When Service Came Back To Normal One Of Network Connections Was No Longer Available

Feb 14, 2012

I was having an issue with Comcast phone and internet services.Comcast had me disconnect and reconnect my modem and router. When service came back to normal one of my network connections was no longer available to me. I have two connections (one for use at my home which is a secured one) and one I use when I go to my sons home. My computer now only allows me to connect to a network called "Linksys" which may be available to the public. The connection I want to use shows up if I go to control Panel/View Network Status/Manage wireless network, and it is the first choice on the list, but the computer always uses the unsecured "Linksys". I'm afraid to do my banking over that network but I'm also afraid to start fooling with it and having no network. [code]

View 14 Replies


ADVERTISEMENT

Cisco WAN :: 1841 Securing E1 Back-to-back Connections

Aug 28, 2012

securing a back-toback connection using E1.The connection is between two cities, using 2x CISCO 1841 router + VWIC-1MFT-E1 interface at each city.
 
The E1 connections has been provided by our local telco, and they are completely private. The customer is a bank, and they asking me if this is a secure connection or not. If possible, we need to guarantee that no body can get access to the bank network even if they brought E1 modem at one of the ends (telco PoP).

View 11 Replies View Related

D-LINK DSL 2730B - Reset Router To Get Internet Speed Back To Normal?

Jun 12, 2013

I have a router that needs to be reset to get the internet speed back to a usable speed. It is a fairly old router (D-LINK DSL 2730B) and it does get quite annoying. There is allot of devices connected, which may affect the speed, but I am sure it shouldn't change upon reboot. I literally reboot every hour or 2 during peek periods.

View 1 Replies View Related

Linksys Wireless Router :: Bridge Mode E2500 - Reset It Back To Normal

Nov 18, 2012

I accidently went into bridge mode on my linksys E2500 router. I want to reset it back to normal but i'm not sure how to do it. i tried the little reset button on the router but that didn't change it.

View 4 Replies View Related

Network TCP Connections Attempted By Service Files - Security Risk?

Mar 10, 2012

My AV often reports my windows 7 ultimate 64 service files, such as winmon.exe or or service.exe requesting opened TCP connections along with a number of .DLL filkes, and then times they are flagged as heuristic behavior modification, however i know many of those are undeletable, due to windows security replacing them as soon as they are noticed to be missing and in another thread it was also indicated that these must be deleted from three places at once almost to actually prevent those from being instantly replaced, this explains maybe why i get this repeatedly immediately after boot up, but after five or some times it slows down to now and then.still quite a hassle to stop on start up.

View 2 Replies View Related

Cisco Wireless :: AIR-WLC2006K9 Service Contract Can No Longer Be Acquired For Device

Oct 23, 2012

I have a Cisco AIR-WLC2006-K9 in my Cisco lab where I work on my Cisco skills, I recently had the need to update the software on my WLAN controller but his is according to the website only available with a service contract. On trying to get a service contract I found that the device is EOL and EOS and ths no serrvice contract can be purchased for this device and hence no ability to download software for it. So here is my question, when a device is EOL and OES and service contract can no longer be acquired for a device why does Cisco not either open these up for download AS-IS or provide some kind of agreement for people like myself who have moslty EOL and EOS equipment in their labs where we can acquire the needed software to keep our skills sharp in an affordable way ?

View 0 Replies View Related

Wireless Connections No Longer Working?

Apr 23, 2011

My Internet surveillance stopped working

View 1 Replies View Related

Broadband :: 2 Internet Connections One As Back Up?

Mar 24, 2011

I have a primary internet connection which is broadband and the secondary connection as a Reliance data card in my laptop. I have noticed that which ever connection,connects the last, becomes the primary connection and if the primary ever goes out, the second connection takes over and gives me continuous connectivity.Is it possible to configure and specify which connection I want to be primary regardless of which connection connects last etc?

View 1 Replies View Related

Linksys Wireless Router :: E4200 Wired Connections No Longer Work

Jul 14, 2011

I'm trying to fix the network at a student housing building and the system is kind of a mess.  We bought a new E4200 to replace our old Linksys router which no one knows the admin pw to.  We have four switches for 50 connections throughout the four story house and when switching the connections over to the new E4200 all of the wired connections no longer work.  Switch back to the old router and presto.  How do I need to change the settings with the E4200 to get it to work?
 
Also, as it's a thick old house the E4200's wireless only covers maybe half of it...I purchased two wireless repeaters to put on the 3rd and 4th floors, are these simple to install with the router?

View 4 Replies View Related

Linksys Wired Router :: E4200 No Longer Accepts Wired Connections?

Oct 11, 2012

My E4200 router no longer accepts any WIRED connections. I can connect from the modem to the computer and everything works as expected. I can connect other computers wirelessly to the router. I cannot connect any laptops WIRED to the router. Nothing has changed on the systems to restrict internet access. There is something wrong with the router and the WIRED ports. I tried going through the troubleshooting on this site but it was of little to no assistance. The Cisco Connect utility doesn't appear to accomplish anything either. My guess is because I cannot connect to the WIRED ports on the router to connect to the internet to allow for whatever troubleshooting that needs to be done.

View 2 Replies View Related

Network Is Slow With Normal Switch Connection?

Feb 18, 2011

My network is slow with a normal switch connection. How do i improve the connection and can cisco switch improve performance?

View 6 Replies View Related

Home Network :: Using Wwan As 3rd Normal Wifi Antenna?

Feb 26, 2011

I'm planning to replace my flaky minipcie wifi and I need advice about the antenna.My laptop has two sets of antenna, one for 3G WWAN and the other is for normal wifiAccording to the labels, both is "Main" and "Aux". The card that I'm planning to get is an Intel 5300 which has 3 antennas.Since the normal wifi only has two antennas, can I use the 3G WWAN as a third antenna? If yes, should I plug in the "Main" or the "Aux"? If no, Should I buy those additonal antennas in Ebay for the 3rd one?

View 2 Replies View Related

Network Adapter Not Found On Device Manager In Normal Mode?

May 24, 2011

Network Adapter not found on Device manager in normal mode, when in safe mode it shows the Network Adapters

View 1 Replies View Related

Cisco Switching/Routing :: ATM 8510 Back To Back With 7206vxr 155Meg Only Get 44Meg?

Nov 25, 2012

I have a Cisco 8510msr that is connected back to back with a 7206vxr across a 155Meg connection.I receive lots of Output drops on the 7206vxr interface facing the atm switch. When I do the following command:-

kwdair9#sh atm int atm 1/0Interface ATM1/0:AAL enabled:  AAL5 , Maximum VCs: 4096, Current VCCs: 27 Maximum Transmit Channels: 0Max. Datagram Size: 4528PLIM Type: SONET - 155000Kbps, TX clocking: LINECell-payload scrambling: ONsts-stream scrambling: ON797522 input, 881483 output, 203946630 IN fast, 223768062 OUT fast, 0 out dropVBR-NRT : 110288 Avail bw = 44712   <====  

I only have 44megConfig. is ACTIVEkwdair9# I only get 44Meg of the available 155Meg.There is no QOS on the router and the only commands I can find that vaguely see that refer to QOS are on the ATM switch:-

atm address 47.0091.8100.0000.0007.0d87.b201.0007.0d87.b201.00atm router pnnino aesa embedded-number left-justifiednode 1 level 56 lowest  redistribute atm-static?why this is acting like a DS3 link and not a 155Meg link?

View 4 Replies View Related

Cisco Switching/Routing :: Connecting Two 2951 Back To Back Through A HWIC-4T1 Card

Dec 4, 2011

What cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?

View 1 Replies View Related

Cisco Switching/Routing :: HWIC-4SHDSL-E Router Back To Back Connection?

Apr 11, 2013

I have two site that has a copper wire ( 2 wire) connection between each router ( No Telco in between ). Now I want to use 1921 router with HWIC-4SHDSL-E card to connect these two site together. Can I use attach configuration to make the connection reference from the diagram ?

View 1 Replies View Related

Cisco Switching/Routing :: Connecting 2650XM - 2620 Router Back To Back WIC - T1?

Nov 25, 2011

I have 2650XM  router and 2620 Router Both routers have built in WIC  T1 CSU/DSU cards
 
2620Router --
 
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
  Hardware is PQUICC with Fractional T1 CSU/DSU
  Description: DTE  side
  MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation HDLC, loopback not set

[code]....
 
My question is that cisco website says there are two type of cable connections for this type of config --which are  --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable  it did not work.So for this type of connection i know i need T1 cross over cable--  which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over  --  will this cable work in my router to router connection.

View 5 Replies View Related

Cisco Switching/Routing :: 2611 / 2801 - Configuration For Back To Back Support

Oct 19, 2012

I have 1 2611xm router and 1 2801 router. For my own lab purpose, i want to configure them back to back to support voice services. I don't know what configuration will be required at each end. in 2611xm, i have NM-2V and its also detecting the card, so i hope it will work ? also what commands i need to run on both ends .

View 1 Replies View Related

Cisco WAN :: 1921 / Connect Two Router Back To Back Via 2 Pin Copper Wire?

Jan 8, 2013

I would like configure two router (e.g. 1921) back to back via a 2 pin copper wire.  Can I use HWIC-4SHDSL-E card to do it? What is the configuration I can use?

View 7 Replies View Related

Cisco WAN :: HWIC-4SHDSL-E Router Back To Back Connection

Apr 14, 2013

I have two site that has a copper wire (2 wire) connection between each router ( No Telco in between )Now I want to use 1921 router with HWIC-4SH DSL-E card to connect these two ste together.Can I use attach configuration to make the connection reference from the diagram?

View 2 Replies View Related

Cisco WAN :: E1 Clocking Back To Back 3925 Routers

Feb 29, 2012

Just to get this clear as having issues with a E1 link with CRC's at one.Router A,Network-Clock-Participate WIC 1,Should router B have clock participate for WIC 1? We currently have controllers set as UNFRAMED but guess we can set to NO-CRC4 both ends and telco will pass this.

View 1 Replies View Related

Cisco Routers :: Connecting Two RV082 Back To Back

Jan 7, 2013

I'm looking for instructions on how to setup and connect two RV082 routers together with a crossover cable between their WAN ports. This is to connect two separate LANS together via an ethernet connection. For staging we are setting everything up with a crossover cable in our shop.  Ultimately the crossover cable will be replaced by a microwave link between the two LANS several miles apart.  There will be no internet connection.

View 7 Replies View Related

Cisco WAN :: Connecting Two 878 G.SHDSL Routers Back To Back

Apr 7, 2013

I searched a lot but couldnt find a clear document about connecting 2 G.SHDSL routers back to back.First of all I am not sure which type of cable (RJ11) is used for connecting two 878 routers. Does it have to be cross or straight cable.
 
Which RJ11 pairs will be connected each other [code]
 
According the configuration samples One router must be CPE and the other must be CO for simulating DSLAM.

View 2 Replies View Related

Home Network :: Desktop No Longer Listed Under Network Of Laptop?

Oct 30, 2012

I have a Dell Optiplex running XP wired to a Netgear router. My laptop is a Dell Inspiron 1501 running Windows 7. When I got the new router everything programed easily and I could retrieve files from my desktop and print remotely. Sometimes I would have to "refresh" before the laptop would detect the desktop but now it will not detect the desktop or the printer. I suspect that a Microsoft Update did this but just guessing. I went back and deleted the updates that downloaded around the time that this stopped working. I have tried every thing that I can think of to get it back working but can not get it fixed.

View 2 Replies View Related

LaCie 5big Network 2 Drive No Longer Shows Up On Network?

Aug 11, 2012

I'm trying to see if I can fix my friend's NAS which apparently has some pretty important data on it that wasn't saved anywhere else. They actually had the Geeksquad look at it and they've come to the same conclusion I have so far, but I figured I would ask the internet before I gave the thing back to them and said Geeksquad was right.

Anyways, they have this 5 drive RAIDed NAS which apparently just stopped showing up on their network. I borrowed it from them to see if I could figure it out. It turns on just fine and my router assigns it an IP address, but the IP address just takes me to a blank LaCie dashboard screen. It's weird because it's clearly running it's web server because it's just a gray background with an empty white box and "(c) LaCie 2010" at the bottom. No content at all.

Additionally, I tried installing the LaCie Network Assistant on my home computer and it says it cannot find any network disks. I've tried the "wake up a device" where I enter the mac address, but that doesn't do anything.

All the lights are solid blue on the front and over all the drives so it doesn't appear a drive has failed or something. Even so, that wouldn't really explain the blank dashboard right?

View 1 Replies View Related

Cisco WAN :: 888 SHDSL Routers Back To Back

Dec 15, 2011

I'm having some trouble getting two Cisco 888's to work correctly back to back.. The two routers will ultimately be used in conjunction with a BT EPS8 circuit which is effectively four wires short distance between customer sites. We have configured lots of these using the older Cisco 878's.
 
Anyway, as i've been struggling to get line sync on site I've gone back to basics and connected the two 888's back to back. However, I've found that no matter what I do I can only get the routers to sync at 384kbps!? And that's with a one meter RJ11-RJ11 cable.. Very strange. When we've used the 878's we get much more bandwidth. I have tried statically assigning the line rate at both ends but it still only works at 384kbps.

View 3 Replies View Related

Can No Longer See Network

Mar 12, 2012

I have been using my wireless (linksys) for years now and just recently my wifi network no longer shows up on any of my devices (laptop, phone, etc). I am able to hard wire into the linksys and my laptop works but when I try to connect wirelessly, I can't even see the wireless network, I am only able to see my neighbors.

View 2 Replies View Related

How To Get Back On Old Network

May 11, 2011

I have a desk top not wireless i have a laptop wirelesss i have a linksy wireless router i jumped or seomething happen to my desk top i have no promlems getting on line. My desk top used to be on network abc and now it says it is hooked up to network 2 and all these messages keep coming up with my firewall i tried to get back on abc network and can't i have to play around to get on network 2 to get on line.

View 6 Replies View Related

Sharing :: The Specified Network Name Is No Longer Available

Oct 24, 2011

I work next to someone who has been complaining constantly about how his computer will give him some kind of "Access is Denied" error on one of his network drives almost every time he uses it. Other network drives on the same server work. Because it can be fixed by rebooting, the IT person has filed it as low priority / given up on fixing it but I would really like to shut him up but I can't find the answer in google. His computer is Windows 2000 SP4 and the server is Windows NT 4.0.

Edit: It happened again and I was able to get the actual error message. "H:DIST is not accessible The specified network name is no longer available"

View 7 Replies View Related

Vista Showing Normal Wireless SSID Plus Showing Second Unidentified Network

Feb 5, 2011

my computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.

View 13 Replies View Related

Sharing :: Specified Network File Name Is No Longer Available

Jul 20, 2011

How to solve this error in between windows 7(Host) & Windows server 2003(Guest).

View 2 Replies View Related

Network Computer Does Not Reply Back

Jan 10, 2013

I have a problem in my Computers network. We have more than hundered computers in our network. When I ping from my computer to other computers that are on the same switch. Does not show any problem. But when I ping to the computers that are on the switched which are not directly connected to the same switch but are on the other swtiches. Ping replys some times and some times it gives request timeoue.

View 1 Replies View Related

SF310 - Can't Back Up It To A Network Drive

Feb 16, 2011

I want to back up my samsung 310 to a network drive and seem unable to do so using Samsung backup and with windows 7 home you cannot back up to a network drive. It is a home network.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved