I'm in the process of installing a Virtual Clustering for studying and wanted to get some mail filtering for my Exchange 2010. Of course my clients and what I normally use is cloud filtering like mimecast, etc. Any know of a local filtering software or a virtual machine that does filtering I can place between my IP and Exchange?
View 3 RepliesI am trying to configure a NIC IPv4 with IPv6 disabled on a virtual machine (win server 2008)The instructions I got say that I need to use IP 192.168.210.0/24.However when I enter this IP and use subnet mask 255.255.255.0 I get the following error. Why this is and if there is a way to resolve the error?
View 3 Replies View RelatedI have a PC behind a DSL router. In my PC (WinXP SP3) I have a virtual machine also running WinXP SP3. I would like to access the VM via remote desktop. Since I have a dynamic IP, I use the(url)tool to solve the problem. I installed the no-ip sync tool in the VM. Now when I write my no-ip address in the remote desktop from my office, I will access my host system, and not the hosted VM. Does any knows how I should configure things in order to get access to the virtual machine and not to the host machine
View 5 Replies View RelatedI wish to access my virtual pc remotely, As i have downloaded OTRS ticketing system on a virtual machine and i wish to access it remotely. The physical server IP is 62.84.xx.xx the Virtual server IP is 10.0......"check link below please"
View 2 Replies View RelatedI still use some old applications on windows XP.So I run them on vware.I could visit the real PC from virtual PC without any problem.But I could not visit the virtual pc by another real PC.No matter how I change the connection type.
View 1 Replies View RelatedWe have purchased LMS 4.0 -300 and were wondering how well the software will perform on a Virtual Enviornment.
View 3 Replies View Relatedhow to transfer the messages or files from one virtual machine to another virtual machine in oracle virtual box
View 1 Replies View RelatedVIRTUAL MACHINE ~ Can Guest OS become Infected Through Host OS ?If I setup and use a virtual machine running/containing both a Host OS and a guest OS ... do they remain completely separate entities when operating one or the other?My main concern is Virus related ... if for instance I'm Running Windows 7 as the host and XP as the guest and I get the host OS infected, will the guest XP OS also contract it by default because it is operating on the same disk?
View 1 Replies View RelatedImplement the procedures required so that machine 1 and machine 2 can communicate statically with one another. Outline the TCP/IP settings to be used on each of the machines and set this machine up accordingly. I followed this guide http:[URL]....tid=210 but what has happened is that now the two machines can't connect to the internet. How can I fix this?
Here is a links to the ipconfig/ all on the XP virtual machine http:[URL]....the default gate way here is the same as on my actual working machine.
I am running a websever on virtual machine on ubuntu .how can i forward all traffic coming to my ip to virtual machine which is 192.168.1.4 on my LAN.here are my configs.
OS - Windows 7
Router - DLink
Virtual machine network Setting - Bridged adapter.
I have created a virtual server that hosts a ticketing website on it, locally i can access the website when i input my private ip .
Now i want to make it accessible to the agents outside my company , i have change my private ip to a public one, but the problem is still there,i cant connect . i disabled the firewall , just so i would be sure its aint a F.W problem and still , not working .
I recently installed VMplayer on my Win 7 machine, and I installed Win XP on the VM. So far everything seems to work fine. However, on my home network I have a Linksys NSLU2 mini network server which has a flash drive plugged in that contains my files that I access from any of my home PC's. No problem accessing it from the Win 7 machine, but when I try to setup a "new network place" on the XP system, I get an error telling me that the address is not valid.
View 8 Replies View RelatedMy host OS is Ubuntu 12.04 and I am running a LAMP stack there. I have several Windows virtual machines (XP and Windows7) running in Virtual Box so I can test IE6, IE7, etc..
I frequently move this laptop between a few wireless networks and sometimes I am without an internet connection. I pause and save the VM execution state. Regardless, I want the virtual machines to be able to access the sites I am hosting locally on Ubuntu. The virtual machines do not need regular internet access. On the host I can point the browser at localhost or any subdirectory that apache is serving and view pages I've set up already. What is the best configuration for this?
Should I use Bridged or NAT virtual adaptors and should the guests use static IP's or DHCP ? I've also considered using ad-hoc networks between guests and host, but I think this will require that the host disconnect from any other networks (with internet access).
it was possible to install RSA Authentication Manager server into the ACS 5.3 Virtual Machine ?
View 0 Replies View RelatedI have a host machine (Laptop, Win 7 Home Premium x64) running Windows 7 Ultimate x64 on VMWare Workstation 9. I've got this system set up for UMDF driver development, because I need a target machine to debug drivers on. However, because I'm developing drivers for Win 7 (x86 and x64), I cannot connect to the virtual machine on via a simple network connection. Connection methods are outlined here.
I have tried a few different pieces of software (mostly Eltima software), and have Google'd every combination of phrases that I can think of. I can't find any information on this anywhere. I don't just need to share data between the machines, I need a more "physical" connection.
Does any know how to do this, or if there's another (preferably more simple) way of doing it?
I have a PC on a crowded network that cannot handle much more bandwidth usage.I am now going to have a tons of transferring to do offsite so I added a second internet line just to deal with the influx of file transfers.I tried a dual WAN setup on my router and the performance was not improved (if it was nobody noticed it) so I said forget that idea, I only need to do these massive transfers from 1 PC so I will just add a second NIC to the machine so that the 1st NIC can maintain local network functionality and the 2nd NIC will be just for internet traffic (sending files up/down to offsite location) Essentially I just need NIC1 for handling local network, connecting to exchange etc. and NIC2 to handle files transfes to offsite location through seconday internet line.So now I have a desktop PC with two NICs. One of them built into the board, the other a pci add on nic. they are both 10/100
On nic1, there is a connection to my network 200.200.1.X which is the internal network for Exchange, local files transfers etc. This is the network i have always had connected and I have no problem connecting to my exchange server etc. (my server is providing dns/dhcp/wins/AD/MSE for the entire network)so I installed a secondary NIC and a secondary network line to the NIC2 on the machine.I set it up with an IP, a SN, a gateway and a DNSI removed the gateway from the 1st NIC.SO then I tried adding a gateway to BOTH of the NICs..This allows me to do EVERYTHING I want, however when i go to whatismyip.com and get a result, the IP it is giving me is NOT either of my static IPs (each network has a seperate internet line with a static IP). Not sure where this IP is coming from, but if i tracert google.com it says I am going out through the primary adaptor.The new IP from whatismyip.com makes no sense to me as it is not either of my static IPs, however it is very close.Would this be a situation where my ISP see's I have 2 gateways defined so it generates a 3rd external IP for some reason? Never heard of this but i am no guru.essentially I just need NIC1 for handling local network, connecting to exchange etc. and NIC2 to handle files transfers to offsite location through seconday internet line.
I have an ASA 5505 i have uploaded updated clients to the ASA, when a user connects to remote.company.com either via the portal or an existing Anyconnect installation, vpndownloader downloads the new client to the machine and installs it.
My question is, where does it store the new installer on your local machine?I tried searching, but i just get a bunch of crap of where to illegally download anyconnect, instead of anything useful.
I have a WLC 2006 running 4.2.130 code with AP1020s.I also have several users that have VMware machines that run various flavors of Linux, etc Virtual Machines on Windows XP Pro.
The Windows XP works fine on the wireless. It is the VMWare Virtual Machine running the Bridged ethernet connection that have problems.
The problem is that the Virtual Machine doesn't get a DHCP IP address from the wireless network.
If the user plugs into the wired network all works fine.I have done some captures that show the DHCP requests going out with the MAC address of the wireless client, but no DHCP replies.
It looks like the WLC is seeing the additional DHCP requests from the MAC address of the wireless adapter and dropping them.The same DHCP server (different scopes) are used for both wireless and wired clients.
The DHCP server shows NO activity when the Virtual Machine tries to get a DHCP IP address.The DHCP server is a Cat 6500 running IOS v12.2(33)SXH. DHCP activity was monitored using debug IP dhcp server events/debug IP dhcp server packets. The VMWare Workstation tried is 6.02-6.04.
I have configured vpn filtering on all my l2l vpns. I have restricted access from remote to local resources only to specified ports. It works perfectly.But I want to have also full access from local to remote networks (but still preserve restricted access from remote to local). As I now VPN Filter works bi-directional with a single ACL. So is there some way to open all traffic from local to remote and still restrict remote to local traffic? ASA 5520 8.4(3)
View 4 Replies View RelatedI have a number of 1552e APs connected to a 5508 WLC. We are using local MAC filtering to enable the 1552's to connect to the WLC.
I have a several more 5508's in different locations, and can be used for back-up in the event the primary WLC fails.I have the primary WLC, a secondary WLC and a tertiary WLC loaded into each the 1552's HA tab.
My question concerns the secondary and tertiary WLCs... do I have to load all the MAC addresses in each of those as well in order for the 1552's to connect? If yes, is there an easy way to copy the local mac filtering from the primary WLC and load it into the other WLCs ?
I found an interesting manual at this forum for blocking websites whits local content filtering. After I've modified the variables to get more details, I stopped at on question. My current Problem is "zone-pair.
zone security Z-SECRUTIY-SOURCE
zone security Z-SECRUTIY-DESTINATION
zone-pair security ZP-SECURITY source Z-SECRUTIY-SOURCE destination Z-SECRUTIY-DESTINATION
service-policy type inspect CM-INSPECT-TRAFFIC
[code]...
I have a 2911 router inside our network with both DHCP and DNS enabled. Everything works fine except since we use this router we are not being able to go to the network neighbourhood in Windows and look up machines by name (or typing \diskstation for example). Connecting by IP works fine but not by local machine names.
View 10 Replies View RelatedI am working on Cisco 3550 switch on a certain requirement. I have got an access point connected to the switch and few mobile phones connected to the access point. I get the list of mac addresses connected to the switch ( Both access point's mac address & the clients addresses) by "show mac-address table dynamic" command. However, i am unable/confused to get the output of the following scenarios:
1. I would require to export the mac address from the switch to the local machine in any format (May be by using an SNMP tool, if available) so that the same needs to be used in my C# for development.What would be the way for the same ?
2. The mac address in the mac address table doesn't get updated dynamically. (Eg Scenario: A wifi client gets connected to an access point which inturn is connected to the switch, the mac address of the client shows up in the switch table. However if the client is disconnected, the client's mac address would still be displayed in the switch table )
I have come across articles mentioning that URL Filtering can be implemented by using ASA 5505 with URL Filtering Servers. But Websense and other Web Filtering Servers are paid ones ? Are there any free solutions available ? What exactly is N2H2 ? The reason is I don 't want to increase the CPU utilization of ASA by implementing URL filtering within the device. If I have around 30 nodes which connects to the internet via a 2Mbps line through ASA 5505 and if I want to block around say 10 or 15 URLs , will it increase CU utilization beyond permissible limits ? Currently the CPU Utilization is around 10 - 15 . Here's the infrastructure setup .
------------------------------------------------------------
Nodes -->Switches-->ASA 5505-->Internet
-------------------------------------------------------------
I have a strange error on my home network that I cannot find a solution to.I have an Huawei SmartAX MT882 from TalkTalk acting as a modem connected to a D-Link DSL-G624T acting as a router/switch. Connected to the D-Link I have a Windows 7 Pro machine (64-bit, SP1) and an XP (home i think) machine (sp 2 i think).The SmartAX modem is set up to perform DHCP and DNS relaying and the D-Link has DHCP turned off and DNS relay turned off.The Win7 machine can access the network, get an IP address and access the internet without problems, regardless as to the status of the XP machine.The XP machine can access the network, get an IP address and access the internet with no problems ONLY of the win7 is powered up. When the win7 machine is off, the XP machine seems to drop about 25% of the ping packets between it and the D-Link router and has no internet access (because of this i assume). [code]
View 8 Replies View RelatedNew Win-7 machine set up. I used the printer set-up wizard to install a networked printer in the new machine with absolutely no problem. Proved it would print from that machine.Now, I get a call informing me that her old XP machine, which had been printing to the network printer with no problems, will no longer print.Documents go into the print queue, but they don't get printed.No error messages show up.I did some messing around via remote access, and finally removed the printer with the intention of reinstalling it.Scanning for network printers turned up several redundant instances of the same printer with different names. Some are identified as "invalid" some a "access denied". Bottom line. I can't get any of the selections to install.On the Win-7 machine I did find a window that indicated that the printer is designated as being shared, but I didn't explicitly set it for sharing when I installed it. Also, I somehow got to a window that told me that for printers that were to be shared with other versions of windows I could optionally install drivers to support such machines. Didn't have the driver disk handy and took the window down. Now I can't even find it again.I need sorting this all out.Part of the problem is that out there in "network land" there are redundant remnants of previous installations that are being remembered inappropriately.
View 11 Replies View RelatedI have a network problem. My windows 7 machine is not detecting win xp machine whereas win xp machine is detecting win 7 machine. They are in the same workgroup named Home. And the networking system is set to work. I have left the homegroup I was previously in. I enabled file sharing for devices that use 40 bit and 50 bit encryption. On XP I have enabled NetBios over TCP/IP. File sharing is enabled on both computers. I think it's something obvious as both instalations on different computers are really fresh and both windows haven't been tampered with.
View 12 Replies View Relatedi'm trying to setup a local DNS server to manage small office local-only domain names for our servers. i have the DNS working properly (resolving local machines and using the ISP dns if it can't). so i put the DNS server ip into the "Static DNS 1" field of the router settings. the other 2 static dns fields are empty.the problem is that the router is still using the ISP dns server as the primary and my local dns server as the secondary. i verify this in two places. first, if i go to the "status" tab, DNS 1 shows the ISP server while DNS 2 shows my local DNS server. secondly, if i connect to the wireless device with a linux-based machine, the /etc/resolv.conf file shows the nameserver ips in the same incorrect order.
View 1 Replies View RelatedI just upgraded to the Belkin N750 DB router from the version just below it and couldn't get the wireless card (Ralink RT2760) in my daughter's dual-boot WinXP/Ubuntu 10.04 to connect to the WPA security setting (WEP only) on the Ubuntu side. There is an updated driver, but it's way above my Linux skill set, so instead I just disabled security completely, and used the MAC Address filtering to add all of our household devices.This solved her connection problem, but I am wondering if there is any danger to this method that I might not have considered
Originally Posted by BelkinMAC Address FilteringThe MAC Address Filter is a powerful security feature that allows you to specify which computers are allowed on the network. Any computer attempting to access the network that is not specified in the filter list will be denied access. When you enable this feature, you must enter the MAC address of each client on your network to allow network access to each. To enable this feature, select "Enable MAC Address Filtering". Next, enter the MAC address of each computer on your network by clicking "Add" and entering the MAC address in the space provided. Click "Apply Changes" to save the settings. To delete a MAC address from the list, simply click "Delete" next to the MAC address you wish to delete. Click "Apply Changes" to save the settings.
Setting up Web Filtering on Cisco881 sec K9 router using CCP.
At the moment every user on the domain got blocked by the rule that i set up on the Web Filter (just using the wizard and choose default category). What i want is to separate users so that specific user can have full access while other user get filtered by the category.
And Yes I want to configure this using CCP.
I've a new Dlink DIR-632. All ports snif from outside are answering stealth by default. And the port forwarding feature works good.The problem is that I would like to allow a trusted net IP to reach my computer, whatever the request may be (whatever tcp/udp and on any ports). A kind of DMZ just for a precise IP. I tried the inbound filter feature. I've choosen allow, and I've put the remote IP start and end the same IP. It has been added correctly to the list. However, this IP still doesn't seem to be able to access to my computer on any port unless it tries on an already forwarded port.
View 1 Replies View RelatedI tried to find an answer to my issue however came up short. Did find,url... but that for a 600 not 601. I have "Mac filtering on and to only ALLOW the addresses below" however, it allows any computer, even if i do not have them listed.
View 3 Replies View RelatedI have dlink dir-600 router and I want to block access to website [ URL] for only one PC connect to router. i can either block web access to both PCS connected or block entire web access to one PC.
View 1 Replies View Related