I have an telemetry equipment which have one ethernet RJ45 port, so I have an internet connection and I can connect to this device remotely using a browser on my PC for security reason I want to feed this device with a second internet connection that is coming from a cellular line , can I just put the two different Internet cables into a switch and from that switch connect my device?
View 1 RepliesI have this adsl wireless router but my internet connection only has RJ45 directly connected to my PC. My questions is how can I use my ADSL wireless router with this kind of internet connection.. because I really want to make my connection wireless..
View 1 Replies View RelatedHotels have wired LAN connections and not wireless. Is there a device that will plug into the ethernet cable and offer wi-fi for more than one laptop/smart phone in the hotel room?
View 1 Replies View RelatedPurchased a 2911 router for a customer, and I'm sure I'm missing a module here.
Teleco installed T1 and left connection to smart jack. Router only has 2-3 copper ports.
Can I get away with configuring the blackbox with RJ45 to the copper port on the router ethernet or do I need to purchase a HWIC ?
I installed the DIR 655 router using the install disk. I hooked up my Vista desktop machine via the ethernet port. I also activated a Roku box and my Itouch successfully via the wireless.I turned MAC filtering on and manually entered the MAC addresses for the three devises. Everything worked fine.After I rebooted the desktop, I could no longer get to the internet via the desktop connected through the ethernet. The Roku Box and I-Touch both work fine and enjoy a strong wireless connection.I've tried rebooting the desktop several times, but still can not access the web. I also can not access the router by typing in 192.168.0.1. I entered the configsys stuff and verifited that I am using the right numbers.
View 14 Replies View RelatedI have internet line came from my neighbor throught his hub directly connected to my laptop.. My problem is, i buy wireless ADSL model router but when i check the DSL line port its rj14 which i can not connect my RJ45 internet line. Addtional information, my wireless router have another 4 port LAN. Can i connect my internet line to LAN port,if it so how will i configure the router..
View 1 Replies View RelatedI have Cisco 800 series (888w) with BRI-ISDN port. Is there any way to change the usage of ISDN port to normal RJ45 port?I want to use this SOHO router to sharing connection.
View 0 Replies View RelatedMy parents have a windows 7 desktop with ethernet plugged in for internet. I use a Asus EEE 1005HA with jolicloud. They do not have wireless, only wired internet. When I plug in the ethernet cable, the netbook doesn't recognize the internet access. Nothing wrong with the ethernet port on the netbook, as i've used wired network at my dorm and the port does recognize the ethernet cable at my parents' house.
Also, is it possible to use the desktop as a sort of wireless router? Would connecting a usb wireless dongle to the desktop allow me to connect my netbook to the internet via the desktop?
I have a WRT160n that I am trying to forward some ports on for some DVR equipment. When I use the single port forwarding and enter each port separately it works fine. But I have 2 DVR's and they use a bunch of ports each so I want to use the port range forwarding because there are not enough spots in the single port forwarding section. The ports I am trying to forward are 8000-8004 for one IP address and 8005-8009 for a second IP address. I have entered it into the port range forwarding section but I can not connect from outside my network. As I said if I enter them in the single port section seperately as 8000,8001,8002,8003,8004 then I can connect fine outside my network.
View 7 Replies View RelatedThere is no "blinking light" indication on my E3000 at the Internet (Yellow label) and Ethernet port no 4. I tried plugging in 2 cables at all of the ports. I got the blinking indication at Port 1 through 3. The same cable's have no response at Port 4 and Internet port. As a result my I am not able to connect to the internet.
View 2 Replies View RelatedWhat type of Mini-GBICS should I used for RJ45 ethernet connections for my 4402 Wireles Lan Controller? Should I use the GLC-T SFP? Is it the right one? aAso is Mini-Gbics a industry standard which means I can use any brand of Mini-GBIC for this Connection like Dell Brand Dlink or Others.
View 1 Replies View RelatedIs it possible to use my atom mini itx with pci + pci nic card and creating a firewall? No possible problems between using the motherboard port and a pci port? I'd like to fool around with smoothwall or another firewall software.
View 6 Replies View Relatedprocedures to connect RJ45 port to the network cable
View 1 Replies View RelatedI have an old 2007 model Toshiba HD LCD television. It does not have a USB port, but it does have a connection for RJ45. I want to convert this to a USB port, Is there a converter/connector for this purpose?
View 3 Replies View Relatedis there an adapter ( wifi reciver ) that plug into RJ45 port so RJ45 can receive wifi signal ?
View 1 Replies View RelatedGot BT Infinity installed today, thought I would ditch the Home-hub 3 and go back to my tried and tested WAG320N. Got it configured, set the first ethernet port to WAN and got a connection.Ran speed test.net and comes out at 26Mbit.using the Home-hub 3.0 I get 37.5MBit.
View 4 Replies View RelatedIs there a way to view the utilization on a WS-X6148A-RJ-45 ASIC/port group?
View 7 Replies View RelatedI am learning the 2911 router. Is there a way to set a physical single RJ45 port to handle multiple WAN IPs? Or do I need to buy a port expansion module.
View 12 Replies View RelatedOne of branch locations has a Cisco 1941 Router . The port details are as follows
-Gi0/0 - ISP line
-Gi0/1 - Inside Network ( To a 2960 Switch)
Now they have procurred another line from ISP through which MPLS based VPN to the Main location is configured. What are the options I have , to terminate it on the Router ? As all the On board LAN ports are filled I guess I wont be able to do anything with the current setup .Are Switching modules available ? What is the Embedded-Service-Engine0/0 port that I see on #sh ip int b output ?
I have my bigpond internet setup on my main pc,works fine connected to a router but i want to connect to the internet via ethernet cable on my 2nd pc. I have a ethernet port on the wall near it so that should work. I don't want to run a long ethenet cable from my router to my 2nd pc because there's a ethernet port right next to it.
View 6 Replies View Relatedgetting near my home internet keeps shutting off and i lose the internet for half hour periods of time or more now im sure it will get worst as the storm gets closer. i run my cell phone usb tethered to the pc how do i setup my pc to share that internet from the ethernet cord so i can say run my xbox online plugged into the pc ethernet jack?
View 2 Replies View RelatedWe have recently purchased 2 x 4900M switches with the following configuration:
2 x X2-10GB-SR installed in port te1/1, 1/2 (optical)
1 x 20 x 1GB RJ45 installed in the top left of chasis ge2/1 - 2/20
1 x WS-X4908-10G-RJ45 8 port 1/2 card in the top right of chassis te3/1 - 3/8
We have te1/1 connecting the 2 switches, and various vlan's and connections on the 1GB RJ45's with no problems.
However, we have a number of 10Gbps BaseT connections te3/1 - te3/5 which are causing us issues. On a reload of the switch or removal / re-install of the cable it can take anywhere up to an hour for the port to become active again. So when we reload the switch, we may get a connection come up after say 3 mins, but the port next to it may not come up for 15-60 min. The cabling is all the same (CAT6 and has been tested/verified) and all connections go to Broadcom 10Gb cards in Dell 820 servers running vmware. We have the following set on the ports:
switchport mode access
spanning-tree portfast
No speed or duplex can be set on these ports - these options are not available in the config.
Once a link is finally established, it will hold the link solid with no problems, but this is a problem for us, we can't have a reboot take an undetermined amount of time for the link to come back.
I already configured my LAN connection to only have an IP address, and a subnet mask, leaving default gateway blank
View 3 Replies View RelatedMy Storage supports RJ45 Connectivity. Some it gives slow performance. What if i connect all the Macpro using fibre optic and use some sort of converter to convert all the fibre connection to LAN. Will it increase performance?
View 2 Replies View RelatedI have the DIR-655, Rev. B running 2.07NA firmware, and have a strange problem with my wired clients. I have my primary computer/desktop PC connected via wired connection. I also have several wireless clients (laptop, iPad, iPhones, etc.). All have been performing normally. However, in December I connected a wired weather internet bridge to another ethernet port on the DIR-655.
It functions as it is supposed to, and all other connected devices do as well. But here's the problem - whenever I use the desktop PC (the only other wired connection) to do anything on the internet (mostly just web browsing ... I don't stream media from the internet on it, I don't do torrents....nothing out of the ordinary, and nothing really of high bandwidth), the wired weather bridge cannot communicate with its associated website. This continues as long as I'm using the desktop PC. When I stop using the desktop, the weather bridge resumes normally.
I have researched the weather bridge, and it is simply doing POST transactions (or so I'm told) to the website listening to it. It doesn't wait for acknowledgements or anything...just keeps POSTing updates. I tried reserving an IP for the weather bridge and the desktop, enabling QoS, and prioritizing the weather bridge (100 vs. desktop at 125), but it didn't work. I've tried moving the weather bridge into the DMZ. I'm totally baffled how just using the desktop to browse the internet could completely block the traffic from the weather bridge.
On the weather bridge support site, they suggested that I insure I'm not connected in gigabit speeds from my computer to the router, because in the past that has been known to cause issues on clients not running that speed, but I don't think my desktop is connected in that fashion. According to the settings, it can do 10 or 100, full or half. I have it set to AUTO.
I have a Dell Laptop Latitude 610 and I have not been able to connect to the Internet via the ethernet cable port for some four months now. I've tried downloading software from Dell's web site, I bought (and returned) and USB to Ethernet cable, only to find out that it was a model ahead of what this machine needs.I've asked local repair place (Microcenter) what it might be, but they'll only tell me after I pay $70 just to open it up.Another repair guy said that it is probably the motherboard and it wasn't worth fixing. (Yet if it was, wouldn't the entire computer decide not to work at all?) [code]
View 3 Replies View RelatedI was very happy working with my WRT610N connected to the ethernetport of my previous internet modem. Recently I had to switch to a new modem CISCO EPC3925. Unfortunately this combination does not work anymore. I don't get an internet connection on my WRT610N anymore. I therefore have to connect all computers (LAN and WIFI) to this EPC3925. Especially for the WIFI I'm not fully happy. My IPAD2 sometimes does not want to connect, a problem which never occurred when connecting to WRT610N.
I probably need to change a setting, but where? In the EPC3925 or in WRT610N?
I have two computers in my house that are connected via ethernet using a switch. One computer is connected to a friends internet connection by wireless using a satellite dish. That computer is on XP and I have configured it as follows (IPv4)[CODE]
View 4 Replies View RelatedHow can I get 2 internet connections for 2 in home computers from 1 cable internet connection.
View 1 Replies View RelatedI have an internet connection that enters my house using a CAT5 cable through RJ45 type socket - Currently I have a desktop that is connected to the Cable - I want to share my internet connection - The desktop should have a cable connection and want to connect a laptop as well which will connect using wireless as well as cable as and when required - I will not be using both computers at all times so do not want to make my desktop a server or the laptop a server.
View 3 Replies View RelatedI've had trouble connecting to my own internet and have no wireless. I'm using my neighbor's wireless and it's really slowing her's down. I've tried restarting my laptop (it usually works) and then reinstalled the device under "device manager". It's not the cord, I've checked with my neighbor's laptop and it works fine.I use a Sony Vaio VGN-NS140E with Windows Vista SP2.
------------------------------------------------------------------------
{ipconfig /all} This is while I only have an ethernet plugged in and no wifi connection.
Windows IP Configuration
Host Name . . . . . . . . . . . . : FairyHo
[code]....
First is your output from TSG SysInfo program:
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 8, 64 bit
Processor: Intel(R) Core(TM) i5-3450 CPU @ 3.10GHz, Intel64 Family 6 Model 58 Stepping 9
Processor Count: 4
RAM: 32643 Mb
Graphics Card: Intel(R) HD Graphics, -1984 Mb
Hard Drives: C: Total - 304892 MB, Free - 237708 MB;
Motherboard: MSI, Z77A-G45 (MS-7752)
Antivirus: Windows Defender, Disabled
You must realize that I live away from the city and only have an iPhone 4 for a hot spot. It connects via WiFi, Bluetooth and USB. I have found USB quicker, but it doesn't seem to work under Windows 8. So I connect via WiFi only.I have a LAN, based on a D-Link DIR-615 router. This router has a WiFi option and has a Buffalo File server attached to the device that we use as a backup/file server and personal 'cloud'. When I am connected via WiFi and I plug in the Ethernet connection, the computer overrides the WiFi and attempts to connect to the Internet via the Ethernet port. It does know that the WiFi is connected as it is displayed on the bottom of the status bar as 'Internet', but choices to ignore or not check. I have gone to the devices and changed the priority to be Wireless on top and Ethernet on the bottom. This is done via the "Network and Sharing Center", "Change Adapter Settings", ALT-F (to get "File, Edit, View, Tools, Advanced and Menu" options), "Advanced" and finally "Advanced" again.Then put them in the priority you wish. Ethernet still overrides this and times out when I attempt to access anything on the Internet. It works the same on my wife's Windows 7 Laptop. It returns to normal if you unplug the Ethernet cable. Since I wish to have other files available, it is a pain in the bottom to have to unplug the Ethernet cable every time you change over to do something else and I usually forget and have to deal with the 'can't connect' message.It might be a simple solution to connect via WiFi to the router then hard wire the computers to the router, but this hasn't been a workable option. The router doesn't seem to be able to handle that type of connection?
I have had my HP laptop for 2.5 years now, originally bought with Vista 64 bit. It now has Windows 7. Up until now, internet access and connectivity have been working fine. But, all of the sudden today, I couldn't get Internet Access despite trying both an ethernet port and a wireless connection (connectivity was working.) I know it's something with the laptop, because my ASUS netbook has no problem accessing the internet. I've tried looking around at some of these tech support sites and haven't really found anything that's worked for me. I've tried using CCleaner to remove any temp files and clean the registry, and resetting internet settings in the command box, but still I get nothing.
View 5 Replies View Related