We purchased a database program which has 3 licenses attached. This is a small non-profit org. We would all like to be able to use the program from our homes. What is the best way for all to share and update data to the same database? Would we all be able to work on it simultaneously?
View 2 RepliesI have a work program on my laptop (windows7) and would like to access it from my desktop (window 7)
View 1 Replies View Relatedwhat is the easiest method permitting a local and a remote pc to access the same database ? They both have internet access.
View 3 Replies View RelatedI have question about the basics of a high performance application and database server connection to each other. I have two servers, one application and one database server. Both of them are Windows 2008 R2 servers. I would like to connect them. What is the best configuration for quicker communication between them. Is it better to connect them through a network switch? Or directly connect them? Do I need to dedicate one of the ethernet ports on each server to separate their traffic to each other, from the internet connection traffic?
View 5 Replies View RelatedFor my Lan, I have created two Vlan; Vlan 10 = for Users and Vlan 20 = For Database Servers,There are 15 Lan computer/laptop and 5 SQL database server (Dell Server) connected through same 24 port cisco 2960 switch. Means, 15 + 5 port occupied.
I have applied access list on cisco switch to restrict communication between vlan 10 and vlan 20.But My main purpose to create two Vlan is not for any kind of communication or restriction. My main Purpose is that Users traffic do not distrub or choke or affect the Database servers. then what will i need to do for that is VLAN Concept is sufficient for my concern OR I will need to buy seperate Cisco Switch to connect 5 database servers OR Else ?
I work as a System Administrator for a small company. Can i share a CD drive to all the computers in my domain. Or does this require any additional software to do all this. Because i tried to do it normally by sharing that CD drive and by which it was also available in my network. But when i was trying to access that it says "The drive is not ready". We use Windows operating system in our network. I even tried to google this but i could not find any exact answer for this till now.
View 3 Replies View Relatedcannot share internet connection in windows 7?
View 1 Replies View RelatedI need to keep surveillance on two separate remote locations, each on a different continent. They're both indoor locations and have broadband. One of these setups should be fully bidirectional so I can see them and they can see me, while the other location is unidirectional so I can see them but they can't see or hear me. In both of these farflung locations the people there have the computer skills of your average escargot, so it's going to be a complete and utter miracle if they can even figure out how to boot the PC. I would like to provide netbooks to each location and have them automatically launch a fullscreen webcam on bootup. How to get this set up properly so that it works in a foolproof manner.
View 1 Replies View RelatedIs there any way to get reports on voice utilisation on WAN links so that CAC settings can be proactively managed for each location on our CUCM cluster? Our service provider is advising that this is not possible which means that we rely on customer/staff complaints to recognise where CAC thresholds are being reached. Our preference is to be able to run traffic reports (or the Cisco equivalent) as could be done on our previous (traditional) telephony network and provide additional capacity if and when required BEFORE congestion is reached, thus minimising customer/staff impact.
View 1 Replies View RelatedHas a small home network in 2 buildings with 2 wireless routers. He has fiber from the building where the dsl comes into, running up to his house where a second wireless modem is. Both are broadcasting DHCP but I only want one of them to do this. Ultimately I want his server(2008) to broadcast DHCP, but just one of the modems is fine for now.
View 1 Replies View RelatedI know how to connect 2 routers in 2diffrent states using internet.Also which service is used for that purpuse
View 1 Replies View RelatedWe are facing a major issue of VPN tunnel going down very often. I have 7 Site-2-Site VPN connectivity, this works fine for some days and suddently VPN tunnel goes down intermettenly for one or few locations and i need to clear isakmp sa for that speicific tunnel to come up.When tunnel goes down the vpn phase 1 status.....
6 IKE Peer: 125.18.0.38
Type : L2L Role : initiator
Rekey : yes State : MM_ACTIVE_REKEY
7 IKE Peer: 125.18.0.38
Type : L2L Role : responder
Rekey : no State : MM_REKEY_DONE_H2
After clearing phase 1 for specific tunnel the VPN tunnel come up.
7 IKE Peer: 125.18.0.38 Type : L2L Role : responder Rekey : no State : MM_ACTIVE
CINBLR01-SQDR-FIREWALL-00002# sh version
Cisco Adaptive Security Appliance Software Version 8.0(4)Device Manager Version 6.1(5)
Compiled on Thu 07-Aug-08 20:53 by buildersSystem image file is "disk0:/asa804-k8.bin"Config file at boot was "startup-config"
CINBLR01-SQDR-FIREWALL-00002 up 1 day 17 hours
Hardware: ASA5510-K8, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHzInternal ATA Compact Flash, 256MBBIOS Flash M50FW080 @ 0xffe00000, 1024KB
[code]....
This platform has an ASA 5510 Security Plus license.
I have 3 different office location and I need to set up a LAN so that all three are connected and can share info?
View 1 Replies View RelatedI setup one location (business retail shopping center) in maryland (using swann dvr/cameras- will switch to qsee) with no internet available.I setup another location (business auto shop) in virginia (using qsee dvr/cameras) with internet through verizon fios.I have internet through cox at home in virginia which I can view cameras remotely only to one location in virginia.
View 2 Replies View Relatedwhy one of my two offices experiences significantly slower speeds when accessing the web. I'm a complete technology simpleton, so I haven't been able to figure out a logical reason for it. Here's the scenario:
Office 1..................................................Office 2
==========..........................................===========
Comcast Business.....................................Comcast Business
tests at 33 mbps down..............................tests at 7 mbps down
tests at 6 mbps up....................................tests at 3 mbps up
6 CPUs access Linksys SR216 10/100 switch..6 CPUs access 3Com Office Connect Ethernet Hub
switch accesses Comcast modem.................hub accesses Comcast modem
My laptop, and all other CPUs, perform significantly faster at Office 2.
Is it the difference between the switch at Office 1 v the hub at Office 2? I always thought they were sort of the same thing. I know I've taken some of the cables out of the switch in Office 1 and put them directly into the Comcast Modem and haven't seen any improvement.
Why on earth does my laptop perform so much better at Office 2. I've also moved desktops to Office 2 and they are noticeable faster at that location as well. I'm stumped. We access a major company's web site for account servicing, and it is twice as fast at Office 2...while using the exact same laptop.
I work as a systems administrator for a global company and currently right now all my end users which is roughly 300 all use VPN from there office location to dial back into the server or use terminal server. I would like to know how to connect there locations back to main site without using VPN. What would be the cheapest and or easiest method to complete this.
View 1 Replies View RelatedI set up a network drive in my computer that links to an FTP directory on my server.... However all the jpg files are showing the default jpg icon. I want to see a thumbnail of the actual image if possible. Im running windows vista and windows 7. Same issue on both. Also, I tried hard to change the network drive .ICO file.... Tried creating a shortcut and doing it that way.. still no luck.
View 1 Replies View RelatedI'm setting up two separate 5510's at two seperate locations. The client wants two seperate SSL-VPN's; one for the HQ and one for the COLO location. They have a single domain for which I have added a-records to point to the corrosponding ASA's thusly: [code]
My questions is this: do i need to buy seperate certificates for each ASA/fqdn/IP combo? I'm using godaddy to buy the certs. If I do need to buy seperate certs, that makes the installation easier, but may waste $$. If I only need to buy one cert, how do I set it up so that both combo's are verified?
I have VPN connections in between my HO and branch locations. I am using ASA in HO and 1841 branch locations. One of the location is keep on disconnecting, why this is happening as i can see the configurations are identical to other locations.In 'sh crypto isakmp sa' output i can see multiple entries for this particular location, one with type 'L2L' and others with type 'user'.
View 2 Replies View RelatedFirewall ASA5510. I'm planning to get one of ASA5510 for our office in order to secure our network properly, however we have quite specific routing configuration to allow us failover to the remote location (data center) in case of any disaster with our server. I'd like to find out if I can just install firewall between our ISP Ruter and internet and allow traffic to/from Data Centre. In this situation will I have to change routing configuration on Company Router or do I have to do anything with our Company Router
View 1 Replies View RelatedI have 2 dual ASA 5520 devices running VPN at two geographically different locations. What is the best way to do failover between the two remote locations?i.e. can Cisco GSS / Cisco CSM/ACE be used and if so how would this work.
View 3 Replies View RelatedI have establlished VPN tunnle between 2 locations
I can ping accros and access server resources on both LANs The problem is that from one location I can not access Internet
I can not ping by IP,when I do tracert it just reaches default gateway of this locations from other location(office) no problem
I have a small home with two clusters of 2-3 devices which use the Internet - one ground floor, south corner, and the other top floor, north corner. I have a wireless router (Netgear N750) in the ground floor south connected to my cable modem. All devices in the area of the existing router are plugged into it (Cat5 cable). The devices in the top-north corner use wireless to communicate with the down-south router.
Running cable drops is not in scope for me, as we have a finished basement and I would have to blind drill horizontally across 50' of flooring and joists.
Tried running cabling through heat vents using a wireless camera mounted to a cable puller and all I did was discover some areas of my home that appeared to be four-dimensional. Attic not accessible in locations required for cable drops.Tried powerline devices and performance was much worse than wireless - I know that's a major YMMV situation but the Netgear ones I tried had like 5 Mbps connection rates. I also could not connect from other outlets - I have read if you had electrical work installed and have new lines run it can impact powerline performance. That may be the case in my home.
My questions:
A. I have OK to poor signal strength in top-north and top rate is ~ 150 MBps off what is supposed to be 300N router. Would I get better performance if I installed a wireless router in top-north and connected the top-north devices to it? Down-south performance is fine so it's not the cable modem/internet connection.
B. I believe I'd set top-north router up as a wireless client. I've experimented with Tomato and DD-WRT but don't know how to evaluate. Any tradeoffs I should know about?
C. Any networking changes I should consider if I go with such a topology? (MTU, who does DNS, etc). Currently use router as source for DHCP and DNS lookups. Should I limit which router wireless devices may connect with?
I have three computers in a Workgroup and I can transfer files through all the computers properly. However I cant set up permissions to who can access these files. The three computers are Windows 7 64bit desktop, Windows 7 64bit laptop, Windows XP Professional 32bit desktop.
What I tried so far...
Right-click on folder I wanted to share
Click on Sharing Tab
Click on Advanced Sharing>Permissions>Add...>Locations
I only see the name of the local computer, I don't see the two other computers on the network. The window looks similar to this, how I can find the other computers in my network, in the locations window.
I have configured a VPN tunnel between two remote locations using static IP addresses on two RV042 routers. The tunnel seems to work but the problem is that when the two hosts attempt to ping each other only one can successfully ping. One PC with IP address 192.168.1.100 can ping across the network but the second PC with IP address 192.168.2.100 cannot. These are laptops seperate from the intranet used to test the tunnel. Someone had suggested NAT may be the issue so I enabled NAT Transverse on the routers but still no luck. The following is the results from a ping test.
PC 1
ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:
Reply from 192.168.2.1: bytes=32 time=116ms TTL=63
[Code] ......
We installed a new ASA 5515 about a month ago for the corporate office we also have 40 branch locations that feedback VOIP, camera, and Citrix to the corp location. Each of the branch locations have a separate DSL connection with a local provider and all of them are dynamic IP addresses.
The problem I have is that I cannot figure out a access rule to make the voip traffic work 100% of the time what ends up happening is five or six random locations change IP address's every day and I could not figure out how to create a access rule for that so I create a static route with that dynamic IP and then it will change a week or so later. That's a horrible security risk and a lot of manual work.
I have 2 WRVS4400N's installed in our network, one at each end of a VPN tunnel between 2 physical locations. I continue to have issues with the VPN to "Stay" connected, even after purchasing another new WRVS4400N 4 months ago. I can reboot both routers, and the VPN connects with no problem, but hangs up after a few hours / days (no pattern).
I am taking a hard look at the issue now, as about 1 month ago, the newest router "automatically" reset it itself back to factory settings (thus interrupting nearly everything in our network). After contacting support, we reset the router and re-configured it to our environment. It is plugged into a surge protected UPS (yep, I thought maybe a power issue caused the problem, but it's not). Then about 1 week ago, the other/older (9 month old) router lost it's configuration. again, reset it and all works. Including the VPN, but the VPN still works as it did before connects for a while, but then drops and generally I need to reboot the router to get it connected again (clicking on the Connect on either router doesn't work until after a reboot).
Also, in light of the recent "lost configurations", I turned on logging and now I'm getting TONS of emails of log activity, even when the network is idle (no users, no background jobs running).
after rebooting and no inter activity, I get this kind of log, all night long (to me it generally looks like the VPN connection resets and increments by 1... I'm taking a guess that the increment hits a limit someplace and I lose my VPN).[code]
I have a 100MB pipe coming.I have one ASA5505. This is the current backbone to the whole system.I want to send internet to 16 different locations via microwave dishes.So, many problem is my pipe is 100 Mbps , want to cut that large pipes into a bunch of small pipes. Per pipe 2 Mbps.So, I can send this B.W ( 100 Mbps ) to 50 Users.
I have only ASA 5505 and L2 switch for Vlan purpose. I heard by using RADIUS server we can do this but I don't know how to do. IF yes, then some Docs regarding that one.
Im running windows 7 home premium. I have a Dell Latitude D360. My laptop will connect at home or at family's wifi however it will not connect at school. There are two available wifi connections and it will not connect to either. I have followed my university's instructions to connect to the internet but no good. When I run troubleshooter the error says "unable to configure ip address" or something along those lines. I have reinstalled the network adapter, changed firewall setting. I have tried just about anything I can think of.
View 1 Replies View Related I am not a ASA expert but I have configured them few times. I have a vision of a task I have to complete but not sure if it is practical or how to go about doing it.
We two locations, Location A and Location B. Both locations have a 100MB internet conection. Location A has a ASA 5510. Location B has a 5505. Users at both locations access the internet via their respective ASA. Location A is the headquarters and Location B is a disaster recovery site. We want to setup a tunnel between both ASAs. This tunnel will be used to replicate data between the two locations for DR purposes. We need the users to still use the same pipe to get to the internet but want to allocate 10MB for internet use and the remaining 90MB for the DR tunnel.
We are planning to split the Private servers from the DMZ Servers and configure an additional Interface and segment for this purpose.
Private Servers Segment: 192.168.4.0/24 (there is no DHCP all servers' IPs are statically configured)
DMZ Segment: 192.168.3.0/24 (This is a future deployment)
LAN Segment: 172.17.0.0/16
Both, Private Servers and DMZ Servers are in a collocation as well as the ASA5520. There are multiple Branch offices that uses subnets within the 172.17.0.0/16 Network and they are connected to the ASA5520 via Metro-E.
I do not know if this is possible but what I want to do is this:
In order to avoid the change of internal DNS records I want to mask the DMZ servers with a Private Server IP when a Private server or LAN host wants to access it like this:
The FTP server in the DMZ has the IP address: 192.168.3.100. But when a PC from the LAN wants to reach the FTP server it should points to its old IP: 192.168.4.100. This way the PC sends a packet to the ftp.corporate.net (192.168.4.100) the ASA recieves the packet and translate it to the (192.168.3.100) and send it out through the DMZ Interface.
Also if the Private Servers wants to reach the same FTP the ASA will act like a proxy-ARP and send the paquet to the DMZ by means of the translation of the IP.
i'm trying to connect 5 servers together to create a private network.Each server has a network of it's own and i'm trying to make all 5 servers communicate with each other to share and search data simultaneously..
View 16 Replies View RelatedI Have exented vlan 120,121 from DC-1 to DC-2,the DC-1 and DC-2 are connected using L2 Trunk over fiber terminated on Cisco 6513 on both site ,the distance around 40 Km ,on the DC-2 i just assigned server-1 TO VLAN 120 while server-2 in vlan 121 ,but these servers unable to communicate neither with DC-1 Servers or betwen them locally on DC-2 ,pls note that the servers at dc-2 rely on DC-1 for routing.
View 7 Replies View Related