D-Link DIR-655 :: Upgraded To 2.07NA Firmware And It Bricked Router
Jun 21, 2012
I am today playing with the settings in my DIR-655 NA B1 router when I notice that a firmware upgrade is available.I clicked the button and the router automatically downloaded the file named DIR655B1_FW207NAB09.bin. I flashed it and was saying that it needed to wait 180 seconds (3 minutes) to reprogram the router after which it came up with a 404 not found on the screen. I am not able to access my router, it is bricked and I can't even re-flash the firmware comes back with Incorrect hardware ID image, Please check. I notice that the 2.07NA firmware file on the website is named DIR655B1_FW207NAB05.bin. What gives this is the first time a firmware upgrade has bricked anything I own?
View 14 Replies
ADVERTISEMENT
Dec 27, 2011
I upgraded my router from version 1.2 to 1.35NA, through the Tools / Systems page on the router (uploaded the bin file). I am connected to the router via a wired connection.
During the upgrade, the message said I wouldn't be able to access the webpage until 75 secs. I watched it count down the seconds and then when it refreshed, I could not get to my routers page: 192.168.1.2
The DLink Router is connected as a pass through router to my FIOS router, so that I can use the wired ports and I use the DLink as my wireless router (fios router wireless strength was poor).
All the lights on the router are working as though everything is ok. I am still connected to the Internet, so it appears that the pass through of my wired ports is still working after the firmware upgrade, but wireless is not. Not surprising. I expect I may have to upload my settings (which I did save), but since I cannot get to the routers page, I feel a bit stuck.
two more bits of into. I also tried getting to 192.168.0.1, which might be the default? and I cannot get there either. My Fios router is on 192.168.1.1 (and as mentioned, the DLink should be at 192.168.1.2). Fios Router reports that the 192.168.1.2 port is inactive.
View 5 Replies
View Related
Nov 3, 2010
I wanted to upgrade to the latest firmware (2.03NA). Something went wrong and now the router comes up with the orange light flashing. So the system is in emergency firmware upgrade mode. I set my IP to 192.168.0.2 and connect to the web interface at 192.168.0.1. I see a page with "Firmware Upgrade System" and "Version 1.0.0.2". So far so good. I can now select the firmware and click "send". But then nothing really happens. I can wait for a couple of minutes and then run into a timeout. I tried different browsers (Linux: Firefox, Chrome, etc). I even tried it Windows 7 with IE 8 and I get the same result. It seems that the cgi (192.168.0.1./cgi/index) is not really doing anything?
View 12 Replies
View Related
Jan 3, 2012
I have a little problem with my new E1200. Before the E1200 I had a WRT160N that was bricked to death by a power surge due upgrading the firmware. Till that moment the WRT160N met al the required specs as told in the description..I have from my ISP a 40Mbit cable line and was always downloading at those speeds wired aswell as wireless...
Now with the E1200 I get the 40Mbit only wired... wireless it only allows it up to max. 20Mbit.I figured that I didn't do anything different than the Linksys I had before..I'm working with a MacBook from late 2007 running OSX Lion 10.7.2, Built-in AirPort Extreme card (802.11a/b/g/n)My wireless setting with a WP2 Personal Security Mode
View 6 Replies
View Related
Jun 27, 2012
just to relieve a little those who complain for the loss of functionalities/control caused by the new firmware, I want to let you know that yesterday evening when I came back home the router was bricked. After more than 2 hours of tests with the online support, they ended up the device has to be replaced.To add insult to injury, I ALSO HAVE TO PAY to ship my router to Cisco warehouse. I couldn't believe my eyes... It's not for the 10 bucks it costs the shipment (even if 10 bucks are much better in my wallet than in Cisco's), but I already spent around 300 bucks less than 2 months ago to buy the two devices and now I have to pay to fix something I have not broken.
View 4 Replies
View Related
Jan 4, 2012
I tried to upgrade the firmware of my WRT350N but while upgrading my wife switched on the oven and.... yes, power down -> the upgrade has been interrupted. Now the router is no longer responding, it shows just the green power light on (not blinking). I tried all the resets I found googling (pressing the reset button for 30 sec, isconnecting power and reconnecting it again) but no way, there's no way to ping the router at its default address 192.168.1.1. All the leds are switched off (internet, usb, wireless, security) except the green power light. Is there another way to have it back or it is definitely lost?
View 6 Replies
View Related
Feb 26, 2012
I own a Linksys BEFSR41 v 3.1. I've been attempting to set up a home network with three computers; my main desktop running Windows 7 Pro x64, a netbook running the same OS and a box running Windows Home Server 2011 x64. The firmware listed for my router was initially 1.05.03.
My router has the issue with resetting its administrative password to the factory default and I've been unable to set up remote access to my LAN and home server. I decided to try updating the router's firmware, but none of the versions listed fit the one I have. The label on my router says v 3.1, but Cisco's site only has a 1.0, 2.0, 3.0, then skips to 4.1, 4.2, etc. The instructions on the site warn not to use a version for a different model, but are vague as to exactly what that refers to, as the model # and the version # aren't clearly delineated.
Anyway, I tried using the latest firmware and received the, "File Pattern," error. Although it didn't seem like anything had changed, I reset the router just to be safe, then tried the v 3.0 firmware update, thinking that the software was intended for all revisions of v3.0. This time it reported updating without a problem, so I reset the router again and went back to the admin page in my browser to check the firmware version listed. To my annoyance, the firmware is now listed as 1.05.00 - i.e. an earlier version than what was shipped on the router.
This means that not only is the issue of the password resetting not fixed, but any other fixes included in the original firmware are now wiped out as well and, needless to say, I still can't set up remote access properly.
How do I restore the firmware version? Neither a reset nor a, "Restore to Factory Defaults," does this. How do I find an actual update for the router? I can't find any mention of a v 3.1 on Cisco's site, let alone support information specific to this model and version.
View 1 Replies
View Related
Jan 5, 2013
I just downgraded to firmware version 2.07NA from 2.10NA to test a wireless connection issue with my wife's IPhon4s ISO 6 not connecting as N device only shows as a G device.My router version 2.07NA is now jerkier than with version 2.10NA. Firmware 2.10NA seems to me to be more fluid with web pages. I am going to switch back to firmware 2.10NA.
View 1 Replies
View Related
Aug 7, 2011
I was having problems with the speed being between 30-58 kpbs when going through the WRT160N router, whether its hooked up wired or wireless, the speed with both was extremely slow and wouldnt fully open pager or would take dsl day slow. I hooked up straight to modem and I got 100+ kpbs so I figured its not my ISP, so I read that upgrading my firmware might make it faster, so I upgraded and hit and held the reset button for 30 secs like it recommended but now the 192.168.1.1 wont open, I get a message saying it cant open this page
View 4 Replies
View Related
Jan 5, 2012
I have the Linksys BEFSR V2 router and at least once a day some or one of the ports become inactive and have to unplug the router and plug it back in to reset. I have ungraded to the latest firmware but this is still happening on a daily basis.
View 3 Replies
View Related
Jul 22, 2012
I can't seem to get the router to adjust for DST for Mountain Time. Enable Daylight Saving is checked. Time zone is (GMT-07:00) Mountain Time (US/Canada). Daylight Saving Offset is +1:00 Things I've tried that don't work:
1) Unchecking Enable Daylight Saving. Save/reboot. Check Enable Daylight Saving again. Save/reboot. No difference for Mountain Time but makes a difference for Pacific time. See item 5 below.
2) Adjusting the offest to +2:00. Save/reboot. No difference in time so it is completely ignoring this setting.
3) Factory reset. Only settings configured after the reset are the time settings.
4) Tried 3 different NTP servers. Not surprising this has no effect as the time zone and DST information is not part of the protocol.
5) Change time zone to Pacific. Save/reboot. Has correct Pacific time adjusted for DST. Uncheck Enable Daylight Saving. Save/reboot. Correct Pacific time without DST. Change back to Mountain Time and Enable Daylight Saving. Save/reboot. Time is 1 hour behind what it should be for Mountain.
6) Change time zone to Central. Save/reboot. Has correct Central time adjusted for DST. Change back to Mountain Time. Save/reboot. Time is 1 hour behind what it should be for Mountain.
View 3 Replies
View Related
Jan 2, 2013
I just setup my new Cisco EA4500 and upgraded to latest firmware and signed up for my account.Local access to the router works fine and I see the Smart Wi-Fi admin/config interface However when I try to go to the following site: url...To access Linksys Smart Wi-Fi Tools, your router <em>requires</em> the <a href="url...Series Linksys Smart Wi-Fi Firmware</a> and you will need to associate your router with your Linksys Smart Wi-Fi account.On a computer or device connected to your router, open url... and follow the instructions. This requires that you enter the router password so have that ready.
However I see no way to perform the association step - my account exists and my router is configured.I am doing all this behind this router wi-fi network not remotely.
View 4 Replies
View Related
Jun 6, 2012
I bought E900, accessed setup thru 192.168.1.1, upgraded its firmware.. then changed router's IP, it reboots, then went blank, I cannot access the setup page anymore?
View 9 Replies
View Related
Aug 14, 2011
I have upgraded the firmware on my Linksys BEFSR41 V4.3 router. On this router i used Statis IP (so DHCP enabled). This worked fine on my network, until this upgrade. Now when i try to ad another static IP , or when i want to change something in the Routing-tab, i get this message ' Wrong Gateway Input! It should be the same subnet with WAN IP'. Strange because i haven't changed anything in the settings.I already did a complete reset on the router, still the same problem.
View 7 Replies
View Related
Mar 17, 2011
Tell me whether my router is Ipv6 capable.Firmware Version: A1.01.09 , 2008-06-13Boot Version: 0.22.02,My Isp is not using this protocol yet, but I want to be ready.
View 2 Replies
View Related
May 26, 2011
I have a big problem with my cisco wap4410n .. I have upgrade the firmware of this AP to V2.0.3.3 for supporting multiple SSID after my upgradation is finished ..one time I can able to access the administration page But when I connected to another system the same AP I cannot able to connect through ethernet .The network connection in the system shows connected for one second and not connected for the next second its simultaneously repeating the same ..and still not connecting ..i changed my ip setting to default ie 192.168.1.xxxx and again to old config 192.169.3.xx any way the same instance is showing ..
In the WAP the power led, wireless led , are connected good but the Ethernet led is blinking off on stage.I have many times hard reset the WAP but off no use the same happens .i could not able connect to WAP.This may be the worse case ever seen in wap4410n …
View 1 Replies
View Related
May 7, 2012
I can't win. After dealing with the internet dropping once every two weeks, I decided that upgrading the firmware might work. Turns it all it did was exacerbate the problem and now my internet drops every few minutes. I've been plugged into my modem for a good 20 minutes at this point with no drops. Has my router just shit the bed or can this be fixed?
View 8 Replies
View Related
Nov 29, 2011
I previously owned a Linksys WRT54G V.8 wireless router, I upgraded my router to a DLink DIR-655 N Router in hopes to improve my internet download speeds. As a comparison I ran several online speed test for both routers. However, All test yielded similar results with minimal improvements. I also downloaded large files utilizing rapidshare's download manager, again with no improvement in download speed. I thought moving from a G to an N router would improve my download speeds. The drivers on the DLink router are current. Are there any tweaks or tricks i can do to increase my download speeds?
View 7 Replies
View Related
Jun 6, 2012
I have bricked my DIR-825 when performing an upgrade of DD-WRT. Now I am not able to go on to the Recovery Web page. ( 192.168.0.1 ) after performing the 30/30/30 rule, wich always worked before.
I had done an update of dd-wrt and lost all of my wireless adapters, they said to load open-wrt, find the caldata and write this. This all worked. But after a reboot, the deviced bricked on me .
View 3 Replies
View Related
Mar 30, 2011
When my RV220W used firmware 1.0.0.26 the PPPoE login to AT&T/Bellsouth DSL worked just fine. I upgraded to version 1.0.1.0 and now it won't connect. The PPPoE connection still works from my prior Linksys router so there wasn't a change on the ISP side. Has something changed in firmware 1.0.1.0 that requires a change to the PPPoE profile?
DSL Modem is a Motorola Netopia (model 2210-02) with firmware 7.7.3r10 operating in Bridged mode.
View 26 Replies
View Related
Aug 22, 2012
I upgraded from Vista 64 bit to Win 7 64bit and one of the first things I've noticed was that youtube videos take forever to load, I use to stream on 720p videos in realtime but now even 360p can struggle to load, 480p videos you have to pause for 30 seconds. Oddly, speedtest indicate my full 15mbps down and 1mbps up, regular downloads go fast but streaming youtube, vimeo, or anykind of videos take a while.
My initial guess was that it has something to do with the Wi-fi PCI card. I have D-Link dwl G-550 and on windows compatibility center it says its not supported. Windows 7 automatically detected and installed its own drivers, it works ok.
View 19 Replies
View Related
Aug 1, 2012
I purchased an e4200v2 to replace my old WRT160n which I have been using for years with no issues. Last night the e4200 crashed on me when I went to reset the router I noticed the CISCO light was blinking very slowly and I had no network connection. I power cycled the router and still no connection so I hit factory reset button. Nothing happened. Did a 30/30/30 reset nothing happened. At this point I have a 34 day old plastic brick on my desk and I'm back to using my old WRT160N. how to unbrick this router?
View 3 Replies
View Related
May 20, 2010
I originally began with a WRT610N(basically the old version of the new E3000). I had been using it for a couple months, when all of a sudden I was stuck with the power light flashing, meaning the firmware was corrupted. I contacted support & they guided me through the process of trying to restore the firmware through using the tftp.exe program with no luck. Unfortunately at the time this happened, the E3000 was just being released, so they stated it could be close to a month to get a replacement WRT610N! So I decided to just go grab an E3000 from BestBuy, as I had some unused giftcards for there. I bought the E3000 & used it for literally 2 weeks, then the exact same problem! Power light flashing, firmware corrupted. Again I tried to restore the firmware with no luck. I should mention, each time I tried pinging the router after setting a static IP it resulted in a 100% packet loss, meaning the router was not even communicating with my PC. So with it being within the 30 day period, I just went & swapped it for a new one. Went and swapped for another, so I am now on my 3rd E3000 in less than a month! What could be causing this? I notice the router does get fairly hot, but i have it in a well ventilated area, so not sure what more I can do about that.This is supposed to be the highest end LinkSys router out there & I continue to have major issues with each of them. Now I do pull a lot of data through it. I have a NAS, 3 PC's, PlayStation3, Xbox 360, Wii, iPad, multiple notebooks, etc. on a 18Mbps Comcast cable connection. But shouldn't this thing handle high amounts of data? I mean it's the highest end router LinkSys makes, so what do I need to do? Buy a true Cisco router for $1,000 for home use?
View 9 Replies
View Related
Oct 27, 2010
I accidentally flashed my WRT310N version 1.0 with version 2.0 firmware. After which the router was dead as a doornail.After a frustrating 3 hours of reading forums, following over 11 tutorials, and being 1 second away from throwing my WRT310N at the wall, I finally fixed it.I performed this fix on a Windows 7 32-bit PC. My provider is Comcast.Make sure you only have one ethernet cable connected from your PC to the router. The cable should be connected to any one of the 4 blue ports. I connected mine to port 1. DO NOT CONNECT IT TO THE YELLOW INTERNET PORT on the router.
With the router in your hand, hold down the reset button for 30 seconds until the port 1 light goes out then immediately disconnect the power while still holding down the reset button. DO NOT LET GO OF THE RESET BUTTON!WAIT 30 more seconds with the power disconnected. (Do not let go of the reset button)PLUG the power back in and WAIT another 30 seconds. After that, let go of the reset button. You should have held the reset button for a total of 90 seconds. This will wipe the router's nvram.Bring up the command prompt window that you prepared earlier. You should still see the ping command that you entered in Step 2. Now, hit ENTER to start pinging the router continuously. You will probably see a bunch of "request timed out" responses.Bring up the TFT2.exe window that you prepared in step 2. Press UPGRADE so it can begin communicating with the router. Make sure you set at least 10 retries.
As quickly as possible, go back to your router and HOLD the reset button and disconnect the power. You don't need to wait 30 seconds...5 seconds is enough. While stil holding the reset button down, plug the power back into the router and keep an eye on the command prompt and TFT2.exe windows.If the command prompt has successfully pinged the router, TFT2.exe will begin to flash it and very soon it will show a success message below the progress bar. If you still can't successfully ping the router, close and restart TFT2.exe using the same settings and try disconnecting/reconnecting the router's power again as mentioned in the paragraph above. You may want to try holding the reset button down longer than 5 seconds. I was able to get this to work on the FIRST TRY.Now that your router is has the proper firmware, go back to your adapter's settings (mentioned in step 4), delete the static IP and set it back to the default automatic settings.Plug your cables back in and don't forget to plug the ethernet cable from your modem to the yellow internet port on your WRT310N."Recycle" the power to your cable modem by holding down the reset for 60 seconds or disconnect it from the power outlet for 60 seconds.Reset your router by holding the reset button for 30 seconds.
View 7 Replies
View Related
Jan 2, 2011
I attempted to upgrade the firmware on the WRT54G2 V1 (the newer, slim black model) but it failed. I let the upgrade run for about 10 minutes and it just sat there and link to router disconnected I run ping for 192.168.1.1 but response is "DESTINATION HOST UNREACHABLE". The router is now completely unusable and the ALL LAN ports lights are ON and Internet light is also ON.
View 9 Replies
View Related
May 12, 2011
Sometimes even if my connection is cable my router gets a yellow light..what can be the most stable firmware to use?
View 3 Replies
View Related
May 9, 2011
a friend of mine(from the US) gave me this router. i am currently living here in the Philippines. and as I check my router's homepage, it gives me
Product Page: DIR-655
Hardware Version: A3
Firmware Version: 1.21
when I go to tools>firmware and check for the latest version, I get
Current Firmware Version : 1.21
Current Firmware Date : 2008/10/09
This firmware is the latest version.
I don't experience problems using this firmware but I think it's outdated because most of the users in the forum uses new firmwares.
where can I download firmware that is suitable for my router?? and is it risky?
should i download from the D-Link Philippines website? (the router was not bought here)[URL] or North America Firmwares should work fine on my router?
View 8 Replies
View Related
Mar 27, 2013
I have a BEFSR41 that often goes brain-dead and the DHCP stops working. I've tried three times to download and install new firmware but it always fails with a "pattern mismatch". My current firmware version is 2.00.02 and the file I am downloading is 2.00.04 build 8. Yes, I have verified that my hardware version is 4.3.The download file from this website is corrupted.
View 1 Replies
View Related
May 16, 2013
I updated my dir-655 firmware to 1.36WW after the update I the router has been restored to factory settings and every time I try to change any setting it gives me: "ap should not be locked before configuring". I cant change set any configuration, cant change even the router time!I logged in to the router as admin and left the password blank.
View 2 Replies
View Related
Nov 28, 2011
I previously owned a Linksys WRT54G V.8 wireless router, I upgraded my router to a DLink DIR-655 N Router in hopes to improve my internet download speeds. As a comparison I ran several online speed test for both routers. However, All test yielded similar results with minimal improvements. I also downloaded large files utilizing rapidshare's download manager, again with no improvement in download speedI thought moving from a G to an N router would improve my download speeds. The drivers on the DLink router are current
View 1 Replies
View Related
Nov 29, 2011
I recently updated my firmware for a DIR-601 router and have internet while hardwired, but no wireless. I saved the configuration settings before updating, but this doesn't even matter because my wireless router doesn't even show up in the list of available wireless network connections. Why isn't my router showing up? I tried a few things like unplugging it and resetting it, but nothing seems to work.
View 3 Replies
View Related
Nov 4, 2012
Region : India
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.14.2 Build 120822 Rel.57775n
ISP : BSNL EVDO
I have one BSNL EVDO data card which was working fine before firmware upgrade to latest 3.14.2 Build 120822 Rel.57775n. Now it is keep on saying device unplugged after identifying the device. The device is working fine while connected on my laptop.
View 14 Replies
View Related
Jun 29, 2011
For some reasons, my internet connection keeps dropping more often recently. My laptop still says it is connected to my network but I can just not have internet connection. It was not like that before but it happened more frequently now. What I did was to power off then on the modem and the router and everything will work fine again. I want to upgrade my firmware but I just wonder if I need to save all the configuration before doing the upgrading? If so, then how can I set it back to the old configuration that was saved?
View 5 Replies
View Related
