I used several of these wireless nick's in various systems. Installation was always done without using Te Linksys monitor. Just the installation of the driver via hardware management.
View 4 RepliesI had been using my Linksys wireless-G PCI adapter WMP54Gv4 in a PC running XP (SP3) and an Airport Extreme wireless router for the past 4 or 5 years without any issues. Then recently, my wireless signal had become flaky on all client machines (on both PC and various Macs, which reported weak signal and kept dropping and searching for a new PPPoE from my DSL line). AT&T verified our line was fine and even sent a new modem but troubles persisted, so I bought a new Airport Extreme last week. This solved the network reliability issue on the Macs just fine.
However, the PC with the WMP54Gv4 adapter now crashes whenever the new Airport Extreme is turned on. There have been no hardware or software changes on the PC, yet it now reliably produces a BSOD stating "DRIVER_IRQL_NOT_LESS_OR_EQUAL". This crash also happens when booting in safe mode with networking. I can avoid the system crash when booting in safe mode without networking or booting normally without my Airport Extreme turned on, though I do see this error: "Linksys Wireless Network Monitor: Access violation at address 0040756D in module EMP54Gv4.exe"
So I cannot run any tests of the PCI card on the machine when the wireless network is on, since the operating system crashes.
The evidence thus points to an explanation where my wireless network from the new Airport Extreme is tripping up the operation of the linksys wireless card in a way that XP hates. I know the wireless network is OK, since it works fine on my Macs. I confirmed that my driver (v3.0.3.0) is still listed as current for this PCI card, so it's not a matter of having an out-of-date driver.
Here's another observation that may be relevant: When I first started using the new Airport Extreme with WPA2 protection, the PC could run without crashing, but it could not connect to the wireless network. I also had trouble connecting via my Macs. Then I switched the Airport Extreme to use WPA/WPA2 security, which is when the network-based PC crashing ensued (though the Macs can now connect just fine).
So, I bought a used WUSB600N Wireless Adapter and am having difficulty installing it. Of course, there was no installation CD to go with it, so I went to the website to download the drivers and updates and still can't get it to install.
View 1 Replies View RelatedTrying to install on Wi 7 32 bit. When starting driver installation I receive an ACCESS DENIED error and the driver does not install.
View 1 Replies View RelatedWhen I insert the disc for my new AE1000, the setup opens automatically and begins to run. Before even letting me read the software end user license agreement, I get a screen that says the following: "Our Customer Support team can assist.Your Linksys Adapter was not successfully set up."I can not figure out any way to keep this message from showing up.
View 4 Replies View RelatedI have tried numerous times to install the disk and the adapter, but it always says it cannot locate the adapter. I know that the ports (I have tried them all) are working properly because they have been in use. I tried the chat. He suggested I call the 1-800 number. I don't have time to wait on hold forever, which I did anyway until I finally hung up.
View 5 Replies View RelatedI am having trouble installing the wusb100 adapter on a Windows 7 Pro 64 bit machine. I have downloaded the updated files and when I go to install the software, I get to the section that says, "plug in the adapter." At that point, it says it can see the adapter and it sits for 3 minutes trying to complete the install. The I get error 211 which says the adapter is plugged in wrong and to try again. I notice that the adapter is set up with drivers in the Hardward Management area of Windows, however, I cannot access the adapter to set it up. Thoughts? I have also tried to manually install the drivers but they are installed. The trouble is I can't see the adapter.
View 2 Replies View RelatedI just installed windows 7 on my wifes new com and the device couldn't detect any connections using the default drivers (windows called it an nvidia wireless network card). I downloaded the drivers put them on her hd via flash drive and attempted to update the device drivers through the device manager but it says the drivers are already up to date. I uninstalled the device and windows called the device MCF-J415W and when I tried to update the drivers again it said the drivers were not correct. I'm not sure what is going on here and why linksys doesn't just have a .exe driver installer. I've had the same issue with my wife's computer when it had win xp except it didn't have any generic drivers to install. Also I tried selecting the driver from the list of pre-loaded drivers and found one for the exact device but it would not install those either.
View 2 Replies View RelatedI have spend some time today trying to get my WMP600N-EU PCI Adapter installed. However up till now without any success. I run the installation CD with instructions, but the adapter is not found when I mount it into the PCI slot. I have tried both slots without success. Each time I get error 212.
View 8 Replies View RelatedIt used to work, but just stopped. We have tried to reeinstall but it won't recognize the adapter. I cant click the next button to continue installation. I have changed USB ports and restarted the computer. I have unstalled Norton 360. But it still won't install.
View 3 Replies View RelatedMy desktop can go to internet with ethernet wire on. After installing wireless adaptor driver, the adaptor shows green solid light on 'power' and blinking light on 'Link'. The Linksys icon shows 'Cannot associate with the access point'. I called Verizon and was told that the adaptor might have problem. I want to know if really the adaptor's problem or the adaptor installation problem.
View 1 Replies View RelatedI have a router attached to my Dell desktop running Windows 7 and am trying to install the AE2500. Instead of using the router, I want the AE-2500 to access my HotSpot wifi on my cell phone. I go through the AE2500 installation and Device Manager shows it is installed properly. However, I do not see the adapter in my list of available wireless connections and I'm unabley to disconnect my router connection. I keep clicking disconnect but it never does.
View 1 Replies View RelatedAfter I installed on Win7 OS, I can't find the Power Save management of WUSB600N which on Windows XP I can see it in following path:Wireless Network Connection Status > Propeties > General > Configure > Advanced > Power Saving Mode. PS: I installed the newest version for Win7 OS.
View 3 Replies View RelatedI did a clean install of Windows 7 64-Bit the other day. I installed all drivers that came with my PC's Hardware, all went smooth. INCLUDING: Installing the original Linksys WMP300N Software/Driver Disc. I'm not sure how it installed, since i have a 64-Bit OS. It says that "This device is working properly", although no "Power Managment" tab came up in its Properties Menu. I had to manually go to the Registry Editor and turn off Some "Power Saving Features", like it auto-turning off. That's all i did an i'v had NO problems with it. Although, I don't use the software, and never have, i prefer Microsofts. I'v also got a second PC with a different Linksys adapter(Non PCI One)working great on 32-Bit Win7. How to get it to work on Windows 7?
View 9 Replies View RelatedI came into an old Win 7 computer (64-bit) with a WMP54G v4.0 wireless card in it. Apparently the driver had already been installed previously but when I booted the computer it didn't acknowledge the existence of the card or drivers. I installed the driver from here[url]... and restarted the computer when prompted (the card was already in the computer). Upon restart the setup was supposed to complete, but it never came up. When I re-ran the setup it just said the driver is already installed.The card still isn't being recognized, scanning for new hardware in the device manager doesn't bring it up. There is an entry for a "Network Controller" with no driver installed, it may be the WMP54G but trying to manually install the driver doesn't work. Windows just says it can't find the driver even when I point the install wizard right to its location.
View 1 Replies View RelatedHow can I get a installation CD for a WRT54GX2 Wireless router? Can you download from internet?
View 3 Replies View RelatedI plan on replacing my linksys BEFW11S4 wireless router with a new linksys WRT120N wireless router. Should I completely remove and unplug the old router before inserting the startup CD and beginning the installation process for the new router?
View 3 Replies View RelatedI currently have an E1000 router set up on a 2006 Dell PC as main hub of a network that includes kids' 2003 Dell PC (with a Cisco Connect USB receiver plugged in because it has no wireless capabilities) and wife's Dell laptop. We're about to change main desktop computer to an iMac (2011 refurb, won't be running Lion which I know there's issues with as far as Cisco Connect), give the 2006 Dell to kids and get rid of the old 2003 box. I cannot locate my installation CD, I'm sure it's somewhere in our rather cluttered computer area, although I understand I can download what I need. This probably is a dufus question, and I apologize in advance, it's just not clicking in my mind, but basically am I going to have to go back to step one, just like the first day I set up the router, as far as setting up our network?
View 3 Replies View RelatedI have a WRT120N router up and running in my home. I had the software (Network Magic) that came with the router installed on my old laptop. The hard drive died on the laptop and now I cannot seem to find the CD. When can I find an online download for the software?
View 1 Replies View RelatedI just bought EA4500. The CD come with it does not support Mac OS 10.8.
View 9 Replies View RelatedI just got a new WRT54GL wireless router to replace my WRT54GS failing router and I have a question. It's been awhile since I installed the old router and I remember something about not using the CD as it says before plugging in the new router because it messes everything up. All of my computers are running XP Pro SP3 with 2 of them being wired.
I remember something about just plugging the router in and typing in 192.168.1.1 in my browser and then setting everything up that way. Am I correct in doing this or am I forgetting something?
Oh, I am also running Network Magic so would I also have to reinstall it?
I bought a Linksys-Cisco wireless G Broadband Router model # WRT54G2 some time ago, and I never installed it. Now I cannot find the set up CD-ROM or the user guide CD-ROM. Is there a way to down load these from the product site...
View 9 Replies View RelatedI am installing the router but keep getting stuck on the 4th step and getting an error code 321. i currently have cable internet, which is working but when i follow the instructions it wont work. I cant access 192.168.1.1. I tried through google chrome and internet explorer but neither will recognize it. I just started school and would like to use wireless internet on my new laptop instead of cable on my desktop.
View 9 Replies View RelatedBought a E2500 Linksys Router, i updated with Firmware Version 1.0.03 ( Build 4 )no problem,!! it is connected directly with a RJ45 Cable, router to Computer,no firewall on at all ,wide open yes i am on internet !! but here is the Problem i get everytime !! ---> ( Cisco Connect Setup Software For PC ) what it does is that it installs agreements etc.. password and all but near the end it tells me i am not on the internet you have been disconnected ! ;( and stops everything from continuing installation and i have to uninstall all from registry etc.. then re-install again and get same problem everytime i got a e3000 and it is great.
View 1 Replies View RelatedAfter popping in the installation CD, the screen says hook everything up, which I do. Then click next, where it says "Searching Networks", then quickly changes to "Connecting to Network", and then it says it "Cannot Find Router.". Err. Check setup, etc.If I hook up directly to new router VIA internet cable. Also, this is strange: When I just open up a web browser and try to log into the router 192.168.1.1, using no user name, administration as the password, it won't let me in to the router. Even after I have reset the router with a pen.
View 1 Replies View RelatedI have desktop and two laptops. I have DSL connected with my desktop only. If I'm gonna install E200 so I can use my laptops in internet, wouldn't it effect my dsl connection in my desktop?
View 1 Replies View RelatedGot the cisco EA4500 router, installed it and ran the set up disc. It downloads whatever it needs to download, then proceeds with a progress bar all the way to 100. Then it tells me my internet cable is unplugged, but I able to browse the intrnet, like now. It tells me to plug it in and hit next, I hit next and it eventually gives me the same message. I've tried unplugging my modem, resetting the router etc. But when trying to run the disc when it gets to that point it always tells me my internet is unplugged? I can even browse the internet while that message is up.
View 9 Replies View RelatedI've currently got a WRT54G and have an opportunity to buy a WRT54GS. The problem is that the seller of the WRT54GS has lost the Set-Up Wizard CD & Hard Copy Quick Installation Guide. Obviously I have these items already with my WRT54G. My question is this. Are these items different for the WRT54G or will the stuff I already have for the WRT54G "work" for the WRT54GS.
View 5 Replies View RelatedI have a small issue with Remote Management on my E4200v2.I have enabled it , select https and set Allowed Remote IP Address to any on the default port ( 8080 ).After all of this, I cannot connect to my router from my office or any other place. I'm using DDNS and all its ok ( updated at time ). I've tried also connecting to my direct ip address ( dynamic ) but with no result.P.S. no incoming log from port 443 using https.
View 3 Replies View RelatedI plugged in a 2TB external USB drive and restarted the router. The Disk Management tab appears blank, doesn't give option to format.
View 4 Replies View RelatedI have an issue with new Win8 & IE10. When I try to access web management interface of my wrt160nl (Firmware Version: 1.00.01 B15) via HTTPS I'm receiving the foolowing message:"Continue to this website (not recommended)." If I click on it another error page appears:"Certification error: Navigation blocked. There is a problem with this website's security certificate"
At the same time I'm able to acccess the management interface via HTTPS, but from my laptop with Win7 & IE9. There if I click on the red Certificate Error > View certificate and the certificate information is:Issued by: Linksys Issued to: Linksys Valid from : 1.1.2009 to 1.1.2010
So I'd like to know if I could update the router certificate or what settings should I use in IE10 in order to access the web management interface via HTTPS?
I want to be able to login to a router remotely and foward a port on the router. I thought i saw a spot for remote management but don't know how to use it. I have a dyn account and can create a dns for it.
i setup security dvrs on the internet so clients can see cameras from outside their homes. I would like to be able to login to a router if i need to foward a port or something similar.
I can not even get in to management mode. In next program that just keeps trying to auto repair the connection and never displays any radio button option the direction state like "advanced settings".At the very least your PDF should match your user friendly **bleep** ware!The instructions even refer to itself wrong! It states "for manual set up go use browser connection section" then in that section it describes an auto set up and instructs you to follow the set up steps on the CD.
View 7 Replies View Related