I have to used the comsats Internet modem and connect to three Access Point for using the wireless internet but when using the wireless internet then they occur the problem and breake the connection for few minute.
View 1 Repliessome of the websities like facebook are blocked
View 2 Replies View Relatedhow do i connect to internet>? I have a wifi modem connected. With a browser?
View 1 Replies View RelatedJust purchased a Belkin N600 DB N+ Wireless Router because the wireless on my Actiontec PK5000 really isn't so great. When I hook up the router to my modem and after running the install CD I couldn't get connected to the internet. So I looked at my modem and noticed the light where I had plugged in my router VIA ethernet wasn't lit up like the rest of my ethernet ports even after switching them around.
View 6 Replies View RelatedI have a Dell Studio 17 with a wireless internet problem. The wireless internet just stopped working with a message error "modem has been removed". When I try to plug in to a hard wire connection I can connect, but the 3G network want allow me to go on online without the above error messageand a message asking me to select the service you want to connect too, yet it still tells me that I am connected.
View 1 Replies View RelatedImmediately after a power outage, my internet connection predictably drops after a set period of time or usage. It is either after about 30 min or 5-15 mins of watching Netflix. I have a modem hooked up to a wireless router and use the network on my iPhone, laptop and Roku. Since the problem, I have dropped to just having my laptop connected but this has not worked. The wireless network will disappear after the 5 - 20 mins, the light on the modem and router will show no internet (all other lights are normal). Internet connection will be reestablished if I either unplug both the modem and the router (not just one or the other) OR if I unplug the ethernet line from the modem to the router and plug it directly into my laptop (the internet light on the modem will go from "off" to "on"). Despite internet connection working from transferring from the router to the laptop if I connect it back to the router, the internet lights goes off again (resolves upon unplugging and plugging modem and router back in). The internet has not yet dropped when it is physically plugged into my laptop.
I have tried the following:
-Powercycling (temp fix until it crashes again)
-Plugging into a different outlet (I cannot connect it to a different phone line, only have 1 with DSL. Also, I do not have phone service or cable, just internet via DSL)
-Resetting modem
-Resetting 2 different routers
-Calling ISP, their test of the modem was inconclusive
Again, my wifi does not see my network whenever the internet is dropped or the ethernet cord is unplugged from the modem. The outlets I have it plugged into has some type of electrical issue, two electrical devices have shorted out in the room they are in. I do not think this issue is electrical, everything seems to have constant power (unless the power outage shorted out something in the modem). Below are some details of my modem and router. I will provide any additional info requested. I will gladly buy a new modem but I want to see if it can be fixed first.
My modem: Westell
WireSpeed Dual Connect
Model: A90-210030-04
DSL Statistics
Line State: Up
Modulation: G.DMT-Mode
Data Path: Interleaved
[code].....
Router: Linksys E2000 Internet Connection Type: Automatic Config - DHCP (I tried PPPoE and it never got a valid IP address from my ISP)
I am trying to come up with a standard way to configure controllers for my field guys. I'd like to just have them paste in a config that has all the settings, like we use to be able to do on aIOS. I am not seeing away to break out of the wizard so that they can just paste in a config. Do you have to go through the wizard in order to get to a CLI ?
View 8 Replies View RelatedFrom last two days, my internet disconnecting frequently. Modem catching correct ip but no internet connection.modem catches correct ip address n other things, it shows connected to home network (i.e hathway) and internet access is allowed but browser display error 'webpage is not available' (same result for login page of ISP). I have tried different browsers but same result. windows network diagnosis center results as "your computer appears to be correctly configured, but the device or resource is not responding " OR "login.hathway.com is online but still not responding after couple of tries"(second error is not correct word to word tht was the over all meaning of it)In ping test, ping to default gateway gives very good result as 5-20ms but 'request time out' for url...So am not understanding whether it is my pc's problem or from ISP.I m using single pc with wired modem. windows 7 no changes made in network n sharing center.
View 2 Replies View RelatedI have 2 pc's this one is obviously hooked up to the net, the other one works fine, but when i try and plug it into the modem it tells me no internet connection even when i unplug this one and plug the other in.
View 1 Replies View RelatedMy main Internet connection is a frontier modem /router It is on the main level of the house. In the basement I am trying to set up the cisco E3000 through an Ethernet cable.
View 4 Replies View RelatedIs it possible to run both LAN connection and dial-up modem for internet on the same system?
View 11 Replies View RelatedI have a CDMA compatible modem which connects to my Desktop PC via USB.it works fine, but I'd like to share my internet connection with another Laptop, Wirelessly via a Router. The router connects to my Pc via Lan cable. I activated Internet Connection Sharing in the properties of my modem and connected it to the Internet.I hoped my Router would detect an Internet connection on My network and would enable internet connectivity on My wireless AP on the Router. But it didnt. is that windows refelcts "internet access" on both the actual Wireless network on my Router ("49 network") , and on both the Physical Connection to my pc via the Ethernet port ("3G Router") my laptop connects to the router, but without access to the internet, and I keep getting an 'unable to resolve host' message in my Browser. Suspecting my Router of somehow causing the problem I also tried setting up an Ad hoc network instead (using my wlan card to interface with the Laptop directly). They connect fine, and my Printers and other shared resources all appear, but the wireless range between them is like bluetooth compared to the great range of my router.& I still cant manage to share an Internet connection between the two machines!
View 9 Replies View RelatedWhile I was out of the house, my father rearranged the network cables a bit. I don't know what he has done exactly - He says nothing more then pulling and untangling.
When I came back home, my internet connection changed its IP from 192.168.0.205 to 169.254.197.233. The speed changed from 1Gbps to 10Mbps. It has also been at 100Mbps for a while. My subnetmask changed from 255.255.255.0 to 255.255.0.0. The standard gateway changed from 192.168.0.1 to no standard gateway. My DNS servers remain the same.
I have checked the lights of the UTP ports, and it looks like it's only sending a heartbeat every few seconds.
All the cabling is gigabit, my network card is a Realtek RTL8168C(P)/8111(P) Family PCI-E Gigabit Ethernet NIC (NDIS 6.20). THe modem is a CBN SVG6540E.
I have a big 2 floor house .I would like to use 3G connection using USB type of modems,like vodaphone or MTS. which router to be used so that I can get good connectivity on both floors. NOTE- I do not want to use cabled internet coonections.
View 2 Replies View RelatedIs there a way for me to connect my desktop PC to my laptop, & use the laptops EDGE/GPRS modem in the PCMIA slot of the laptop to access the Internet? I also have a wireless router that is not being used for anything, however, I use the laptop to get online, & I'd like to share that connection with my desktop at home.
View 1 Replies View RelatedI recently needed a new router from my internet provider. They came to my home and set up Westell 7500 modem router. My home computer brings up internet with no problems or delays. Unfortunately, my wireless laptop won't recognize any network.I plugged it in using the ethernet cord directly to laptop and modem and still no internet. I'm frustrated, I use my laptop all the time and without the internet it's worthless.
View 1 Replies View RelatedI have a broadband connection through a TV cable connection to a ISP provided modem/wireless box. I have a wireless network set up already from this box. I wanted to extend the wireless network to a hard to reach area so i bought a seperate router (d-Link DIR-615 revE3).
I connected one of the 4 LAN outputs from the modem to the router's "Internet" input. Windows 7 detected the new router's wireless network and guided me through setting up a name and password for it. However there is actualy no internet access on this network even though it's directly connected to the modem.I was thinking that i wanted to just extend the original wireless network but a new network is fine if only it would use the internet from its LAN connection... a desktop computer has connected from the same LAN output of the modem without any security and been able to access the internet from it.
When installing the DIR-615, router installs, but error msg that there is no internet connection. SmartConnect is plugged into the WAN and I have tried the ethernet cable to the computer in spots 1 & 2. Good connection when SmartConnect modem is connected to computer directly.615's Internet indicator will turn green for a while, usually less than a minute or two, then flashes, then may actually cause the routers status indicator to flash off, then back on. Like a reset.
View 2 Replies View RelatedTrying to figure out if I have a bad modem or bad wiring leading to the modem.I'm losing connectivity usually in the evening when I'm sure everything is more loaded.he reason I'm concerned about the modem is that when I lose connectivity, I can't access the modem through my browser. It won't respond. This isn't just for a moment. I'll unplug the modem and plug it back in. I can access the modem after that with my browser, but more often than not, I don't regain connectivity. It keeps trying and failiing.its a Motorola SB5100 from 10 years ago. how to seperate bad wiring from a bad modem?
View 4 Replies View RelatedCable modem connected directly to a Dell Vostro laptop works fine. Same cable reconnected to Dell Dimension 4700 is not working. This has all been working fine for years - usually I have a wireless network with the 4700 connected to the router by Ethernet cable, and the Vostro connected by wireless, but I have removed the router to close in on the problem.First, I am not sure if my ip settings are correct. This is the output from 'ipconfig /all' [CODE].
View 5 Replies View RelatedI have 3 systems in my office, LAN connected. how to setup internet connection for every system with BSNL broadband DHCP modem.
View 2 Replies View RelatedWhen I start up my computer I cannot get an Internet connection. To get a connection I have to go into Control Panel, open Device Manager, click on Network adapters, which opens Realtek PCIe GBE Family Controller. I uninstall the Controller, restart and I then get an Internet connection. The Realtek controller then re-installs itself. I am using Windows 7 Home Premium operating system on my desktop. I am wired through a Dynalink RTA 1320 Rev 2 ADSL2+ Modem Router (provided and checked by my ISP). I have a Netgear Wireless N Router WNR 2000 for wireless connection to my laptop which has a Vista operating system. I have no connectivity problems to the laptop. I have had the connections checked by my ISP and the Netgear router by Netgear. They have both confirmed that there is connectivity to the desk top and the laptop and that the connections are working. Both have said that there is an issue with the operating system. I have got all the latest drivers installed and I get the message "Best driver software for your device is already installed".
View 10 Replies View RelatedThe detected problem is the connection between my access point, router, or cable modem and the Internet is broken.The network gateway is accessible, but Windows couldn't receive network traffic from the Internet.All other devices (iPad, Xbox, android phone) have no problem connecting to the Internet.Desktop is the only one experiencing the connection issue.
View 1 Replies View RelatedMy laptop died last week and have been using my husbands, which I hate! We had some issues with computer freezing on some webpages or after being on webpages for awhile (like facebook). Yesterday it froze and I could not get it back on. When he got home he did scan disk (which I also did) and got it working after going into safe mode and doing system restore. He said an update had gotten through and messed things up. Anyhow, after he was on it a few hours last night, we lost connection. I figured the crazy weather was the culprit but it has been off all day. Our router is working and connecting but the adapter is not. Also our home phone says there is no line. We have unplugged everything several times, checked to make sure everything is in the right spots, I have even reset the router and rebooted the adapter. I uninstalled and restalled the adapter also. It is now telling me that "the connection between your access point, router, or cable modem and the Internet is broken". The only lights I have on the adapter are power, battery, DS and now the US light is blinking. The online and link lights are not on.
View 3 Replies View RelatedMy internet connection drops every 10-30 minutes and reconnects. The modem seems to reset (every light except the power one). I have a Zoom model 5241 modem. Additionally, I cannot access my modem's status page [URL]. It's as if I'm trying to access a site that doesn't exist. Comcast sent a tech who replaced a splitter, but that didn't work.
View 1 Replies View RelatedI'm trying to learn Cisco ASA IOS commands, I have bought myself a 5505 ASA for my home network and plan to implement it. How best to configure it.
I have attached a diagram of how I want my network to look. The internet connection is via the Virgin Media cable modem.
I got a retired Zyxel Zywall USG200 from work. Its working just subs ran out. Was thinking of putting it on my home network, any reason not to? I'm a sys admin, not network engineer, so while I'm capable I'm not an ace with this type of equipment.. Which is why I want to mess with it. I'm currently RTFM and it seems pretty straight forward. If it seems like a viable piece of equipment I'd like to use it full time.
How bad can I break the internets and subject myself to the wrath of my wife's downed internet connection =D if I plug it in between modem and the switch?
we using Linksys router for Internet for different vlans now we take 3750 as core switch for another different vlans 10,20 we create v Lans 20,20 also create cpd servers and we need Internet for vlans 10,20 through linksys router how should we configure?
View 5 Replies View RelatedEarlier today I attempted to change the setting on my Westell 6100 modem such that it would simply bridge the connection to my Linksys WRT54GS router, basically involving setting the router to bridge only and turning DHCP off. Now I no longer get an internet connection through my router when previously the connection had worked perfectly fine before. I following the steps of cloning the MAC address to the router and have done the proper resetting steps (computer, them router, then modem) but I simply can't get an internet connection through my router. The process to set up simple bridging from the modem what supposed to end up with the internet light no longer turning on but the light turned back on following one of the resets.
Currently, I can connect to the internet through the modem just fine but I get nothing when I include the router. I'm not sure if there are some other settings I'm supposed to be changing as I can't seem to find anything past what I've already done when researching online. At this point I would just be happy reverting the settings I've changed but I don't know how to access the modem now that DHCP is off.Basically, I'd prefer to be able to get the router working with these new settings but if that proves too difficult (as I've heard it can be when trying to get Westell modems to work with Linksys routers) I'd like to learn how to access the modem and change the settings back to what they were (preferably in as simple terms as possible as I don't particularly understand what a lot of these settings/configurations do).(And a bit of an aside, but I had attempted to do this modem bridging to "fix" perceived internet speed problems. I've been averaging around 300Kbps download rates ever since I've had this internet connection from Verizon when the supposed download rates should be between 1MB and 1.3MB. Doing this modem bridging had been reported to fix some modem/router conflicts and improved connection speeds for some.)
My facebook site is blocked by firewall . how can i open it ?
View 1 Replies View Relatedbreak the password of DELL PRECISION 390.
View 7 Replies View Relatedi have cisco 1941 router.unfortunately i dont remember password.Can any body tell me how to break password.I tried to go in Rom mon using ctr+break but nothing is happened.
View 5 Replies View RelatedI have a 3845-Mb that has a username and password already on it. This needs to be wiped as its a sold unit. However i cannot break into teh IOS in Hyperterminal using Ctrl-Break either as it boots or after teh IOS image has loaded (after it shows Decompressed image {ok} etc). I have tried several break key combinations such as ctrl+F6+break and they dont work either. On boot the unit does show Password recovery Functionality is disabled. IOS image is 12.4(13r)T.
View 6 Replies View Related