In control panel networking, I'm getting "Wireless Connection Unavailable". Device Manager reports that the card is working & is enabled. Netgear Configuration panel shows that the card is scanning & transmitting OK but is not receiving a signal. Router wired LAN connections are working OK but it appears that the router is not transmitting.
View 1 RepliesMy Verizon USB connection to the internet, suddenly stopped connecting to napster. Prompt says: "Server is unavailable at this time." No one at Verizon has a clue about fixing the problem, which Napster says is a Verizon connection problem..What to do??
View 1 Replies View RelatedI did a System Recovery after my computer had the virus that redirected me to a pop ups and different websites every time. After System Recovery I no longer have internet connection on the computer I used. All the other devices and computer can access my router but not the computer that I've used System Recovery on. I looked at Device Manager and all of my Networking Devices are working properly. I even looked at Wireless Zero Configuration and the Startup type is Automatic and the Service Status is Started.I go into Network Connections and my USB Adapter has an red X on it. I right clicked properties and looked at wireless networks and the preferred networks is grayed out[CODE]
View 3 Replies View RelatedAll my other stuff is connected to the internet (PSP, laptop, iPod) wirelessly but my computer can't seem to detect any networks at all.
View 19 Replies View RelatedRegion : Sweden
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0_1.1_up(120926)
ISP : HessleholmNetwork
My TD-W8968 has begun to freeze up. It had been running for about two hours before this happened. It's a "slow" process that starts with the web interface being unavailable, i'm unable to connect to the modems web interface.And at about the same time it becomes impossible to connect new devices to the wireless network. Right about this point i did a speed test over the modem and performance was abysmal.It was so slow that my web browser believed that it was offline! But i was able to re run the internet speed test once more before it totaly locked up! At this point it was impossible to use the TD-W8968.
This was the,, i don't know,, perhaps the fifth time it happened in a row. It has been running perfect for two months before it began acting up like this.I have done a reset of the modem, didn't solve the problem.I have also done a reflash of the firmware, i've had the latest firmware since i bought the TD-W8968. But the reflash didn't solve it
My WRT120N router doesn't have Internet Access Policy when I access it.
View 2 Replies View Relatedwhy i can't add a new policy. I can't fillin a policyname or change the status from disable to enable. I have model V2 with firmware v2.0.03 build 007Jul 2, 2009
View 3 Replies View RelatedI have the new E4200 with an attached 750GB hard disk.All works well, however the media server becomes unavailable most of the time and renders the device useless.
I can connect to the Media Server from my xbox and laptop for an hour or so, and then all of a sudden it is gone. The only option I have is to reboot the router to bring it back online however not all of the music and videos are shown on the media server (yet).I uploaded quite a bit of music and video to the hard disk, I can initiate a scan but after a while the media server becomes unavailable / cannot connect to it.
I purchased a New Netgear N150 wireless Router 2 weeks ago and now my internet on my laptop keeps going down.. As Far as I can tell When it drops its still connected to the Wireless network.. it just says local only and Gives me the limited connectivity warning.. When I diagnose the issue it tells me a number of different things and it tells me to renew the IP settings and sometimes that will work and sometimes not.. The laptop is a HP Pavilion DV9000 with all original hardware.
View 1 Replies View RelatedI have a Netgear wgr614v7 wireless router that has been working perfectly for a couple weeks now, but I have suddenly run into a problem. For some reason, I can now only connect one laptop at a time to the networkWhen I try to connect, it says, "Windows was unable to connect to [network name]". When I try to connect with my Macbook, it says "network timed out". Before, I was able to connect all three without any problems.
View 4 Replies View Related how to block a dynamic wireless IP address or the SSID of a wireless connection from accessing my router?
I have 2 people that have somehow managed to get access and i wish to discard them so they cannot reconnect. My wireless router is a Netgear WPN824 and i am running Windows XP.
How do I set up a wireless internet connection for my laptop? The router is a Netgear WNDR3400?
View 1 Replies View RelatedI am having trouble with my wireless internet at home, i am using a dell inspirion with windows 7, and an ipad, my router is a Netgear DGN2000, what happens is that the connection is intermittent on all the devices when using the wireless connection but no problem when using a direct connection.
These are the spec when it is working:
Windows IP Configuration
Host Name . . . . . . . . . . . . : Ericise
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No[code].....
My internet went down temporarily last week and ever since my computer has not been able to maintain a connection. It will pick up the signal intermittently but produce painfully slow internet and then promptly lose the signal all together. The wireless connection is working perfectly on laptops and smart phones, even when in the same position from the router as my PC.
Router: Netgear Dg834Gv3
Wireless Adapter: Netgear WG111v3 USB
Computer: Dell Vostro 200
ISP: AOL
How do i configure my netgear router to my samsung blu-ray player to allow wireless connection?
View 2 Replies View RelatedI have a NetGear WNR-1000 wireless G router. I currently only have 1 computer hooked up but I have had 3 computers hooked up to it before. It doesn't matter what internet it's connected to or how it's connected to the modem itself. I have had DSL and Cable hooked up to it and I am currently using it as a secondary router behind my roommates old Wireless B router. He currently has all of his things hooked up via ethernet and wirelessly to his router. So, im download the xirrus wifi inspector thing. It doesn't matter the OS either. I've had XP sp3, vista, and 7 all hooked to it and it's the same all the way around and it doesn't matter the kind of wireless card either!
View 1 Replies View RelatedSo the other afternoon we had a freak power outage, my PC was on and connected to a surge protector. So once the power came back on, literally like 5 minutes later, I rebooted my PC and have had Wireless issues ever since. My PC is custom built with a Netgear WG311V3 PCI Wireless card in it. When I boot up, it tells me I am connectied to our wireless network, but no websites will load. I check for wireless networks but my PC tells me none are in range. I have had this issue before so I goto Network Connections and Disable Wireless Network Connection 2, my wireless card, and then when I goto Enable it I get this error: Connection Failed.
View 9 Replies View RelatedI have my internet hooked up to a DSL Modem and a Wireless Router. But I had configured the Wireless Router wrong that I couldn't connect to it using a WiFi. I was going to reconfigure it but the Netgear Router was outdated that their reconfiguring URL no longer existed. So I went out and got a *NEW* Netgear Router. Prior to the *NEW* Router I had a Laptop and a PC connected via DSL Cable connected in the Wireless Router. Now with the *NEW* Router I had just purchased I connected everything just like I had done with my previous Router. Wireless Connect works great but I can't connected using the DSL Cable connection. It does not respond. I tried connecting the cables to different ports but it didn't work. My PC mainly needs the wired connection cuz it's where I play my Online games. I tried playing with my Wireless connect but it lags very bad. How to get the wired connections to work? Netgear N600 Wireless and Dual Band Router
View 3 Replies View RelatedMy dad is using a netgear router DG834G V2 and has no problem until recently. He got a new phone and wanted to connect wirelessly but couldn't remember is network key. After playing around with things he's obviuosley changed something and now has no internet what so ever.
I've tried plugging in the eternet cable and accessing 192.168.0.1 but can't see any problems there. When i am able to get a connection it's local only and Internet explorer can't display web pages. And when i unplug the ethernet cable it doesn't always find the wireless connection, and if it does find it, then i have the same problem as when the lead is plugged in.
His ISP is AOL although he doesn't always access the internet via aol, he'll use IE and i'm trying to get him to give firefox a go.
I have tried disabled both windows firewall and AVG firewall and individually but still keep getting the message internet explorer cannot display webpage.
Windows IP Configuration
Host Name . . . . . . . . . . . . : Dave-PC
Primary Dns Suffix . . . . . . . :
[Code]....
I just added a wireless router netgear wgr614 and I secured it and it worked for one day and then after that no internet connection. I've rest and unplugged both the modem and the router and still nothing.
View 1 Replies View RelatedI'm using is the Netgear WNDA3100v2.What happens is when I attempt to connect to the internet I have to reset the adapter multiple times before it even recognizes my internet. And then once that happens it takes a few more tries to actually connect. And when I'm connected the speed is fairly decent (around 15-30 Mbps). Problem is, every 5 minutes maybe even less, I disconnect. Then I have to go back through the process of restarting the adapter and whatnot until I reconnect. I've been dealing with this problem for a few months now and have neglected to post about it anywhere because I didn't think it to be this unique.
I have tried just about every other "solution" I could find on the problem and none have worked. Also, if this says anything, I have a laptop setup literally 1 foot or less from my desktop and it connects perfectly well and good using the same adapter. Also I recently purchased another adapter (Linksys AE3000). I figured this might solve my ailment but of course, the same thing happens as the Netgear, except possibly worse. And that adapter works fine on the laptop as well. I also just yesterday completely reformatted my computer hoping it would work, but of course didn't. [code]
Moved into my grandparents for the time being. They have a DSL network...not sure how fast, but it seems very slow. I got a new computer and had to download CS:Source again over steam. It took all night to download and now when I try to go find servers none show up
They have a tiny motorola dsl router. Not sure on the model number as some of the numbers o the sticker have faded away. I hooked it up to my Netgear WGT624 v3 wireless router via the gygabyte 54mbps wireless pci card.
Can I test the connection to see if it is capable of running online games? I've got my iphone 4 hooked up to the wifi and it runs fine...same with this computer web surfing
I have a Netgear CGD24G Wireless Gateway and a Gateway MA8 laptop with after-market Windows 7 (Vista got a virus, went ahead and upgraded.)Now, when I download 100 MB files on my Xbox 360 (Which is wired to the modem) it will be downloaded in a couple minutes, or less. The other computers in my house (There are plenty, and even more that come and go.) get a blazing internet connection, and most of them are wireless.Now this computer, which had an extremely quick connection as well all of a sudden dropped off, while the rest of the computers remain fast.I've gone to Speedtest.net before and after this occurred and my speed before was around 12 mb/s, and one time around 4 AM was even upward of 25 mb/s, all of these tests were performed multiple times on different server locations. I JUST did the speedtest, and it came back with .4 mb/s, and the UL speed was 2.0. I honestly can't remember what I averaged with it prior to the problem, but it was definitely higher as well
View 5 Replies View Relatedip - Comcast.....
tower card - Creatix CTX404 WLAN 802.11b.....
Router - Netgear WNR1000v2 (supplied by Comcast)
Modem - RCA - DCM 325 (Also supplied by Comcast)
Window XP Pro w/SP3
Security - WPA-PSK
I'm getting in no special order
a "validating identity" or "authorization failed" or "unable to find a certificate to log you onto the network" or "limited or no connectivity...etc..."
I have removed the check in front of the enable box in the Authorization Tab. The only difference I have noticed is that the icon in the task bar instead of a white on red X I now get a Black on yellow triangle...but still no connection...all this after a couple of days worth of **bleep**
How do I configure and set up my desktop to get on my neighbors internet connection with the netgear wireless adapter.
View 3 Replies View RelatedOk so I have a Netgear dg834gb v2 and I have a disconnecting problem on a wireless connection for my laptop. When I am using my laptop, my connection will drop at random moments mostly when I'm playing League of Legends. If I'm not playing it rarely disconnects. It drops for about 10 seconds and comes back up usually, but sometimes I have to reset the router. It only recently started happening and I have no idea why. Maybe it can't handle when I'm playing?
View 14 Replies View Relatedrefers a location that is unavailable.it could beon a hard drive on this computer.
View 1 Replies View Related2 months ago, I bought a RVS 4000 for my personnal use. I recently had fiber with about 200Mb/s in download and there are no router that can handle such speed so I search online and I found the RVS4000 and the new on RV180 ... My shop near my house only had the RVS4000 so I bought it (even if I know that it had some problem and it was discountinued...). I check all the problem online and it was problem on the VPN part... so I bought it.
But since I had it, It seems like my connection was dropping every now and then... so I start to check my installation at home... I check the network error... nothing.. I change my network cable... still the problem...
So I called cisco and they send me another one... so I put it back online... and then... same problem... I ask a friend at work, he tried to understand and tell me it was maybe my personnal switch because it was old... so I change it.... but same problem...
I start to track my bug... I found out that there was a hidden telnet available on the RVS4000 so I enable it to see all the process available...
I made a linux script to see when the router was unavalaible ... and I found out that it was every 30 min... I was able to have at the same time a "top" command on the router in a shell ... I found that a process was reaching 100% of cpu use and the loadaverage of the router was increasing from 0 to 5 or 10 sometime... And my laptop was starting to lost packets... (this is normal because the router isn't able to process the connection)...
I try all the firmware (old and new) I try also to put the router in factory default state ... same problems...
I attached a copy of my screen with the network unavalaible..
So from left to right:
ping 192.168.1.1 (the router)
ping google.fr (from my laptop)
on the top right:
top (on the router)
bottom right:
my script which tells me that if the routeur is avalaible or not
Currently using a netgear WG602 wireless router which i use to connect to my 2nd PC and Iphone, with the Netgear router running from my main PC.I have recently been having trouble with my 2nd PC ad Iphone randomly losing connection and the only way for the connection to be reastablished is to reboot the wireless router. Once rebooted i am able to connect again to the internet with no problems, interestingly enough my main PC never loses connection. Also sometimes when i lose my connection and reboot the wireless router i will have a IP conflict pop up on my 2nd PC however i would i say i get this once in every 10 dissconects and not all the time. Sometimes i won't dissconect at all in a day but sometimes i may dissconect 5-6 times.
View 1 Replies View RelatedI've been trying to connect to the internet all day. Every time it connects, but only with limited connectivity. I run troubleshooting, but it doesn't fix the problem. Sometimes it won't have anything to report back other times it says that the default gateway is unavailable. My laptop is the only device in our home that won't connect, so I don't think it's the router.I think the router is a cisco router, there is a cisco box mounted on the ceiling with a cord leading into it (I don't have access to any buttons though)I live in an apartment building with free internet, so I'm not sure who the provider is.
View 11 Replies View RelatedA few days ago we upgraded LMS to version 4. It worked fine, but after installing patches and updates from Cisco web, the web interface failed and we haven't been able to restore the service.
Service Temporarily Unavailable.The server is temporarily unable to service your request due to maintenance downtime or capacity problems. [code]
I was having some troubles with the LMS client itself (Any job I started would run forever, never finish, never error out, just "running") so I rebooted the server and after a reboot the web interface show up with a "Service Temporarily Unavailable" "The server is temporarily unable to service your request due to maintenance downtime or capacity problems. Please try again later"
View 7 Replies View RelatedI got new internet installed in my apartment, intending to use the same WAP as I did on the old network. The only thing that changed from the old network to the new is the cable modem, which is identical to the old one. Currently, the WAP does not connect to the internet, although I can connect through an ethernet cable to the modem itself. My theory is that the modem is set to a static gateway, while the WAP is not. To try to fix this, I attempted to access the default gateway at 192.168.2.1. Of course, I couldn't remember the stupid password, so I tried different passwords with no results.
Now when I try to access the same IP, it loads for a few minutes, then says 'cannot display the webpage' and gives an option to diagnose connection problems. I know the internet still works, because I can go to any other page I choose. Diagnosis produces the following: 'Your computer appears to be correctly configured, but the device or resource (192.168.2.1) is not responding' (no error code given). Maybe this is a stupid question, but was there a limit to the number of times I could try a password? Additionally, I can't get to 192.168.2.1 on a different computer, on a different network, either. When I try the ipconfig command, the default gateway line comes up blank.