Protocols / Routing :: Cannot Copy Xxx - The Specified Network Name Is No Longer Available
Feb 28, 2012
I have Dell machine with Win Xp3 loaded, on my local network (and other computers). I set NIC card "Link Speed & Duplex" to autosense & make direct connection to my modem and works ok.When I plug into the network router I get the 'Cable is unplugged' and no Internet connection.I can change the "Link Speed & Duplex" to 10Mbps/Full Duplex and get intermitten connection. Also when I copy a file from Mapped drive I get "Cannot copy xxx - The specified network name is no longer available".
1. the NIC software is recently updated PRO/100 Adapter NDIS 5.1 driver
2. Although Microsoft has suggested Symantec < ver 4 has had an endpoint problem, I have 10.1.6.6000.
3. TCP/IP Properties are on automatic like the other computers.
View 3 Replies
ADVERTISEMENT
Dec 26, 2011
I just received a blu ray player for Xmas that has an Ethernet connection for streaming Netflix,YouTube, etc. my problem is my router is upstairs and the blu ray is downstairs. I really don't want to run an Ethernet cable from the blu ray to the router. Can I use another router on the same network and have it close to the blu ray?,I have a netgear router just laying around and the main router is a Verizon fios router.
View 4 Replies
View Related
Jun 1, 2011
I have a need to use two routers (Each with different ISP) on my (LAN) office network.I presently DO NOT want to go the (Two ISP's on one router, or Load Balancing router). I Just simply want two routers with two separate ISP's.I will assign the managers workstations to the faster ISP, and other Workstation to the slower connection.And it seems to work, and all resources seem to be available on the LAN, regardless of which (Gateway) Router(1 or 2) I point the workstation to.I assume because all devices are on the same LAN 192.168.0.XXX Is this a proper way to allocate and use two routers on the same LAN?
View 2 Replies
View Related
Jul 27, 2011
I have a local DSL line in our remote office. We are connecting a microwave antennae that carries our main office internet to the remote office.I want to be able to connect both paths to a Layer 3 switch and route traffic through the main office with the router connected to the DSL as a fail-over solution.I would really like to stick with HP Procurve's if possible.
View 3 Replies
View Related
Aug 24, 2011
I'm trying to connect an Xbox 360 to my University's wireless network using a bridged connection between the wireless adapter and the LAN adapter. I can connect to the internet on the Xbox, but not Xbox LIVE. I get an error message stating that my MTU setting must be 1364 or higher. I obviously cannot access the router settings because they are the schools routers and I do not have administrative privileges. So, Is there some other way to modify MTU settings without that access?
View 1 Replies
View Related
Feb 19, 2013
I have a problem figuring out how to setup a home network connection running a VPN. I have been looking through the internet for answers and am still not sure how it all works.
View 9 Replies
View Related
Apr 12, 2012
I had a custom device/computer on my network that was hacked from hong kong. It's one of those things where I seriously think the chinese have built a back door into it when they built it or something because everything was secured and monitored.The device runs it own OS or something like that I guess you could say. It can also run it in standalone mode broadcasting it's own signal. Once I figure this out I may not put it online anymore but thats besides the point right now. When it was hacked I'm pretty sure the port it uses to connect was changed from 80 to 591. When it runs in standalone mode I can connect to it but I am unable to actually access it's proprietary graphic network interface. It sends out UDP every few seconds or so and basically I was trying to search for some type of udp broadcast monitor and have tried using network tools such as netstat, port scanning, multicast, etc on all of the big three OS's because sometimes it seemed to finnicky what it wants to connect to. I've tried to let it connect back to my router again which it seems to do, but is then denied access and I think it may even have a trojan or somethng so I don't want it to that but if I have to to access it again I will.In standalone mode I've it usually trys to connect on 192...5 or 192...7 and I've tried to get through 591, 23, 80 etc. multiple times with no luck.
View 11 Replies
View Related
Jan 16, 2012
I have the modem feeding a router that I turned dhcp off to use it as a switch, I then have the switch feeding a ubiquiti nanostation and a wireless router (to feed house 1). The other end of the nanostation is in house 2 (1000ft away) where I have it feeding into another wireless router to feed that home hard wired and wireless.Everything works but cannot get both to work at same time.
View 3 Replies
View Related
Oct 23, 2011
We have two networks in our lan: 10.0.0.0/24 and 192.168.1.0/24. Actually the networks are separated. The 192.168.1.0/24 network contains some hosts that ip can not be changed. We want redesign the network and communicate with both networks without routers. I thougnt about changing the netmask for 192.168.1.0/24 in 192.168.1.0/22 (1022 hosts) and change IP's in the 10.0.0.0/24 network in 192.168.2.0/22.
View 3 Replies
View Related
Dec 26, 2011
I was working as IT Support in an encoding company. I support over 500 desktop users. my problem is about in entire network because i always encounter hang network in my grave yard shift. Our network system set up have domain server, antivirus server, database server, 4 PC's use as backup servers and 3 unit of network attached storage and approximately 500 units of desktop use for production in encoding. I always experiencing network hanging then after all system will be freeze, so i suggest to shutdown all pc for usually in 5mins then turn on again. In an hour the problem is still exist again and again. I did all possible way to make the production smooth run for my whole shift but still after some hours it occurs again. I dont know what would be the possible reason why the network hangs and stuck up. The network attached storage did not reach the entire capacity, the antivirus server is still updated, the domain and database server are working properly even the PC's use as backup server. There is no internet connection we use in production, so i assure that no virus we encounter in all pc. Is it the cabling? or is it the switches?
View 1 Replies
View Related
Feb 29, 2012
Have a problem connecting my new IPcamera Elro C903IP so I can access it through the internet. Did the camera setup according to the manual. Local access (wifi network) works fine but access through internet remains impossible. IP of the camera is still 10.0.0.110 but I found out that for access trough the internet the IP would be like 192.168. etc but I can't change it properly.I have cable internet and a wifi router Netgear WNDR3700v2.Documentation that I found about port forwarding etc is not clear enough to me. I tried over and over but can't get it to work .
View 2 Replies
View Related
Jan 7, 2013
The question is apparently simple. A network is given, consisting of
- 1 network core switch: HP 5500-EI (Layer3)
- 4 access switches: HP 5120-EI (Layer2)
They are connected in the shape of a star (the core switch in the center)The task is to measure the occupation rate of this network on a per-VLAN basis.
For example : To be able to generate statistics like: During the last week - Monday to Sunday - the netowork occupation with VLAN 10 traffic was 30% and VLAN 60 traffic was 70%.
View 1 Replies
View Related
May 21, 2012
We just had a TEW-72GR router fail and replaced it with a TEW-GR. Now I am unable to get to my domain (mydomain.net) from outside the network. Inside the network, all appears to be fine. I can enter that address and get to the site with no issues.We use SBS 2008 with windows 7 clients.All clients can get out to the web, we can send and receive emails, but I can not access the domain.
View 2 Replies
View Related
Apr 5, 2013
giving unauthorized access and no internet access
Windows IP Configuration
Host Name . . . . . . . . . . . . : KHANBALOCH-PC
Primary Dns Suffix . . . . . . . :
[Code].....
View 2 Replies
View Related
May 29, 2012
my computer, my network connections icon have a exclamation mark (!) and it say i don't have internet access,but luckily i have internet access but i can't remote my computer,
View 4 Replies
View Related
Oct 14, 2012
How to play games network by use wireless TP-LINK I have 2 laptops and one Desktop I want to play games at home, but without the use of the Internet.
View 1 Replies
View Related
Jan 21, 2011
My customer has 3 computer
1- Windows xp
2- Win7
3- Apple
4 new sony laptop.
Vaio would not connect using WEP 40-bit key. Logged into Airport Extreme router with Airport setup utility for Windows from Apple. Updated firmware from 5.1.1 to 5.7. Reset Encryption from WEP to WPA/WPA2 Personal.Connected Vaio on Wifi using WPA2. Removed ethernet cable and connection was good at 54MB/s.Completed Windows Update
View 3 Replies
View Related
Jun 30, 2012
I have set up port forwarding for my WD Network HDD, which runs a Media Server (Twonky). Now, I have tested the ports and accessed it through the internet and it works fine, until... I click a link to open a folder and suddenly I get a "No such page" error thing. I have however identified this problem, it seems that when I go off the main page it re-routes to the original network address, not my IP forward address. For Example if my IP was 82.9.12.456 and the port was 800 i would go to "82.9.12.456:800" and it would load but once I navigate i go to "192.168.0.*:800/*****" and does not load the page. If i then copy and past my IP into the URL it works, but this is annoying.
View 3 Replies
View Related
Jun 2, 2011
I have a Airtel Internet Broadband connection and I have a lan having around 10 workstations. I have another computer which I want to use as a server through which all the internet traffic will pass. The server has two lan cards(one on motherboard and other one is usb).I have connected broadband modem to lancard1(on motherboard) and have connected the lancard2(usb) to the lan switch.Now how to proceed further, so that internet service is available on all the workstations connected to the lan switch.
View 4 Replies
View Related
Apr 3, 2012
I'm studying for a Cisco certification and I'm trying to wrap my head around the routing. I understand how routers work for the most part and how the get updates about networks and how many hops away they are, but I don't get what happens when a router doesn't know the path to a network.
View 19 Replies
View Related
Sep 28, 2011
partition the departmental IP network address block to create a staff and a student subnet. Each of these will be identified by its own network address and netmask. It is university policy that you must be economical with the IP addresses. That is, the subnets must be as small as possible, but they must be large enough to accommodate the maximum number of hosts you were given. Also, it is university policy that the respective gateway router to the outside world should always be given the highest possible host IP address in the subnet. The student subnet should have a higher IP network address than the staff subnet. The network must be able to support up to 60 machines on the staff subnet (not counting the router) and up to 120 machines on the student subnet (also not counting the router).
IP address/netmask
University network address127.158.128.0
University network mask255.255.192.0
University internet gateway IP address127.158.191.254
Department network mask255.255.254.0
Department router address127.158.129.254
Suppose that the network address of the departmental network is 127.158.128.0 (calculated by AND between Dep network mask and Dep router address)I know that 60 machines would use 6 bits for the staff subnet.the netmask of staff would be 255.255.255.192.how can I figure out the the IP network address of the staff subnet.I have worked out the range for the staff subnetwork.
127.158.128.0 - 127.158.128.63
127.158.128.1 = Gateway address
127.158.128.63 = Broadcast address
Now how can I calculate the IP network address of the staff subnet?
View 5 Replies
View Related
Mar 22, 2012
I am trying to map network and copy files to D:BackupSql_Backup?How can I sue this with spaces in my folders
net use R: \000.00.0.00Program FilesMicrosoft SQL ServerMSSQLBACKUP"
cd
echo off
R:
cd
Xcopy . /D /I /F /E /Y D:BackupSql_Backup
net use R: /delete /y
exit
View 5 Replies
View Related
Oct 12, 2011
I have a network using windows home server 1, with 3 computers hooked up to it. Two of them work fine but the 3rd computer cannot successfully copy a file to the network. However, I can copy a file from the network to computer 3.This started suddenly about a week ago and there were no driver updates or anything changed that would cause this. When I copy a file from the network to computer 3 I get about 80mb/second. When I try the reverse, it pauses and after about 5 seconds I get a message saying:There is a problem accessing \serverserverfolder. Make sure you are connected to the network and try again.If I try to copy a small file of a few megabytes it will copy though.
View 5 Replies
View Related
Oct 5, 2011
Basic info: SBS 2008 (64bit), XP-sp3 (32bit) workstations, gigabit switch, SEP. App is Sage Masterbuilder.Network config: Server is 1gb to switch over CAT6. All the workstations are 100mb over CAT5. SEP is set to exclude all pertinent files on both the server and workstations.Problem: The program is called MasterBuilder and does job costing and much more. In the job costing feature there is an option to "Compute" job costing. In version 16.x, when the "Compute" was performed the task was done very quickly. After an upgrade to version 17.x it is very SLOW. According to tech support, our network is at fault since it is a database function over the network.Troubleshooting done: Tech support blamed our network speed (100mb) and switch. We had a Netgear 100mb switch so we replaced it with a GB switch however the cabling will not support GB. Being a managed switch I set all the ports to 100mb except the server port. Even tried the server plugged into a 100mb port and no change. I am confident there are no speed issues on our network. All other programs perform flawlessly. ACAD, Exchange, data transfers and many other high data use programs work perfectly. I updated the network card drivers in the server as well. There are no performance or resource issues on the workstations. I monitored the network traffic at the workstations, server and switch with no issues and about 2.5% utilization during the slow "Compute" process. The switch shows no errors at all, no collisions, no dropped packets, nothing. I also disabled the SEP.
During testing and while the slow "Compute" was going on, I copied a large folder (400mb) from the server to the workstations see the impact on network utilization. As soon as I start the copy process the "Compute" process speeds up to normal and zips by as it should. As soon as I cancel the copy process the "Compute" drops right back to very slow.
View 4 Replies
View Related
Jan 16, 2013
copy or move into local area network? If any software to check which PC or Workstation or Users or IP to do this.
View 2 Replies
View Related
Apr 18, 2011
I am having a problem with copying files onto my Storage device Connected to my WAG320N, the router is up to date with the latest updates and has been reset in an attempt to overcome this problem. I currently have attached a 2TB Seagate External Hard drive plugged directly into the router formatted in NTFS, and using Windows 7 Bit to access the Routers Webpage and the External Drive.
I am able to set up permissions and access control all okay, so some users can see some folders or have access in Read only or Read and Write Permissions, however I have been using the Admin account when accessing the drive which has Read and Write permissions to all Folders on the Drive. I can create a new document on the Drive (Right click > New > .Docx or .txt) and save file successfully and can view from other computers from the network, however I cannot Copy from any of the computers to the Network drive (e.g.. Copy .txt file from Computer to Network drive), I get the Windows Transfer Dialog and it Calculates Transfer Rate for a while before telling me it's unable to and that I can either select Try Again which comes up with the same error message, or Cancel the transfer.The reason why I want to be able to Copy files to the Network Drive is so I can centralise all the Photos, Videos and other files and documents to be shared to all computers on the network.
View 1 Replies
View Related
May 2, 2013
how to copy a cisco ios image from a 3750 to my pc so that i can use it to upgrade a switch on my desk.
View 3 Replies
View Related
Jan 4, 2012
i have 2811 router and i am coneccted via concole so i want to copy the 2811 ios to my PC is that possible?
how or give my the right decument to do this.
* idon't want to use TFTP becuse i have no ethernet connection to the router(only concole)
View 5 Replies
View Related
Feb 13, 2013
I have 2 Chassis 6506-E with sup 720. one of them work properly(Switch1) but another(Switc2) not boot form bootdisk and go to ROMMON mode. I Captured IOS from Switch1 with tftp but I cant Copy this image to switch 2 with tftp.
View 4 Replies
View Related
Feb 27, 2013
It seems I have seen this before (and even done it once a few years ago).. but it has been a while. I have a stack with a Cisco 3750 stack that I have to replace a member.The replacement switch is a 3750X.
I think I have to upgrade the IOS of the older switch to be the same as the 3750X.
Current switch: WS-C3750G-48TS 12.2(46)SE
TO BE ADDED WS-c3570X-48 15.0 (1)SE2
It seems to me there was a way to upgrade the older switch IOS from the newer switch or downgrade the newer switch with the older IOS.I dont have the Cisco account to download updated IOSs.
View 9 Replies
View Related
Oct 30, 2012
I have a Dell Optiplex running XP wired to a Netgear router. My laptop is a Dell Inspiron 1501 running Windows 7. When I got the new router everything programed easily and I could retrieve files from my desktop and print remotely. Sometimes I would have to "refresh" before the laptop would detect the desktop but now it will not detect the desktop or the printer. I suspect that a Microsoft Update did this but just guessing. I went back and deleted the updates that downloaded around the time that this stopped working. I have tried every thing that I can think of to get it back working but can not get it fixed.
View 2 Replies
View Related
Aug 11, 2012
I'm trying to see if I can fix my friend's NAS which apparently has some pretty important data on it that wasn't saved anywhere else. They actually had the Geeksquad look at it and they've come to the same conclusion I have so far, but I figured I would ask the internet before I gave the thing back to them and said Geeksquad was right.
Anyways, they have this 5 drive RAIDed NAS which apparently just stopped showing up on their network. I borrowed it from them to see if I could figure it out. It turns on just fine and my router assigns it an IP address, but the IP address just takes me to a blank LaCie dashboard screen. It's weird because it's clearly running it's web server because it's just a gray background with an empty white box and "(c) LaCie 2010" at the bottom. No content at all.
Additionally, I tried installing the LaCie Network Assistant on my home computer and it says it cannot find any network disks. I've tried the "wake up a device" where I enter the mac address, but that doesn't do anything.
All the lights are solid blue on the front and over all the drives so it doesn't appear a drive has failed or something. Even so, that wouldn't really explain the blank dashboard right?
View 1 Replies
View Related
Apr 16, 2012
I am trying to configure redundancy with SSO and I need to get the same IOS on both supervisors. My issue is that I get an error when I try to copy the IOS from either the sup-bootdisk or the disk0 to the slavesupbootdisk. The Error is Invalid argument.
I have tried also to tftp to the slavesupbootdisk and get the same result.
View 5 Replies
View Related
