN?
I have the dir-601 as my main router. Its IP settings are dynamic, not static. My second router, the router I'd like to use as the access point is a Belkin Wireless G Mimo. My goal is to setup the Belkin as an access point downstairs away from the main router. I'd like to do this wirelessly. I'd like to phsycialy plug devices into the Belkin, while the Belkin receives access to the internet wirelessly from my main router, the dir-601.
Here's my issue. There's an easy option to use the Belkin as an access point. So I do this and set the Belkin router to an IP outside the DCHP range ( currently 192.168.0.100 - 192.168.0.199 ) to 192.168.0.250. My dir-601 will only recognize the Belkin access point while plugged in physically. I know this because when I did a ping test it only see's the Belkin when plugged into the dir-601 via ethernet cables. My ultimate goal is to simply set the dlink dir-601 to recognize the Belkin as an access point.
I'm having a very difficult time getting my WRT54GS to work with my Westell 6100 modem. I've been bouncing around gathering info, and what I've learned is that the goofy way CenturyLink tech support told me to hook up my old wired router (modem line into outgoing (LAN) router port) is because the Westell 6100 is a "smart modem/router". Therefore, when I run the Linksys setup CD, it sees the modem as a router, and won't properly configure. I've also learned that the Westell modem can be "dumbed down" into simply a modem by putting it into "bridge mode", which is where I'm at right now - trying to get it reset to factory defaults and resetting the connection type from PPPoE to Bridge. In the meantime, I also reset the WRT54GS to factory defaults, and now I've got another problem: the router will not allow me to set up encryption. The default setting is "Disabled", and when I click the down arrow and try to make any selection at all (preferred selection is WPA2 Personal), it reverts to Disabled. I've also tried to change the router's IP address to 192.168.2.1 (and alternately to 192.168.1.253), so it won't conflict with the modem's IP, and it freezes up every time I try.
View 2 Replies View RelatedRegion : Portugal
Model : TL-MR3220
Hardware Version : V2
Firmware Version : TL-MR3220_V2_121126_UK
ISP : OPTIMUS (26803)
I buy a Router TL-MR3220 and Forwarding e Dynamic DNS not work. I installed the latest firmware version (TL-MR3220_V2_121126_UK) and does not work well.
We just purchased the WRVS4400N router with high hopes. For some reason, our ISP provides a connection through L2TP Dynamic for a static IP. I repeat, L2TP Dynamic. Is there anyway to properly configure the router to use such a connection method. I only see L2TP Static, which seems to be the standard method for many routers.
View 1 Replies View Relatedlaptop could not connect to wifi. Other laptops can connect to this same wifi but this one can't. tried laptop on other routers and it was able to connect. The error message displays" Windows cannot connect to the selected network.The network may no longer be in range...." tried the solution on microsoft but didn't work. Tried changing the ssid of the wifi then scanned for it. it showed that it was changed. The laptop can detect the wifi but it can't connect to it.The laptop is running on windows xp.
View 2 Replies View Relatedchrome has an application that auto translates any text that is selected, directly in the browser.is there something similar for IE7? I dont wanna install some toolbar or any visible program, just a program similar to the chrome application, that translates selected text and displays it in a pop up.
View 3 Replies View Relatedurl...Yesterday all of a sudden my computer wouldn't load up a lot of websites. A lot of my favorite sites to visit now for whatever reason only load to a certain point than stop. The first picture is from Steam, the second is from a browser. It doesn't matter the browser, because it doesn't load on any I've tested.
View 2 Replies View RelatedRegion : Sweden
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : TL-WR1043ND_V1_120405_
ISP : Tele2 (fiber)
I recently bought your router and I am trying to install it.The problem that I get is that when the router tries to get the dynamic IP from my provider, it gets nothing.I have typed in the DNS servers but no go. Without the router, my uplink works fine. The provider does not lock onto a specific MAC adress.
Windows is unable to connect to the selected network." The network may no longer be in range. refresh the list of available networks and try to connect again." Your in range of the network (right in the same room as the wireless access point). And when you refresh the list, the network still shows up there.It seems that it will only connect to Routers which use WEP security and not ones which use WPA. I have looked on the Toshiba site for the Wireless Drivers to see if there is any updated ones and used the Driver Update Utility on Intel's download site and that tells me that the latest wireless driver is installed.
View 4 Replies View Related