One min internet was working then 0 Thought might have been an update so tried a system restore no luck.other pcs are connected to router wireless mine is a wired connection no network access belkin 54g nivadia n force network controller. [code]
View 14 Replies
I need configuring my N900 router to be able to use Microsoft's Remote Desktop Connection to get into my computer from a client's location. I also want to be able to host websites I'm developing so my clients can see the changes before publishing to their website. I have not been able to find anywhere what settings to set to what in order for these two things to be available to me.
View 2 Replies View RelatedAs per settings menu, I tried to give it an IP address but the new address is not accessible for further configuration. When I connected to the router it status changes to "unidentified network".
My primary network address range is 192.168.1.1 to 192.168.1.10. So I gave address to belkin as 192.168.1.100. But I can not access this address from both primary and belkin network.
I am working with MS Windows 2008 R2 and a Belkin F5D8635-4v1 router.
I have already set up a dynamic IP address which points to my router at home. In my home network I have multiple PC's that I would like to access from the internet. I would like to achieve this without needing to change my port forwarding rules on my router each time...
My thoughts are that I use a single dynamic IP address pointed to my router. My router then forwards to a server with some sort of software that can then forward to the correct PC based on the host name.
So I have 3 domains set up all pointing to the router's IP address:
dest1.domain.com -> 41.xxx.xxx.45
dest2.domain.com -> 41.xxx.xxx.45
dest3.domain.com -> 41.xxx.xxx.45
The router is not smart enough to redirect by host name, so it will just forward everything to 10.0.0.20 The server based at 10.0.0.20 must then have software to now redetermine the target based on the host name. The rules would be set up as follows:
dest1.domain.com -> 10.0.0.22
dest2.domain.com -> 10.0.0.24
dest3.domain.com -> 10.0.0.26
Setup N600 DB as an access point using the most recent firmware,3.03.12? Once I do I'm not able to access the dashboard even through I enabled the remote management option.
View 2 Replies View RelatedDoes the N750 (F9K1103V1) support Guest Access while in Access Point mode? It will not provide an IP address when a guest attempts to connect.
View 20 Replies View RelatedI have an n600 ( F9K1102 v1 , firmware 1.00.09 ). My ISP provides my main router for my network, but I want to use the N600 as an access point, I have activated the "Use as Access Point" feature.Is it possible to still utilize the Guest Access feature in this case?
View 1 Replies View RelatedI'm having trouble accessing the setup page for my Belkin F5D8231-4 ver.2001 router.I tried all of the following ip addresses after hard resetting the router to factory settings: 192.168.0.1, 192.168.0.2, 192.168.1.1, 192.168.1.2, 192.168.2.1, 192.168.2.2,Neither plugged directly into the router with cat5 nor wireless connection made a difference.I tried using a different computer and different browser.
View 3 Replies View Relatedhave netgear pcmcia card need to connect to new belkin wireless access point.
View 1 Replies View RelatedI just say that I'm not brilliant with pcs but I'm able to follow instructions if they are in the consistency of baby food! XD..Well basically I can't access my wireless modem router's settings (2 in 1 device I believe). I managed it once but haven't been able to do it again. I've tried the following:
-Reset router many times.
-Turn it on and off many times.
-reset router while ethernet cable is connected and without.
-ipconfig/release and renew
notthing works!!! I noticed the ip address changed from the default one of 192.168.2.1 to a completely different one...95.175.138.When I turned on my laptop today after being off overnight (and the router) somehow I did managed to get on the settings page again using 192.168.2.1 but didn't last for long. While I did this there was a warning icon next to the wifi icon, but then when the warning sign went off that's when the router's setting page stoped working again.I need to get to the router setting because currently is set to go off when i turn off my laptop which is a bit pointless and change a password.
I recently purchased a new Belkin Play Max N600 HD, much different to my old Billion 5100. I'm only on an ADSL connection but will be upgrading to ADSL2 soon.
Anyway I have a Netgear WG602 v3 Wireless Access Point, and I was wondering am I able to put this somewhere else in the house and have it relay the internet connection to my devices (iPhone for example).
I'm in the User Interface of my Belkin Device but I have no clue how to actually set up this Netgear device to act as an AP. I've changed one thing on the Belkin device, not sure if it'll make any difference. I changed the Wireless Band from 2.4Ghz to 5Ghz hoping that it'll strengthen the signal. I've attached a print screen of how the User Interface looks like in case any of the knowing would need some guide to where things are placed. =/
EDIT: Also whenever I'm downloading it's a bit slow. I don't have the fastest internet only 1.5Mbps (150kb/s) but now I'm downloading at about 50kb, and from my computer at about 70kb. =/ These are at separate times.
I am using a Verizon Fios system at home. I have a desktop pc on the other side of the house from my modem that does not have wireless capabilities. I read that I can use an access point to connect it to my wireless network. I'm not sure if this is true or not. I set up my Belkin N150 basic router as directed to make it an access point. I connected it to my desktop pc on the other side of the house and it does not work. 1. Can this set up work? 2. If so, what do I need to do to get connected? Currently the pc is not even recognizing the router/access pt.
View 7 Replies View RelatedI have the Clear Hub Express (Router/Modem combined) and I am trying to connect a separate Belkin Wireless Router (Model F5D8233-4v1) to allow additional "hard wire" connections. Correct settings required for the Clear Hub Express and any additional information that can instruct me on how to access the Belkin set-up screen if required. The standard 192.168.2.1 is not allowoing access to the Belkin Router.
View 1 Replies View RelatedCan I use my F5D7230-4 as an access point? I need to provide a hardwired ethernet connection to my A/V reciever but not have a wired port in the area of my house. I have an existing wireless router thru Century Link. Could I have the Belkin attach itself to the wireless network and then have a cat 5 come out of one of the four ports to connect my A/V reciever to the network?
View 1 Replies View RelatedI have a home network, using Belkin N750 as main router and wired ASUS RT-N12C1 which was set as AP mode. How can I find the IP of ASUS RT-N12C1 to change channel?
View 4 Replies View RelatedI have a Belkin F7D2301 v1 (01) and I am having the exact same issue. I like to do surveys and I've never been able to access this particular site It does the same thing as the original person's problem. I'm kind of scared to change anything on my router setup because I have several computers on the same router. Will any of this cause the other computers not to run on the router?
View 2 Replies View RelatedEarlier today I put in a password for my Belkin_G_Wireless_CC7A57 router. I had to change something, im not sure what it was. it was like WPA or WAP. now it wont let me go to my router settings 192.168.2.1 in the address bar is how i have been getting to it. now it just takes me to a OOPS google chrome cannot open this web page..... I just want to restore the router to it factory default settings. it will let this laptop on and another one in the house but not an older one we have which runs Windows XP. If i can get to my router settings i will be fine..
View 2 Replies View RelatedI have a Belkin High-Speed Mode Wireless G Router F5D7231-4 and I wish to use it as an access point for my main desktop for my wireless network.
I have followed methods supplied by both Belkin and users and have had no success.
Instructions followed:
- Connect a computer to Belkin router using an ethernet cable.
- Reset the router to factory defaults. The reset button can be found at the botton of it. The reset procedure is given below
- Make sure the router is switched ON.
- Locate the reset button(inside a hole) at the back of the router.
- Use a paper clip, push the reset button and hold it for 30 seconds then release the reset button.
- Unplug the Power cable from back of the router and plug it back again and wait for another 30 seconds.
- Log on to router setup page by typing 192.168.2.1 in the address bar of the browser.
- On the left under wireless click on the option Use as Access Point.
- Select Enable and specify the IP address as 192.168.2.254 and subnet mask as 255.255.255.0 and click on apply changes.
Every time the system crashes whilst applying the changes.
My Belkin "ADSL 2+ Model with Wireless G" router suddenly stopped allowing wireless access this afternoon - right in the middle of use - although the wired connections to that router still work fine. No settings seem to have been changed on the router, and I'm the only one with access. Two phones and a laptop that normally work fine just won't get an connection. The laptop - running windows 7 - says the configuration saved did not match what the router was asking for. I tried another computer that doesn't normally connect by wireless and was prompted for a WEP key - which is odd because the router is configured for WPA/WPA2 AES access with a 9 character pre-shared key. After trying a key unsucessfully I haven't been able to get that prompt up again.Meanwhile I've gone into the router settings and it's definitely set to ask for WPA/WPA2. There are some WEP keys specified if I use the drop-down menu to select WEP, but I can't get any device to prompt me to enter one now.
View 5 Replies View RelatedUninstalled McAfee. Installed Frontier Secure, which uses the Windows Firewall. Received Windows Security Alert message that my Belkin USB Storage Center (where the printer is listed) was being blocked, and would I like to allow access. I selected "Allow Access". Printer has not been connecting all week. No error messages - it tries to connect, and then just stops. Can't find issues with the router or the printer - only with the firewall. Everything looks the way I assume it should - the printer is listed in the Belkin storage center. The Belkin storage center is listed in the firewall. There is no tech support for the firewall. There is no tech support for the printer.
View 4 Replies View RelatedI cant access the advanced user interface web page through the IP address 192.168.2.1. It's a belkin N router that worked for the first few days but now we can't access the Internet wirelessly if we shut the laptop down and reboot. Belkin talked me through every possible way to connect to AUI but no joy. Even tried using firefox, which worked once but we then lost connection again. Getting frustrated now. May take router back to the shop as it's only ten days old.
View 1 Replies View RelatedI have a belkin f7d2301 and I cannot access the startup menu it says startup not found I have remove program and reinstalled it. is the disc bad. i also cannot do auto updates because it can't find startup location.
View 2 Replies View RelatedI have a Belkin F5D7132 Range extender/access point set up as a repeater for my wireless router as its range isn't adequate but this doesn't provide enough wifi signal strength. Can I set my Belkin device as an access point connected by Ethernet to the router?
View 1 Replies View RelatedI have a Belkin G Wireless Router which until recently, apart from a few signal drop-outs, was working fine.A couple of weeks ago, I tried to connect to the internet but despite the icon on my netbook showing that my Wireless Network Connection is connected and has excellent strength, I am unable to open any webpages etc. I tried re-booting the router but it is still not working.
The modem is working fine as I am able to access the netbook if I plug my netbook into it directly and I don't think it is an issue with my netbook as I have the same problem if I try to connect my HTC Smartphone to the internet through Wi-Fi too, eg recognises signal but cannot access pages.The router was permanently plugged in and turned on which I have since heard tends to burn them out so I am thinking it might be an issue with the router.
This problem started happening a few days ago. Whenever I try to access [URL] on my computer that's not physically connected to the router and modem, I keep getting a 403 error:
You don't have permission to access / on this server.
Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request.
Apache/2.2.22 (Unix) mod_ssl/2.2.22 OpenSSL/0.9.8e-fips-rhel5 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 Server at www.facebook.com Port 80 --
but I can access touch.facebook.com and m.facebook.com. If I use the computer that is physically connected to the router and modem, I can access Facebook fine. I've tried using CMDPrompt and releasing/renewing IP to no avail. I use the belkin n150 router with updated firmware and the linksys wireless-g pci adapter with v3 drivers. Never had an issue before up until now.
I have a N300 f9k1002v1 router and would like to add guest access. Unfortuantely I can't find any info on how to do this. The user guide alludes to it but has no details. I also checked out this link: [URL]
since my router setp does not show "guest access" under "wireless" I skipped to #6 as stated. However when I get to #9 there is no "guest settings" dropdown for me to use.
If I want to setup my N+ router 5FD8235-4 V 2 as an access point. How do I go about doing that?
View 5 Replies View RelatedHow do I block access to certain websites with my Belkin F5D8232-4
View 1 Replies View RelatedMy N300 Wifi Range Extender does not let me connect to Internet. I can access other systems connected on the main WIfi network, but I cannot access Internet.I observe as well that all systems connected to the Extender appear, from the main Wifi network, having the same Mac address. I believe that my ISP (Telenet) does not accept that, and that this is the reason I cannot connect to Internet. Is there any way to change that behaviour ?
View 9 Replies View RelatedWhen I set up the Belkin F9K1102 as an access point I can no longer access it via the ip-address and it does not accept the new ip-address I've given it, but takes the ip-address 192.168.2.254, while my network is on the 192.168.1.XXX address series. The only way I can do this is by manually given the router a new address, then manually turn of the DHCP- server and finally move the internet cable from the WAN port to one of the LAN ports - but then the LED-indicator on the router is blinkin red.
View 2 Replies View Relatedi m using belking sufr n300 but i m not able to access internet. if i connect brodband cable directly to computer then i am able to browse.
View 1 Replies View RelatedI have a Belkin Play N600 as my primary and have an older Belkin G+MiMO that I'd like to connect as an access point only. Any step by step instructions of how to accomplish this?
View 1 Replies View Relatedhow to set up a Belkin F5D7230-4 6000 router as a wifi access point. My home set up is the following: Dell Desktop connected by Lan to a Telefonica/Movistar router (I live in Spain), Dell portable .. connected by wifi at the other end of the house ..saying it's portable is a bit of a joke .. it's old and moving it is not an option ! Problem is I don't get much wifi signal on the portable to be able to do anything at all online so after googling on how to increase wifi signal .. worked out that I could set up an access point.. and owning a belkin router have been trying to set it up although I think there is something
I've connected the belkin by cable to the portable and disabled the DCHP and clicked on set up as an access point, set up wifi security and password, but when i am trying to reset the IP address I end up having to reset the router and start all over again.
