Wifi Icon By Clock Shows That Its Still Obtaining Ip Address

Mar 2, 2012

When I'm on a fresh boot on my laptop (full shutdown then starting back up) my wifi connects just fine....perfect.However, when I close the screen (its a laptop) and it goes into standby...when I wake it up again my wifi icon by the clock shows that its still obtaining an IP address or whatever (little yellow dot bouncing back and forth over the icon)....The icon will stay like this until the next time I reset the computer....but the entire time my wifi works as it should....its just the icon thats being weird.

Fresh install of Windows (as of two weeks ago)
Windows XP SP3 - all updates are current
Dell Latitude D610
Dell Wireless 1470 Dual Band WLAN Mini-PCI Card
Broadcom NetXtreme 57xx Gigabit Controller (wired cat5 disabled)
1GB ram
all drivers up to date

Like I said...everything is working as it should..Its done this since I've done the fresh install of Windows, so it has nothing to do with any software I've installed or any of the updates.

View 19 Replies


ADVERTISEMENT

Linksys Access Point :: E2500 Obtaining IP Address Timing Out While Connecting

Dec 5, 2011

I have a E2500 router and 3 WAP610N access points.  Users are having a difficult time connecting to the AP's.  The client device just sits there trying to obtain an IP and then times out.  If they get within range of the actual wireless router, then connect instantly.  Is there a setting to increase that will allow longer time trying to obtain an IP?
 
I am using the same SSID for roaming, but am using different channels (1, 6, 11) for the overlap.  See diagram below.  Not sure if this has some impact?

View 4 Replies View Related

Icon Shows Connected To The Wrong Wireless Network?

Nov 29, 2012

when I hover my mouse over my signal bars it says I am connected to a network named 'home-9C78' but when I click to bring up my list of available networks, it says I am connected to a network named 'Reshiram' Reshiram is the name of my network and there is NO 'home-9C78' ANYWHERE in the list!!! I don't know where my computer gets this home-9C78!!! and I NEVER ever connected to a network with that name!!! it is supposed to be 'Reshiram

View 2 Replies View Related

Network Icon Missing Which Shows The Status Of The Connection?

Feb 5, 2013

network icon missing which shows the status of the connection

View 8 Replies View Related

Wifi Yellow Icon But Connected?

Jul 16, 2012

i connect to the internet using wifi and the 5 bars slowly come up in the lower right and say i am connect but over the top of the bars i get wireless icon with yellow star over it; so whats that all about and how do i fix it nothing should be overlaying the 5 bars ?

View 12 Replies View Related

Dell :: Inspiron 1545 - WiFi Icon In Utility Tray Is Always Showing X

Jan 10, 2012

A few days ago when I updated my dell inspiron 1545, the wifi icon in the utility tray is always showing an x (this means he doesnt find any connections). But when I click on it it says i am connected with my internet and shows different kind of wifi nearby.

View 1 Replies View Related

Protocols / Routing :: Switch Shows Up Router With IP Address

Nov 21, 2012

i got a d-link router comming off modum and then a lynksys switch . well when i run the lorex program it (the switch) shows up as a router with a ip address ? i have tried a different swith but still the same thing happens .

View 3 Replies View Related

Cisco Wireless :: AP 1242 Shows WLC Management IP As Its Own IP Address

Jul 14, 2012

we are using wism 4404 code 4.2 , we are using this old code becuase of 1250 mesh APs, now when a user connect to our network and he is using intel proset software he can see details of our AP, like mac, type and AP ip address 9 which in this case it the controllers ip address) is there a way we can prevent the ap from showing it?...we will be doing an upgrade to 7.0.230 soon. will the upgrade takes care of this problem or there is a way to fix it.

View 5 Replies View Related

Linksys Wireless Adapters :: Wmp600n-eu - Wifi Icon Starts With Blue Circle Spinning

Jun 9, 2011

I recently acquired a WMP600N-EU that is running under W7 x64 with the latest Linksys available drivers for download, which unlike the default MS ones, don't enable the Virtual Wifi adapter.Now with this new adapter, the wireless icon starts with the blue circle spinning, and the at the point the other adapter was already connected, it displays the "orange sun" (not connected, connections available) and stays there dead for some 10 seconds. At this point, my router's SSID is already listed. Only after that time it will start to successfully auto-connect to the pre-configured network, whereas windows has already finished loading or the browser launched unable to check mail.This is obviously not a functional fault on the adapter. If I didn't had the previous adapter to compare, I might find it normal. Btw, I've cleaned every previously stored wireless connections.

View 3 Replies View Related

Linksys Wireless Router :: E3200 Client List Only Shows MAC Address

Feb 15, 2012

I could get a list of clients on the E3200 wireless (or wired) ports. I have my E3200 setup as a WAP LAN-LAN off a switch and it is not the DHCP server on the network. I can see a list of MACs on the client list, but no client names and no IP addresses. They are definitely named and show up on the WRT54GL (DHCP and NAT) as devices

View 5 Replies View Related

Cisco Switching/Routing :: Cat 2960 Shows Mac Address Port As Dropped?

Jul 30, 2012

I am configuring a Cat 2960 port for connecting a VOIP phone, authenticated by MAB.  On connecting the phone, I get the port authenticated and assigned to the correct VLAN, with LLDP-MED advertising the correct voice vlan.  However, I then see no traffic from the phone on the switch.  I can see the MAC address of the phone is learned in the right VLANs, but the mac address is showing as "Drop", which normally means the address is statically configured to be blocked.  There is no static mac address table blocking configured on the switch. 

Switch Version
Switch Ports Model              SW Version            SW Image
------ ----- -----              ----------            ----------
*    1 50    WS-C2960-48TC-L    15.0(1)SE3            C2960-LANBASEK9-M
 Port configuration
interface FastEthernet0/1
description "Standard user port"

[code].....

View 1 Replies View Related

Xirrus Wifi Inspector Shows No Adapters Available

Feb 12, 2011

I am running XP SP3 with .NET Framework 3.5 SP1. The wireless network adapter works fine using either the Atheros Client Utility (my preference) or Windows Zero Config, Since someone mentioned the latter as possibly being necessary, I have been using it for these tests. It is, thus, not surprising that the wireless network adapter is present in and shows no problem in the Device Manager (devmgmt.msc), or ipconfig output; however, Xirrus WiFi Inspector shows "No adapters available" and does not function. How to get WiFi Inspector running?

View 2 Replies View Related

Wifi Connection Shows Authentication Timed Out?

Sep 2, 2012

when i connecting my ipad to wifi network it shows authentification timed out. what is its mean

View 1 Replies View Related

Cisco Firewall :: ASA 5505 Logs All Traffic Shows Up As Router External Address

Nov 10, 2011

I have a cable modem internet connection and my cable modem is connected to an ASA 5505.  The inside interface of the ASA has an IP address of 192.168.2.2 and is connected to a Linksys router's internet port which has an IP address of 192.168.2.1.  The Linksys router then has a local area network of 192.168.1.0 and all my clients are on that network.  Everything is working fine except in my ASA logs all the traffic shows up as the router's external address which is 192.168.2.1.  I would like to see the 192.168.1.x address of the clients in the ASA firewall.  I've tried making some changes to the Linksys router but that hasn't resolved it.  Is there any changes I can make on the ASA to get this to work?  

View 6 Replies View Related

Obtaining Owner-pc Network Password?

Jan 13, 2012

My wireless laptop connects fine with my wireless WiFi but, I'm unable to connect to the internet with my Ipad? I don't think it's a problem with my modum. The Ipad asks for my OWNER-PC Network password which I don't have. The one I have written down doesn't work? How do I find or change my password?

View 1 Replies View Related

Cisco :: Obtaining Vlan On Trunk / Port

Jun 29, 2012

I'm trying to obtain the vlans on a trunk and also whether the port is a trunk. Ive seen VTP mib, but these dont appear present on my switch (2950).

View 4 Replies View Related

E2500 Router Not Obtaining IP From ATT High Speed DSL?

Jul 3, 2012

So I received a new modem today and wanted to tandem it with an extra router that I have so I can get wireless at work. Here are the steps I've taken:Verify modem connection works connected directlySet modem to bridge modeReset router, set to PPPOE with proper log in Try to connect, and get the message "Could not obtain IP from PPPoE"I've researched as much as I could stand online, and found these to be the major steps everywhere, most people miss the bridge mode but I'm sure I've done it properly (switched back and forth atleast 5 times). I don't currently have access to the connection but I can respond tonight to questions about what else I may or may not have done, and will take what is suggested here to try tomorrow

View 14 Replies View Related

Sweex LW050UKv2 - Obtaining Network Parameters

May 13, 2011

I have had this router for about 5 years now, I had problems setting it up from the start as I was fairly young but I eventually found a way around it - no problems since. Through memory I am sure I had this problem previously but I had the disk to give me guidelines on what to do(which I don't have any more). I have phoned up virgin (my ISP) and they said it was an issue to do with the router, to which I searched into the routers address, in this case 192.168.50.1. Scrolling down, I noticed that under the WAN section it says:

MAC Address:00-16-0A-09-CC-69IP Address:0.0.0.0Dynamic IPSubnet Mask:0.0.0.0 Default Gateway:0.0.0.0 Obtaining Network Parameters...DNS Server:0.0.0.0 , 0.0.0.0

I have spent a good part of today trying soloutions to get this to work again but I just can't seem to find a way around it. As I said, the router has been working fine for pretty much 5 years now and I really do not know why the WAN went. In addition, it was set up wireless. How can I obtain the newtork parameters?

View 4 Replies View Related

Cisco Wireless :: WLC4400 Obtaining IP Addresses

Feb 6, 2012

I have had our WLC4400 in place for around five years.  No configuration changes have been made to it or the 32 LWAPPs connecting to it.  We have begun to have some spotty issues with client devices.  The error message says they are unable to obtain an IP address.  After they wait a few minutes, they connect.  We have plenty of DHCP addresses available.  We have 25 locations with at least one AP and the problem seems to be system wide.  One person can connect and the person beside them cannot.  Many say they have been connecting to our library wireless for a long time with no problems. 

View 17 Replies View Related

Laptop Connects To Wifi Network / It Shows No Internet Access Message

Sep 29, 2012

Laptop connects to wifi network. But it shows "No Internet Access" message.My Macbook connects to the internet just fine and the wifi on my iphone works as well.The ethernet on the laptop works and I am able to access the internet this way. The laptop does connect to some of the other access points but I've had issues with my router.I tried the usual debugging mechanisms - disable/enable adapter, reset the router, reset the tcp/ip stack. [code]

View 1 Replies View Related

Tp-link 300mbps Wireless :: Tl-wr1043nd / Wifi Shows Good Signal But No Internet?

Apr 18, 2013

Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version :
ISP : HughesNet

I received this router today, I have a MacBook Pro and a iPhone. The router came with a very small cd, I was very disappointed because , when I purchased this router from amazon , the discription read that this router is Mac compatiable. But that is not true if the cd is not compatiable! My problem is I get a good signal for wifi, but I can not open any websites with my Mac or my iphone.

View 1 Replies View Related

Cisco Firewall :: ASA 5520 - Memory Shows 94% And CPU Shows 85%

Oct 15, 2012

I Have asa 5520 with the  code 8.0, the mem shows 94% and the CPU shows 85%

View 5 Replies View Related

What Is Maximum Clock Frequency Of LAN Card

Oct 12, 2012

what is maximum clock frequency of LAN card?

View 3 Replies View Related

System Clock Does Not Match Local Time?

Jan 16, 2011

I'm trying to get an HP laptop running Win7 to see a desktop running WinXP on my network (both wired and wireless) When I run the troubleshooter in Win7, it tells me "system clock does not match local time" as the reason. I have a Belkin wireless router attached to my cable router. I have updated the system clock via the internet on the desktop and checked the time setting in BIOS. These seem to match. I have googled around on this and can't find any accounts similar. My son's Vista laptop and the Win7 laptop have seen each other since day one. The laptop and desktop did see each other at one time, but the connection was lost after I went to a hotel and changed public network settings temporarily. I can ping the desktop from the laptop, but it times out when pinging the laptop from the desktop. I'm running an avast firewall on both, but can't see a problem there.

View 6 Replies View Related

Cisco WAN :: Max Clock Rate - WIC 2T For 2851 And 3845

Jun 11, 2013

I am trying to find information on what the max clock rate supported on WIC-2T on a Cisco 2851 and Cisco 3845 Routers.

View 1 Replies View Related

Cisco Infrastructure :: 2960 Clock Time Not Set

Mar 6, 2012

I am using Cisco 2960 access switches and dont have NTP server so i can manually set time on switches but problem raised when these switches restart they show their factory default time.

View 2 Replies View Related

Cisco WAN :: 1841 Clock Time Is Not Stable?

Mar 8, 2012

In cisco 1841 clock time is not stable.Every time the clock time is changed.

View 4 Replies View Related

Cisco :: Show The Clock Rate Received On The DTE Side?

Jan 1, 2013

what command will show the clock rate as received on the DTE side of a back-to-back configuration?the show controllers command shows the configured clock rate on the DCE side.But how about viewing the received clock rate on the DTE side?

View 4 Replies View Related

Cisco WAN :: Clock Slips On VWIC-2MFT In 2811

Apr 11, 2005

I have a 2811 that I'm in the process of turning-up to support a 4xT1 using VWIC-2MFT-T1's.  The question is how to "correctly" set clocking on the MFT's.
 
As is typical of the 2MFT's, as soon as a 2nd T-1 on a VWIC-2MFT comes up, I start taking "Slip Sec"s on the 2nd T-1.  I have tried different clock source combinations, including "clock source line primary", various "network-clock-participate" (or not) combinations, and about a dozen other stab-in-the-dark configurations.  Before I started playing with it, the slips were consistently every 9 seconds.  After playing with it, I got them to every 18 seconds.  But there shouldn't be ANY.  So the question is what SHOULD the correct timing configuration be on that platform? 
 
The VWIC-2MFT-T1's are in slots 1 and 3, so the controllers involved are 0/1/0, 0/1/1, 0/3/0 and 0/3/1.

View 9 Replies View Related

Cisco Switching/Routing :: Clock For SIP Phone 3905

Jan 23, 2013

What happens with the sip phone 3905, because i cant set the rigth clock. its always display plus 2 hours from the right time in Brazil.

View 3 Replies View Related

Cisco WAN :: 4948 / NTP Master - How To Make Clock Set Become Permanent

Oct 29, 2012

I understand that most of the cisco switches does not have a battery-supported system clock. The better solution is to setup the NTP server and let the rest of the switches to synchnorise the clock with it. How about cisco switch 4948? Does it have a battery-supported system clock?If the cisco switch 4948 is the NTP master, how I am going to make sure that the clock will not be reset after reload?

View 3 Replies View Related

Cisco AAA/Identity/Nac :: 6500 - ACS 5.2 - Clock Skew Error

Aug 14, 2012

I have  6500 VSS Core Switch configured as NTP Server .I have installed ACS 5.2 vmware and sucessfuly integrated with the AD . I have noticed in some case, i lose connectivity between ACS and AD and when i say test connection , it shows clock skew error . Reboot of ACS sometimes solves the issue, else it comes up automatically after some hours . In core switch , i have configured time as PST +4 and in ACS it is configured as PST +4 , which automatically goes to GST.

View 15 Replies View Related

Cisco Switches :: SGE2000Ps / Unable To Communicate With Time Clock Across VLANs

Jul 3, 2012

I have a situation where i am installing SGE2000Ps to replace my old switches and configuring VLANS. The time clock will not communicate across the VLANS. If I unplug the network cable and plug it back in I will get two successful pings. If i use a PC configured with the same network settings as the time clock and plug it into the port for the time clock it communicates fine.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved