I have a Linksys E2000 router & a HP Officejet 6500A PLUS all-in-one printer. While printing, at a certain moment, the printer stops printing, rolls the sheet out & act like nothing happened. But, when i use an adhoc connection, the printer works just fine. So i think there has to be something wrong on transport (router?)
View 5 RepliesI have a issue with using a Media Server in my WRT160NL. I have tried several firmwares, but issue exists in all firmwares.I tried to play files on my Samsung LCD TV with embedded media player (this player can play files from USB storage or from DLNA servers). I have several video files in mkv and avi format. My TV has wireless connection to router (270Mbit). And I have the following situation:1. I write these files on USB drive, plug to TV, play in embedded player - all OK.2. I have a samsung DLNA server on PC and try to play the same files from PC via network - all OK. (My network - PC to WRT160NL via cable, TV and some other devices via WiFi, but in this time only TV via WiFi.)3. I plug the same USB drive with same files to WRT160NL, go to settings and enable Media Server, choose two folders for scan (one for MKV, one for AVI), scan it. I run player on TV, choose WRT160NL. TV can see all video files, but:- when I try to play mkv file - I have error after several seconds "the unsupported file format"- when I try to play avi file - it plays, but after 20-40 seconds I have error "WRT160NL is disconnected".What is wrong with DLNA server in WRT160NL? Because from other server via router all OK. USB drive in NTFS format, maybe I need to use a ext3 or other file system for DLNA?
View 2 Replies View Relatedhave a HP 6500a All In One Printer in the network with a BERSR41 V3 router. I am using a Imac with this sytem for printing and scanning. For some reason I keep loosing the printer when I try to scan? I have it set to a static IP, and can not ping it, but can access the printer throught the network with the HP Utility. Am I missing something in setup on the router that causes it to keep loosing connection?
View 2 Replies View RelatedI have two computers. My host computer runs Windows 7 64-Bit. Last December I upgraded from Home Premium to Ultimate, which may have changed my configurations though a month before I had to do a complete reinstall of the Home Premium before I acquired the upgrade. My remote computer is XP-Pro. The HP connection is wireless. There is no problem printing; but to use some features the HP on its control panel requires me to enter a proxy address. How can I configure my router settings to fully use the HP web services? At this point, the HP doesn't even update. I cannot access things like apps, ePrint and other web printing functions because of this sudden need for a proxy connection. It doesn't even show the email address for the device.
View 9 Replies View Relatedthe printer was working fine with my old router, but with the new one, it doesnt' see the network.... It can see other wireless networks fine.
View 9 Replies View RelatedI suddenly am unable to print the settings on the My Network Settings. When I click on the print sign nothing happens - it does not register on my printer. I used to be able to do this. My router is WRT54G and my printer is HP Officejet J3680 All- in-One.
View 1 Replies View Relatedi just bought an HP Officejet 4500 wireless all-in-one printer. i imagined this would mean that my laptop can print to the printer without a USB cable, but also that the printer itself would not have to "cable" to anything, but rather be wireless and located anywhere in the house. was i wrong? does this printer HAVE to connect physically with the router box?
View 1 Replies View RelatedI can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies View RelatedI would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies View RelatedWe bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
View 2 Replies View RelatedSo i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
View 4 Replies View RelatedE2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies View RelatedI've been looking around like a madman now in the settings. where can I turn off my WPS ? Just cracked my own PIN within 6 hours with Reaver.
View 9 Replies View RelatedMy internet cut out last week and after calling my ISP I found out it was in fact my router that was causing the problem (regular connection to PPOE works fine). I've only had my E2000 about 2-3 months and have not had any problems with it. I've restarted the router, done a factory reset, upgraded the firmware, renewed the IP and still I cannot get any connectivity. I can access the router UI fine and I get a response from pinging it and also I have tried replacing the cables but that didn't fix the problem either.
View 9 Replies View RelatedI have an E2000 that I was given as a gift. I would like to use at it my office for a switch at my cubicle where I can connect 2-3 computers simultaneously. I am in a large network and am a user only. When I hooked the E2000 up today my computers would not get internet access BUT my laptop got wireless access and internet.
View 2 Replies View RelatedI'm using E2000 currently and meet a wireless connection problem. The speed can up to 300M bps. When I confiured the E2000 to band auto (20-40mhz) and my wireless network card to work at also auto (20-40) mode, it always down to 144M speed when connection.
If I changed some settings in E2000's wireless configuration, in the status sheet I can see it works at 40MHZ. But after a while,(5-10 mins) it automaticly down to 20MHZ and my labtop connect only got a 144M speed.
how can I deal with that to make it always keep at 300M connection? Note the previous router I used to connect to my lattop can always keep that speed.
I have a E2000 router that would go out and I would have to unplug and replug in every once in a while. Finally it just stopped working completely. I reset the router and now it won't let me connect. I have followed advice given to soembody else on here and went into router settings and cloned the mac, the IP address was there and reset my security settings. It let me connect to the network but not the internet...
View 2 Replies View RelatedI have a Linksys E2000.
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.
I have a Cisco E2000. When i connect to my cable modem directly, I get 30-35 MBps down and about 10 up. When I plug in to my E2000 it does that at first... but slowly over time, the speed degrades, usually down to about 5-6 down and 3-4 up. If I unplug the router, it typically restores full speed, but not for long (a few days maybe). Also, when I unplug the router, it is pretty hot.
View 4 Replies View RelatedFor Xbox 360? currently, whether wired or wireless, my Xbox 360's NAT type is strict, and I am unable to do anything online whatsoever. Is there anyways to set up an exception, or anything that can open my Xbox's connection to my router so I can actually use it online?
View 2 Replies View RelatedIm using a linksys e 2000
Is there a way to block more than 4 websites, and 4 keywords?
I have an E2000 router that has an intermittent issue where Bonjour drops out. Suddenly my Apple TV won't see my computers, and my iPad won't see my network printer. This happens whether the Apple TV and computers are connected via wired or wireless interfaces.
Restarting the devices does not solve the issue.
Restarting the router solves the issue (until it happens again...)
My router is version 1.0, with 1.0.04 firmware.
I have a e2000 router and a wmp600n wireless card in my desktop pc. Everything works fine until I enable 40 mhz for faster speeds in the e2000 router. When I do this the router switches from 20 mhz to 40 mhz and I get the faster speed. But the effect of this is that my pc gets all "choppy". What I mean is that everything freezes up every few sec. For example when im minimizing windows, the windows freeze half way for about a sec then unfreezes. My mouse does the same thing, even my sound is choppy. I have to switch my router back to 20 mhz and then everything is fine again.
Using windows 7 64 bit
Using newest dirvers and firmware from Linksys.
I have a E2000 for a half a year now.We have been on hollyday for 5 days so my routers has been shutdown.Today it happend 3 times that my complete LAN disconnected for no reasonI didn't have any wired or wireless connection.
View 5 Replies View RelatedI have the Linksys E2000 and set it up on MacBookPro no problems. My iPhone 3G and my gf's iPhone4 connect no problem. Also, I have an XBox 360 connected via ethernet cable. Her MacBook however is constantly not getting an IP. I set her up with an EZ Key, but every time she connects we have to go through the EZ key process where I run Cisco Connect from my laptop. Why can't she just log in every time? This is frustrating me as all other aspects of this router work fine. I had her plugged into it as well with no problems. Again, it works after a dual computer Cisco Connect cycle, but my computer isn't always home.
View 1 Replies View RelatedFor some reason my new E2000 will not connect to our Charter TV Cable internet service. Another router works fine with same cabling. I have reset EVERYTHING numerous times and cross patched -- hard patched, wireless to where my finers are bleeding. My ISP is DHCP and requires no login. So my router is set to automatically connect. Could the router be defective?
View 1 Replies View RelatedI got a refurbished E2000 on Amazon. Last night I set it up and when I tried accessing this website [URL], I could not connect to the server. First I thought it's the server problem and let it go. This morning it's the same probelm. I called my local cable technician and he told me it's the wifi router is blocking the website. I called the CISCO guys and they refused as it was out of warranty.
View 2 Replies View RelatedI want to set up another wireless laptop to access my e2000 but i dont remember the network key, How can I retirieve the key? through cisco connect maybe?
View 1 Replies View RelatedE2000-RM router has been working fine until about 2 days ago. Wired connection still works fine, but the wireless signals seems to be dropping in and out. I have a couple wireless devices and they all seem to be experiencing problems. Using the network connection bar on my laptop sometimes it shows a strong signal and connects no problem. Then all of a sudden the signal is gone (drops off list). It can be both the main and guest signal dropping, other times it might just be the main, etc., etc. Sometimes it shows a signal but will not connect and then a few seconds it might connect, or drop entirely. I guess the best word to describe it is highly erratic. Distance does not seem to matter. I can be 2 feet away and get the same behavior. The indicator on the box shows a signal at all times.
View 8 Replies View RelatedI have new PC with Window 7 and trying to set up E2000 on new computer with original set up CD. States I need go back to my old computer and set up new key and transfer to new computer. I do not have access to old computer. getting set up on new computer?
View 3 Replies View Relatedmy internet connection cuts in and out so my computer cant connect to the router and it wont show up. I am on a windows 7 toshiba laptop and i have comcast as my internet service provider.
View 1 Replies View RelatedAfter a recent lighting strick close by I can not connect to the internet through my router. Stright from the modem works fine. The port light on the router does not come on. I rebooted modem, router and computer with no luck. It's like I've lost my network adapters and I don't know how to get them back. I tryed another E2000 and it's the same way.
View 1 Replies View RelatedI have an E2000 (2 yrs old) that is not connecting to the internet.It is a slave to a BEFSR81 which controls the DNS.I am able to connect to other computers on my home network, so I know the wirelss is working and the cables are all good. I know that I can plug my laptop into the port on the hard wire router that the wireless was plugged into and I can get internet. So the only thing I can think of is the inernet is being blocked at the E2000.
View 1 Replies View Related