No Interface Access On HP 1810g-24?
Jul 30, 2012
My switch is a HP 1810G-24 - Firmware P.2.2. As I read everywhere that this piece is nearly unbreakable I bought a used one from ebay. When I got it, it had a P.1.1. Firmware, so I upgeded to the latest P.2.2 via 2.1 ...My router is a Fritz!Box 7390 with original AVM Firmware.
Now my problem: If I reset it with the two reset switches to factory defaults w/o connection to my router I can access the managemet interface via Firefox or IE easily. (IP-Switch: 192.168.2.10 - IP-PC:192.168.2.12 - both static)
When I activate DHCP or use a static IP outside my DHCP Range (Range 002-200; IP Switch: 192.xxx.xxx.201) and plug in my cable to the router, I can't access the interface anymore. Even pings get lost.
The HP page is quite reluctant with information and exchanging it is also no option.
View 3 Replies
ADVERTISEMENT
Mar 28, 2012
I am trying to setup a small network For a project. I'll first go over the goal, then current equipment, and what I've done.
Goal is to provide internet access to all, with separate between the groups. The groups are Staff, student, multimedia team, and general use. Reason to separate them is for fileshare, Print/scan, security. A second goal is also to provide wireless internet access to the staff group And general usage. here's the equipment I have.
2x hp 1810g-24
1x asus rt-n66u (dot1q supporting)
2x wireless access points (cisco 1231g and engenius eap150, with a dd-wrt rt-n16 as the access point manage)
Here is what I've tried to do..
I've created four additional vlans on top of the default (vlan1)
vlan10 - staff
vlan20 - student
vlan30 - multimedia team
vlan40 - general use
I then turned port 2 on switch number 1 to a trunk, and trunked it to port 1 of switch number 2.The trunks I have them tagged on both switch.All hosts on the network will mostly be just basic computers/laptops/printers/etc.I've tried a number of methods, but can't seem to get it to work smoothly.I just need all the vlans to be able to reach port 1 of switch 1( the router)
View 7 Replies
View Related
May 16, 2011
OK, so just mooching around in the pages of my switch, a 24 port switch and it has in the logs:
268InfoMay 15 22:43:51NIMInterface 26 is Link Down
269InfoMay 15 22:43:51NIMInterface 26 is Link Down
270InfoMay 15 22:43:51NIMevent(39),intf(26),component(2), on non-existent interface
Now, correct me if I`m wrong but my switch only has 24 ports and two of those (23 and 24) are dual personality jobbies!?Where the hell is port 26? Where did it come from? and why did it need to show up only for the switch to realise that it doesn`t really exist?
View 2 Replies
View Related
Jan 8, 2012
i am trying to daisy chain 2 pro-curve 1810g 8 port switches.i got the cable i need to connect them but i just want to know what kind of settings i have to change on the switches to have it run as best as it can.
View 17 Replies
View Related
Apr 10, 2012
I wanted to know if I can somehow setup my network to use a proxy for all connected devices?
For example I can go into Firefox proxy settings and setup to browse using proxy. Is there any way to do this at the router or switch level to not have to configure every device individually I have a wndr3700 router and a HP procurve 1810g switch and am thinking of building a pfsense box.
View 8 Replies
View Related
Jun 8, 2011
I have a brother mfc-665cw connected wired to my netgear router.
I assigned a static ip address to the printer From a desktop (windows 7 ultimate) I can ping the printer and I can print as well ,,,means desktop can talk to the printer.
But whenever I typed in the right ip address for the printer in 3 different browsers (error message: page could not be displayed!!!!)
I disabled the firewall and Antivirus (Micro Trend) same problem persisted .
View 3 Replies
View Related
Jun 6, 2011
I can't seem to be able to access my wireless routers settings on my iMac, whenever I type my router's ip adress in my browser's adress bar it's unable to connect. According to the network settings menu my router's ip adress is 78.21.0.1, I don't know if that has anything to do with it.
View 8 Replies
View Related
Jun 12, 2013
Few week ago we purchase Cisco ASA 5505 as replacement broken Dlink DFL800. I try to configure all setting like it was on DLink, and all work fine with exception of one thing.
We have some resource like terminal server, that placed in internal network with configured static nat on ASA, some users use it from internal network and some from internet, but both of them use one DNS name for it like terminal.%company_name%.ru. all work fine for internet users when they try to reach server from internet with but internal users unable to use external ip, they even unable to ping external ip address from internal network. Yes i know that one way to solve this problem, is just to use internal DNS server so it can resolve terminal.%company_name%.ru in to internal ip address, BUT i want to know does exsist any way to "loop" trafic this way?
In DLink config there was 3 string in config that solve this problem
<IPRule Name="RDP_Terminal" Action="SAT" SourceInterface="any" SourceNetwork="all-nets" DestinationInterface="core" DestinationNetwork="InterfaceAddresses/wan1_ip" Service="rdp"
[Code].....
View 5 Replies
View Related
Jan 12, 2013
How to apply access list on Vlans ?
my Scenario is
13 Vlans in cisco 3560 switch (Vlan 10,20,30........ 130)
vlan 10 ---- ip range 192.168.10.0/24 interface vlan 10 ip add : 192.168.10.1
vlan 20 ---- ip range 192.168.20.0/24 interface vlan 20 ip add : 192.168.20.1
here i want to block vlan 10 access to vlan 20 i created extended access list deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255
and applied in interface vlan 10 as out now i cant able to access any host in vlan 20 (host 192.168.20.1) but i can able ping vlan 20's gateway 192.168.20.1
View 3 Replies
View Related
Apr 21, 2012
I am using the x3000 as a modem and router, and I managed to set up the device yesterday through the web interface (192.168.1.1).However, after less than 24 hours of continuous usage, I cannot access the interface for some odd reason. I tried using the disk that came with the device but the software reports as if I am not connected to the router. I tried pinging 192.168.1.1 and I get >1 ms so that confirms the device is active and responsive.
View 1 Replies
View Related
May 12, 2013
Months ago i can enter in the camera interface by using 192.168.1.100 , its correct ip to enter in the cammera ? Now i dont know what is happening i connect the ethernet cable correctly from PC to the camera and i type in the browser : 192.168.1.100 but nothiung happen ?
View 4 Replies
View Related
Sep 10, 2012
Just got my server team to install ACS 5.3 on a virtual machine.Unable to access the web interface url...Nothing happens when i try and access this.how i can fault find this as i have cli access.
View 8 Replies
View Related
Sep 26, 2011
I can access our CSSS 11500 through telnet and a serial connection. When I try the web interface, I get:
CVDM Startup Error CVDM has not been granted the necessary privileges to startup successfully, or another unknown error occurred during startup. Please close all involved browser windows and try again by granting all requested privileges.
View 2 Replies
View Related
Feb 8, 2013
I have 2 WLCs (Cisco 5508) in my network. The primary has 16 Aironet 1261 APs connected. Secondary WLC is just staying there and no APs are associated with it. Everything works fine. I was accessing the controller via a wireless client all this time through the management interface 10.74.15.2 using https. It was working fine.But when I tried to access the primary using the wireled network, I can access the seconday but cannot access the primary. They are in the same subnet and I can ping both of them.
View 2 Replies
View Related
Aug 8, 2011
How can I access the we interface of this switch if it is configured to get its IP address from the DHCP server? Since it is DHCP I do not know what IP address has been assigned to it therefore I do not know what ip address to enter in the browser.
View 9 Replies
View Related
Oct 5, 2012
I need the ssh access on my ASA outside interface and have added
ssh ipremoved 255.255.255.255 outside access-list acl_outside extended permit tcp host ipremoved any eq 22 but this is the log i get from ASA
Oct 06 2012 16:10:04: %ASA-3-710003: TCP access denied by ACL from ipremoved/39884 to outside:ipremoved/22
Cisco Adaptive Security Appliance Software Version 8.2(5) Device Manager Version 6.4(5)
View 7 Replies
View Related
Aug 3, 2011
Our SRP527W is working - internet on and SIP phones on but I cannot access the Web interface anymore. When I try to login from any of the machines around I get a "not responding" message.
Before I get to the stage where I have to reset the whole thing and re-do the configuration completely ? I tried powering off and powering on as well as restarting all the switches etc... but I get the same result.
View 1 Replies
View Related
Apr 15, 2013
I can't accsess web-interface on SF-300-24. My computer is on the same subnet. Can only access by RS232. The Switch doesn't answer on ping either. In the manual it says the switch has ip-adress 192.168.1.254.
View 4 Replies
View Related
May 22, 2011
I recently purchased a used 2716, and I just can't seem to access the web interface.i have a Cat5e cable running from my router to Port 1 of the switch. I have my laptop connected to Port 16 via a Cat6 cable.
I have internet access both on managed and unmanaged modes, so that's working just fine. I can't seem to access the web interface however. I've tried both IE9 and FF4.
I followed the instructions to hold down the "Managed Mode" button for 30 seconds, and then wait for the switch to reboot. I've done this a few times just to be sure. This should reset it, but when I try to access 192.168.2.1, it just tells me it cannot access this page.
View 15 Replies
View Related
Dec 22, 2010
I have a problem in my Cisco 1841 in Virtual-Access Interface all interfaces is UP Except Virtual Access is Down . [code]
when i want recover the virtual access to up ,should i do shut & no shut to the ATM interface.What is the cause of the problem, and how I can solve this issue?
View 2 Replies
View Related
Jan 21, 2013
Used to access the FTP server using "My computer" as some reason we cannot use the IE explorer to direct access...However, under the Windows 8 enviornment, it just prompt out "No Such Interface Supported" and cannot direct open the file... but only can copy/copy to folder etc...
View 1 Replies
View Related
Apr 2, 2013
I have a router in front of a few firewalls on an internet link. All traffic from the inside network must go through one of the firewalls to get out through the router and similarly there is a dmz on one of the firewalls.I am trying to make sure the router is fully hardened.Should I apply an access list on the outside interface of the router along with the access list for management access?
View 11 Replies
View Related
Mar 31, 2011
I cant access the advanced user interface web page through the IP address 192.168.2.1. It's a belkin N router that worked for the first few days but now we can't access the Internet wirelessly if we shut the laptop down and reboot. Belkin talked me through every possible way to connect to AUI but no joy. Even tried using firefox, which worked once but we then lost connection again. Getting frustrated now. May take router back to the shop as it's only ten days old.
View 1 Replies
View Related
Feb 24, 2013
I have linksys WAG120N model with 20.0.0.2024 LAN IP and i connected it with SpeedTouch 510 dsl router(IP 10.0.0.138) that act as gateway to internet , i have configure 1st ethernet port on my linksys asWan with static ip 10.0.0.10024 ,10.0.0.138 G.W & configure DHCP in it, the problem that i can't access to my linksys web interface (ip 20.0.0.20 or 10.0.0.100)via 10.0.0.0 network.
View 3 Replies
View Related
Dec 30, 2012
I have a WRT56G router that I'm unable to access the web interface with my desktop computer.I can access 192.168.1.1 using my laptop through the wireless connection.I have a feeling that "something" in my XP Home is preventing me from opening the web page.
View 9 Replies
View Related
Feb 11, 2012
We have a 3745 LNS router, currently there are less number of users connected.when a user dials request authenticated and one virtual-access interface is formed in LNS router.Now the user is disconnected the vpn and connected to VPN again in this case, whether the user is connected to the same virtual-access interface which was assigned before disconnecting or different virtual-access interface is created.
View 0 Replies
View Related
Feb 11, 2013
I have an 1841 between my firewall and the ISP. Three interfaces - multilink to ISP, FA to my firewall, and FA to my inside network. I use the inside interface for configs aand snmp access, etc. Only my ISP-assigned fixed address block will get routed to the multilink by the ISP but I am nervous about the inside interface sitting on my LAN. I know I can remove it, but if I keep it there, how can I set up an ACL so that all traffic from the multilink interface is denied to the inside interface? I suppose another way to think about it that the inbound iface can only accept traffic from its own outside, not from the router.I think this is fairly simple but I don't want to knock down the traffic if I get it wrong.
View 8 Replies
View Related
May 24, 2012
Got a shiny new SG 200 26P which seems to work fine operationally.owever, when I am trying to access the web interface from a different IP subnet, the web brower just times out.If I put my PC on the same IP subnet, it works just fine. From the other subnet, I can ping the switch fine. The default gateway is set on the switch, and from the web interface I can ping and dns resolve other hosts and on the internet. I've tried to create a management profile to 'allow all from everywhere' basically, but still no luck.I'm completely stumped. I've tried to reset to firmware defaults, and I'm now runinng the latest firmware. I woudl suppose that the switch would allow itself to be managed via the web interface from all subnets by default. Any thoughts? The fact that the switch can ping internet hosts makes be believe it's own default gateway and IP are all ok and working.. (and I can ping it from anywhere in my network).
View 4 Replies
View Related
Jul 6, 2011
I had insatalled the ACS 5.2 on Vmware . As per my requirement i need to configure a user to restricted privilege so that he should be able to execute only the below commands on the switch .
-Show ver
-Show interfaces
-Show ip Interface Brief
-Configure terminal
-Interface <interface name >
-Shutdown
-No shutdown
The users should not be authorized to execute any other commands than above listed one .After the configuration i was not able to restrict the config mode commands . Once the user is authoized for Configure terminal access he will have full access on the device. How to configure the command set only to allow interface access and he should be able to apply Shutdown and No shutdown command .
View 6 Replies
View Related
Dec 28, 2010
I'm a networking newbie, but I bought the SG 200-08 switch to do Link Aggregation with and I can't access the web interface. I'm on a mac running 10.7.3, and I've tried Firefox and Safari. I've also tried on a friends PC with Internet Explorer 8.On the mac, I can go into the terminal and can see that the switch has the correct IP address and is seen on both ethernet ports.
View 2 Replies
View Related
Oct 22, 2012
I have been working on figuring out a VPN problem on my companies ASA5510. I was accessing the device via: ASDM, SSH using Putty, and even initially with a console cable (also using Putty) using a computer in the networking closet. All 3 of these access methods worked properly for me.I believe I may have inadvertently changed something as of Friday using ASDM. I am mostly assuming this because, as of yesterday I can no longer connect to the device. I actually cannot even communicate with it (ping the interface I normally use to manage, which I could previously ping). No computer on the same subnet as me is able to ping the interface. The device is still accepting VPN connections, dishing out DHCP addresses and everything else it normally does, but I really need to be able to gain access to it again. I am thinking to reboot the device when there is some downtime, in the hopes that ASDM doesn't save to startup-config and only to running-config.
View 5 Replies
View Related
Mar 11, 2013
This is a working example using static. But it doesn't work with the dynamic interface or I'm doing something wrong. Need to get rdp access to my laptop.
ASA Version 8.4(5)6
!
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]...
View 1 Replies
View Related
Dec 3, 2012
I'm a networking newbie, but I bought the SG 200-08 switch to do Link Aggregation with and I can't access the web interface. I'm on a mac running 10.7.3, and I've tried Firefox and Safari. I've also tried on a friends PC with Internet Explorer 8.
On the mac, I can go into the terminal and can see that the switch has the correct IP address and is seen on both ethernet ports:
? (192.168.1.254) at 2c:36:f8:4f:fc:8 on en0 ifscope [ethernet]
? (192.168.1.254) at 2c:36:f8:4f:fc:8 on en1 ifscope [ethernet]
either accessing the web interface or with setting up the Link Aggregation on the switch some other way.
View 4 Replies
View Related
