Sweex LW050UKv2 - Obtaining Network Parameters
May 13, 2011
I have had this router for about 5 years now, I had problems setting it up from the start as I was fairly young but I eventually found a way around it - no problems since. Through memory I am sure I had this problem previously but I had the disk to give me guidelines on what to do(which I don't have any more). I have phoned up virgin (my ISP) and they said it was an issue to do with the router, to which I searched into the routers address, in this case 192.168.50.1. Scrolling down, I noticed that under the WAN section it says:
MAC Address:00-16-0A-09-CC-69IP Address:0.0.0.0Dynamic IPSubnet Mask:0.0.0.0 Default Gateway:0.0.0.0 Obtaining Network Parameters...DNS Server:0.0.0.0 , 0.0.0.0
I have spent a good part of today trying soloutions to get this to work again but I just can't seem to find a way around it. As I said, the router has been working fine for pretty much 5 years now and I really do not know why the WAN went. In addition, it was set up wireless. How can I obtain the newtork parameters?
View 4 Replies
ADVERTISEMENT
Jan 13, 2012
My wireless laptop connects fine with my wireless WiFi but, I'm unable to connect to the internet with my Ipad? I don't think it's a problem with my modum. The Ipad asks for my OWNER-PC Network password which I don't have. The one I have written down doesn't work? How do I find or change my password?
View 1 Replies
View Related
Dec 25, 2011
i have sweex lw150 and i want to get connect to another wireless network and share to my wireless laptops.
View 3 Replies
View Related
Jun 23, 2011
A few days ago i bought this router Sweex LW310v2 and when i connect it to the internet,i found that some sites i can open and some sites i can't open. For example, i can open [URL] but i can't open [URL].. My connection to the internet is trough PPPoE and when i am connected directly to the internet i don't have this problem, the problem appears only when i am connected to internet trough the router. Moreover, programs like Yahoo Messenger and Skype can connect to internet trough the router, the problem is only with the sites. These two sites i use are just an example, most of the sites i can't open.
View 1 Replies
View Related
Feb 7, 2011
I've got a ADSL Sweex Modem, connected to a D-Link Wireless Router,The modem is connected to our telephone line, we have other phones connected to other "telejack" too. The router is connected to a computer with wire, and another computer wireless.Every now and then we get random disconnect. Sometimes we can go several months without a single disconnect,whilst sometimes it happens as often as every 3 minute. This is the log:
[code]....
View 14 Replies
View Related
Jun 27, 2011
I want to set a password to secure my internet broadband but the manual states address as 192.168.2.1 - this asks for a username and password which are supposed to be admin and 1234 - although manual shows a screen with just a password and says bypass it.
View 1 Replies
View Related
Jun 29, 2012
I'm trying to obtain the vlans on a trunk and also whether the port is a trunk. Ive seen VTP mib, but these dont appear present on my switch (2950).
View 4 Replies
View Related
Jul 3, 2012
So I received a new modem today and wanted to tandem it with an extra router that I have so I can get wireless at work. Here are the steps I've taken:Verify modem connection works connected directlySet modem to bridge modeReset router, set to PPPOE with proper log in Try to connect, and get the message "Could not obtain IP from PPPoE"I've researched as much as I could stand online, and found these to be the major steps everywhere, most people miss the bridge mode but I'm sure I've done it properly (switched back and forth atleast 5 times). I don't currently have access to the connection but I can respond tonight to questions about what else I may or may not have done, and will take what is suggested here to try tomorrow
View 14 Replies
View Related
Feb 6, 2012
I have had our WLC4400 in place for around five years. No configuration changes have been made to it or the 32 LWAPPs connecting to it. We have begun to have some spotty issues with client devices. The error message says they are unable to obtain an IP address. After they wait a few minutes, they connect. We have plenty of DHCP addresses available. We have 25 locations with at least one AP and the problem seems to be system wide. One person can connect and the person beside them cannot. Many say they have been connecting to our library wireless for a long time with no problems.
View 17 Replies
View Related
Mar 2, 2012
When I'm on a fresh boot on my laptop (full shutdown then starting back up) my wifi connects just fine....perfect.However, when I close the screen (its a laptop) and it goes into standby...when I wake it up again my wifi icon by the clock shows that its still obtaining an IP address or whatever (little yellow dot bouncing back and forth over the icon)....The icon will stay like this until the next time I reset the computer....but the entire time my wifi works as it should....its just the icon thats being weird.
Fresh install of Windows (as of two weeks ago)
Windows XP SP3 - all updates are current
Dell Latitude D610
Dell Wireless 1470 Dual Band WLAN Mini-PCI Card
Broadcom NetXtreme 57xx Gigabit Controller (wired cat5 disabled)
1GB ram
all drivers up to date
Like I said...everything is working as it should..Its done this since I've done the fresh install of Windows, so it has nothing to do with any software I've installed or any of the updates.
View 19 Replies
View Related
Dec 5, 2011
I have a E2500 router and 3 WAP610N access points. Users are having a difficult time connecting to the AP's. The client device just sits there trying to obtain an IP and then times out. If they get within range of the actual wireless router, then connect instantly. Is there a setting to increase that will allow longer time trying to obtain an IP?
I am using the same SSID for roaming, but am using different channels (1, 6, 11) for the overlap. See diagram below. Not sure if this has some impact?
View 4 Replies
View Related
Oct 16, 2011
I have an AT&T Univese which is class G. I want to run it in class N.Do you think plugging my Linksys router into the AT&T will give it to me(class n)?If so, how do I get the linksys parameters set up? It giving wrong readings at its not connecting to the internet.
View 3 Replies
View Related
May 4, 2012
Following the chat with the technical support of CISCO.In few words, the LINKSYS X3000 is the only router in the world that can't shows the DSL line parameters ( SNR and LINE ATTENIATION ) so you can't evaluate the line quality without using another router.... INCREDIBLE!!!!Let's see how long it will be before the firmware update!Me: simple question: is rather embarrassing but I can't find the SNR value (Adsl status) in the Linksys X3000 interface. Same for the Line Attenuation values. These are the standard DSL information and they are essential to evaluate the DSL line quality.Unfortunately, you are right, these parameters are not available on the Gateway (X3000) Setup page.Me:It's unbelievable I use routers for my work and this is the first product that can't shows the DSL line parameters...The only parameters available under DSL Connection Subta are Status, Downstream Rate and Upstream Rate.Me:Do you think it's serious? The price of this product and the target to which it is oriented suggest a more professional approach.I agree, but as of now, this is how it is however, you need to keep an eye on future updates for the device that might include these paraters/features.Me:Please could you send a notification to the DEVELOP TEAM to quickly update this product FIRMWARE and close the gap that separates it from other products in the same category?
View 9 Replies
View Related
Mar 17, 2013
I have configured SSL offloading and redirection on a 4710 appliance. Everything works fine. The issue I am facing is that some parameters in url are getting lost.
I have https://%h/%p configured as a redirect server which works fine as far as hostname and path is concerned. i.e. full hostname and path are preserved, but that there are some parameters after the full path in encrypted format which are getting lost. I think 307 redirect can resolve this issue but ACE does not support that.
View 4 Replies
View Related
Oct 16, 2011
I configure two WIC-1DSU-T1-v2 interfaces with a T1 crossover cable. What are the mimimum configurations to do to communicate from LAN1 (int fa0/0 of one 1841 router) to LAN2 (int fa0/0 of the second 1841 router) ?
Do I need a routage protocole ? And if yes wich one ? Interne or externe (RIP or BGP) Or static route is enough ? Also, is that I should put a encapsulation, like ppp ? Is it neccessary on a point to point line ?
Finally what about the following commands, do I need it ?
service-module t1 clock source internal
service-module t1 timeslots 1-24 speed 64
service-module t1 framing esf
service-module t1 linecode b8zs
View 4 Replies
View Related
Jun 17, 2012
i am adding a wired router,during configuration i must choose between PPPoE,Dynamic,Static connection type. i have broadband cable isp
View 2 Replies
View Related
May 11, 2011
I just bought a DIR 615 (firmware 4.0) which I am using as an access point linked to a Netopia router. The Netopia has QoS enabled and needs to keep it, however I was hoping to use the DIR615 without QoS. I am using a ReadyNas Duo as storage for music, videos etc.Now, here are my issues which I think are all linked.
1) I have a very slow connection wireless, between 1'500 and 2'000kbits/sec download. This was not the case with my very old Linksys router
2) When I try to rip a CD from iTunes to the NAS, it brings up error messages of lost connection and impossibility to rip in the middle of the songs. I did not have that problem with the Linksys router neither.
3) I would like to change the QoS parameters to see how it affects this connection issue, as well as change other Wifi parameters, but they show up as greyed out and I can't change them. (I feel that the DIR 615 might inherit some parameters from the main router, since it is used as an Access Point).
View 4 Replies
View Related
Jan 20, 2013
I have problems with setting the snmp retry / timeout parameters for our devices. I managed to import our devices with bulk import , but after it I realized that for some devices the snmp retry / timeout values were different ( created the bulk file with 3 retries and 30 sec timeout , but in the system the appear with 2 retries and 1 sec timeout). I tried to change it manually , but after a while it goes back to the wrong values.
View 1 Replies
View Related
Aug 9, 2012
I’m looking for some specific parameters of Cisco 1941 and not able to find them .
1. Maximum number of DHCP clients2. Maximum number of DHCP pools3. Maximum number of V LANs on trunk port.
View 2 Replies
View Related
Apr 14, 2012
Just loaded the 7.2.103.0 software onto the brand new WiSM2. Going throught the options and have found that under the global parameters for 802.11a/n, 802.11b/g/n radios is now the "Maximum Allowed Clients" option. The allowed setting is from 1 - 200 clients.
Does that mean only 200 clients will be allowed to associate to the WLC on that radio at a maximum?
Doesn't seems to make sense... I have the 500 AP license on this WiSM2... I know this option used to be an optional setting under a WLAN in previous releases.
View 2 Replies
View Related
Sep 9, 2012
After upgrade to ACS 5.2 appliance , we are trying to configure AAA between Ciscoworks and ACS. Authentication is working but authorization fails , logged user cannot access to admin parameters. I've configured attributes manually but it doesn't work.Does ACS 5.2 support integration with CiscoWorks?
View 1 Replies
View Related
Oct 24, 2012
a customer has bought a new AP 3500 with external antennas and he would like use his old antenna AIR-ANT2485P-R.
We have the option to configure the antenna parameter in WLC under Wireless > Access Points > Radios > 802.11a/n or 802.11b/g/n for external antenna and and using only port A.
But if we enable only one port (Example: port A) we will get a warning message: Need to have at least both dual mode antennas (antennas A and B) enabled
Is it not possible to use an antenna like ANT2485P-N together with an Access Point like 3502E?
View 6 Replies
View Related
Jan 8, 2013
I have a 2500 and I have successfully joined a 1600 AP to it; however I have noticed that I cannot enable CleanAir in the Global Parameters with just the 1602 AP joined. This feature was enable when I had my 2602 AP connected.So, is the problem that the 1602 doesn't fully support CleanAir? If that is the case, how do I enable CleanAir Express or is that something you can even enable thru the GUI?
View 9 Replies
View Related
Jul 9, 2012
I created a LAP Template in NCS to configure some new 1142 LAPs that were installed in a remote office. These LAPs need to be in Flex Connect mode with V LAN support. The template is being applied with partial success on every access point. Details of the partial success say the Flex Connect Parameters fail with the following error.
Provision Failure: { URL}.Object Not Found Exception cannot be cast to [URL]
Am I doing something wrong? The Flex Connect portion of the template has V LAN Support enabled, Native V LAN ID, and the Profile Name- V LAN Mappings configured.
Prime NCS version 1.1.1.24 Access Points are AIR-LAP1142N-A-K9s running 7.2.110.0
View 3 Replies
View Related
Nov 14, 2011
I have a relatively simple question. I would like to create a private network within a larger network, the private network having several clients. I would ideally like the router to appear as the only device on the larger network and all data to be sorted by the router to the clients in the private network.
Will the Netgear FVS318G be able to do that? It seems to have the necessary NAT options.
View 1 Replies
View Related
Apr 4, 2012
I have 4 computers (3 laptops, 1 desktop) in a shared office. We get internet access using their wireless network. All works fine. However, I need to share a printer amongst all of the computers. The printer is LAN enabled and I would normally just put all the PCs on a hub, together with the printer and share it that way. BUT my question is can we access the internet using the wireless network and the printer using a separate wired network at the same time?
View 7 Replies
View Related
Aug 21, 2012
This past weekend I went out of town and took my Windows 7 laptop with me -- since I returned home, it has been unable to connect to my wireless network. Other devices in my home connect to the network just fine, and the problem laptop has always been fine until now. My network card is an Atheros AR9285, and I'm attempting to connect to a Medialink router with WPA password protection and AES encryption.My wireless network icon in the task bar has a yellow sign with an exclamation point in it. It says "No Internet access."
View 1 Replies
View Related
Jan 25, 2011
I use my desktop for streaming media throughout the house. I found it was causing lag for gaming most likely because it was taking up all the bandwidth for the router. We had a 2nd router laying around as well as a 2nd wireless adapter so we set up a 2nd network that was not connected to the internet for strictly media streaming.I attempted to change the network settings so the internet connection appeared as a public network so that streaming of media was hopefully diverted to the non internet wireless adapter.I want a faster way of transferring large video files from my laptop to my desktop. I recently bought a crossover cable to do this through direct connection.Both use the same user name and password as well as run the same win 7 pro however the desktop is the 64 bit version. I set up both ipv4 with the same addresses.When it has worked I am only getting a connection speed of just over 10mb and once I connect the crossover cable between the computers it knocks out my internet connection on the wireless card.
View 5 Replies
View Related
Sep 2, 2012
I seem to be struggling to connect more than 4 cameras to my (ISP-supplied) modem/router by Netgear CGD24N via WPS. I'm on my 5th camera now (already have 3x 930L and 1x 942L) but the newest 942L just won't connect to the network at the moment and there's definitely no faults here as I swapped cameras today at the local retailer (and got an A3 942L!).I've even tried connecting the camera to my wireless extender (Netgear WN3000RP) but no luck there.
So far it has only worked twice for short periods of time (enough for me to configure the cameras) but since then I can't actually get it working. I've got a couple of spare wireless routers lying around too and should be receiving a DIR-600 soon (from the Netgear promotion in Australia) which could be useful?
View 1 Replies
View Related
Mar 26, 2011
I connected my camera to my router with a network cable. It is a DCS-2121, H/W Ver A2, with firmware 1.04_FR.It received an IP address and I could access it fine with a web browser.Then I configured it to work wireless.I disconnected the cable but the camera wasn't accessible.Since I couldn't find it I re-attached it with a network cable, but this didn't work.So I pressed the Reset button to start over again.However, now I cannot get it to work anymore. When I plug in the camera and have it connected with a network cable to the router the status light remains RED.When I plug it in without a network cable the status led remains RED.When I connect it with a network cable to a computer directly, the status led remains RED.I've tried changing the network settings of my router to use 192.168.0.x as range, but it makes no difference. In all cases the status indicator remains RED.
View 2 Replies
View Related
Jan 8, 2013
I'm experimenting/attempting to use a laptop as a network tap between my (DSL) modem and a wrt54gs by creating a bridge with two NICs in the laptop. My problem is I can't seem to get connectivity on the user end of the router. I can't ping the bridge from an end computer...
DHCP is disabled in the router, but even when manually configuring the IP address on an end computer and using the bridge as a default gateway I can't ping out.
Am I completely misunderstanding the purpose of a NIC bridge?
View 1 Replies
View Related
Feb 13, 2011
I want to setup a DC++ HUB for sharing data within the university local network. We have addresses of the form 172.31.*.*. These addressed are accessible within the university bu non routable outside on the internet. My plan is to setup a local HUB for DC++ for sharing data within the university intranet. So even if internet is unavailable data can be exchanged through LAN. This HUB must not be accessable outsied the university network.how should I do this all..implementing network sharing other than DC++. My basic idea is that everybody can share their data and the data is searchable from one common interface( Web interface is better option, if possible). And data featching should prefferably be from many hosts, using multiple connections so that speed can be improved..
View 4 Replies
View Related
Aug 16, 2011
I have a crappy router/modem from comcast with two windows machines and a linux web server connected. I also have another router, a Linksys WRT54G with DDWRT firmware with WAN connected to the modem/router. The linux web server has a static IP, configured with /etc/network/interfaces The network goes down randomly. Disconnecting and rebooting the linux web server usually fixes it. It's possible that the WRT54G could be at fault as well.The problem is that I just don't have any information on what is happening on the network. (Well even if I had the information, I'm not sure I would know what to do with it) I installed wireshark, I figure I should just leave it running until the network goes down, then I can go through the packets and see if I see anything weird?
View 4 Replies
View Related
