Wireless Router No Longer Recognized?
Dec 8, 2011
I have never had to do anything to connect to my fathers netgear router or my own netgear router. I would just turn on my pc and have internet. After my brother touched my computer it no longer recognizes any wireless connection. My internet provider says that I need a new router. I don't think that is the problem because after my brother played with my computer it was unable to see any connections (not even neighbors which I normally see). This makes me think something is wrong with my computer not the router.
PS. I do have my wireless switch turned to on. My brother doesn't know what he did but will not be allowed to play with it again.
View 10 Replies
ADVERTISEMENT
Oct 15, 2011
I just updated Cisco software and my external hard drive is no longer recognized by Cisco. It is a Seagate drive that is listed on the Cisco tested - passed - approved list. It worked prior to this update. I have disconnected the drive. Reconnected it. Rebooted. Turned machine and router on and off and its still not recognized.
Model name: Linksys E4200
Model number: E4200
Firmware version: 1.0.03 build 14
Operating system: Windows 7 SP 1
Software version: 1.4.11266.0
Connection type (WAN): DHCP
View 7 Replies
View Related
Nov 6, 2012
I just reformatted the hardrive on my old Gateway MA3 dinosaur laptop and reloaded Windows XP. Once loaded, no Wireless Network Connection icon appears in Network Connections and is not showing up as a Network Adaptor in Device Manager. The adptor is a Broadcom BCM94318MPG(802.11b/g) device on my. I have an XP CD and the original Gateway Windows XP CD and cannot get Windows to find the driver on the cds. Can't connect to the internet so I can't get anyupdates. Is there a way test the adaptor to see if it's cooked or not? Is there a procedure to get the machine to recognize the adaptor?
View 2 Replies
View Related
May 29, 2012
last week i noticed a lot of connectivity issues while surfing the web through wifi. my setup: dell vostro 3550, wireless adapter n1030, win7 64-bit after several attempts of fixing the issue following recommendations wrt the n1030 adapter (eg deactivating bluetooth, changing channels of router to 1 or 11, etc), I decided to complete erase all driver and hardware entries of the blue-tooth wireless adapter (like suggested in this thread: [URL]
afterwards i installed ALL available and latest drivers from dell or/and intel regarding this wifi adapter. the result is that the wireless adapter is again shown in the hardware manager and also in the system information of win7 which is great.BUT, somehow the win7 wifi network software/tools does still not recognize the adapter by the means of unplugging the lan cable i just see the wifi symbol with a red x. also opening the network and sharing console does not show the adapter to me although when clicking on "configure wifi networks" and "adapter properties" it is there and active "ready to use". additionally, the intel wireless diagnosis tool tells me that the adapter must have been deactivated or deinstalled. well, the tool is partially right, but the adapter was reinstalled and shows up in the hardware manager. somehow it missed that point ?
View 9 Replies
View Related
Apr 9, 2012
We had a little family get together at my house which involved 2 smart phones and an iphone-(people were browsing using our unsecured router) and now the wireless router is not recognized by our pc's; it's like the wireless address just disappeared.
View 1 Replies
View Related
Apr 7, 2013
I have a Linksys E1000 router which was working fine. My hard drive crashed; I replaced the hard drive and now my router is not recognized. I have reset it and tried to reinstall it with the CD. Nothing works.
View 1 Replies
View Related
Jun 20, 2010
I just got E1000 cisco wireless router. Started setup, everything worked fine and replaced admin password with my own. For some reason got error message. tried to redo setup and got message router not recognized. used laptop and found out that wireless works fine. After few days noticed that there is a (mynetworkname) guest connection you can connect without any password. i don't need that stupid thing and my question is how to disable guest network? I cannot reach Main Menu from cd and have no idea where to look for it when i connect to router by web.
View 9 Replies
View Related
Apr 8, 2012
I replaced a WRT120N router with a new one thinking that the old one was damaged. During setup, the router wasn't recognized. I used the same connection for a line from the internet to my LAN connectin and the line works fine. Connecting through the router is no good.
View 1 Replies
View Related
Feb 24, 2013
I have an EA2700 (fimware "classic" 1.0.14.129982) that used to work perfectly fine with a Comcast cable modem. I just recently switched to Charter with an Arris TM902 modem and that's where the problems started. The cable modem will not recognize my router. I have to plug in a computer into the cable model when it starts up. Then I need to clone the MAC address and restart the router (after disconnecting the computer). Why isn't the cable modem recognizing the router when I restart it? I guess this could work if it would be a one time thing but I had to power-cycle the modem and it stopped recognizing the router even with the cloned MAC address. So I had to do the whole spiel again.
Is there any way to make this work easier? Should I update my router's firmware to the "smart" one?
View 9 Replies
View Related
Aug 8, 2011
I have an E4200 wireless router and have bought myself an external hd for media sharing (STOR.E STEEL S 1TB disk (PA4252E-1HJ0). Unfortunately this disk comes with a Virtual CD partition on it, which can not be deleted or removed (url....)!! Despite this being massively annoying by itself it also renders my disk useless, as my router does not recognise the disk (to to the additional partition). Is there any possibility to extend the firmware or to provide a fix that allows me to use the partitions on the disk, despite this additional "virtual" device?
View 6 Replies
View Related
Jun 20, 2011
Yesterday i upgraded my e4200 to firmware version 1.0.02 (Build 13) after waiting since february.Unfortunately it still doesn't recognize my WD 500 GB Essentials.
View 9 Replies
View Related
Jul 30, 2012
I have a E3000 and just upgraded my Mac with the OS X Mountain Lion. I can't access my external HD anymore, although when I go to the router set up, on the storage tab, the router appears to recognize the HD.
View 9 Replies
View Related
Dec 22, 2011
My wireless router will no longer appear on the list of available networks, but it can find others. My partner's laptop will find it instantly! So it's obviously something on my computer.
OS: Vista Ultimate
Internet Provider: Sky
Country: UK
View 3 Replies
View Related
Feb 6, 2012
I have wireless internet at home through a Belkin router.It used to work fine but one computer wouldnt connect. I tried checking the security password on my laptop and ever since it won't connect. (However, now the other computer does!) It picks up the signal from the router but just won't connect. When I run ipconfig I get a message saying Media Disconnected. I've searched forums and can't find an answer to this.The laptop still connects to the wireless internet in my office so the wireless capability obviously still works.
View 3 Replies
View Related
Nov 25, 2011
I have a BEFW11S4 router when to put in password for the router and must have had a typo as I can no longer access router.Tried the factory reset on the rear of unit to no avail. Is their any way to get access as I have the main computer wire to the router. I need to get into the unit to move the channel number.
View 2 Replies
View Related
Jul 10, 2011
My Dell Dimension is no longer connecting to the internet via the wireless router. I have a dlink DI-524 and a dlink wireless USB key but it no longer connects. This just started today. When I try to repair the connection, it fails on "renewing IP".
OS is Windows XP.
P.S. I have tried power cycling the modem/router but nothing works. Other computers can get on the internet via the wireless router fine.
View 3 Replies
View Related
Nov 18, 2011
Been having random connection drops for the past few weeks where I would see the network connections to the router just drop either on a wireless connection or a wired cat 5 connection. As of tonight I cant connect to the router at all. If I disconnect and reconnect the power after 30 seconds it will come up for a short time but then I will lose it again. linksys as my router is out of warrenty. I'v searched around for similiar problems people have been having, but it seems like mostly involve just the internet connection. I still have the same firmware for the routers as the day I purchased it and the router sits on my desk in a ventilated area not overheating. I can do to further diagnose the problem, I have even tried resetting to factory defaults. I try to diagnose the problem or see if my router is just dead.
View 3 Replies
View Related
Aug 25, 2011
My E2500 was working great for the past 3 months, and now it seems to be broken since I cannot access the internet anymore. I can connect to the router via wireless or wired at 192.168.1.1 and play with all the settings. On the status page, I have entries for Internet IP Address, Default Gateway, DNS1, and DNS2 as though I was connected fine to my DSL modem.If I connect my computer to my DSL modem then I can access the internet perfectly fine, so I know the modem is working. However, if I connect the E2500 to the modem, and then my macbook to the E2500 then I cannot access anything other than the router config pages. I have also tried, from the router admin page, to ping "www.yahoo.com" and "8.8.8.8" to no avail.
I have tried without success:
1. Renewing IP address from the router status page.
2. Cycling the power on the modem.
3. Rebooting the router.
4. Unplugging the power from both the modem and the router for 10 minutes and reconnecting it.
5. Resetting the router by holding down the reset button for 30s.
6. Using a different computer.
7. Turning off the firewall.
8. Reinstalling the firmware (1.0.01 build 3 May 6, 2011)
View 1 Replies
View Related
Mar 20, 2011
I have a DVR connected to CCTV cameras that I would like to connect to my computer via Ethernet and a Netgear N150 router which also handles my broadband. A program called VideoViewer is installed on the computer which works with the DVR to view images on the computer via ethernet.it works with a Zoom router, but not the Netgear.
View 3 Replies
View Related
Jul 17, 2006
My lap top and other desktop are able to detect the internet but not my main computer with this router.
View 2 Replies
View Related
Dec 29, 2011
I mistakenly downloaded and installed version 4 firmware when i should have installed version 2. My system (windows ver. 7) no longer sees the wireless router (WRT54G). I no longer have the install CD and the version 2 firmware does not seem to be available on the website. Is my router now dead in the water?
View 1 Replies
View Related
Nov 14, 2012
I bought a Linksys E1000 wireless router a year or so back. it was loaded onto a computer that no longer works. i have the router and the box but no disc or manual. My laptop and ipad are working fine with the router but i can't get my iphone hooked up and dont think i have the correct password. I dont have any software on my laptop to even figure it out. What can i do to get my phone to use the router?
View 1 Replies
View Related
Sep 19, 2012
After I had Prism high speed internet installed (made by Cisco) and I can no longer print using my Dell V313s Wireless printer. I have lost the driver disc that came with the printer and Dell wants to charge me a large fee for support and Prism states that they are not responsible for the printer not talking to the computer.
View 3 Replies
View Related
Jul 7, 2008
I have had no problems with the WUSB54GS connecting to the WRT54GS up until last Friday...it can no longer connect to the router and reports that the network cannot be found.When i refresh the list of available networks i can "see" the router on the wireless PC but when an attempt to connect is made,it fails.OK,i rang up Linksys tech support today and we tried everything possible to work out what the problem was e:g uninstalling/reinstalling the software,updating the routers firmware,disabling security,trying all channels 1 thru 11,using WEP,using WPA,changing SSID name,using secure easy setup,using windows wireless configuration,changing USB leads nothing will make the device connect.
View 3 Replies
View Related
Jul 19, 2011
I have connected a Seagate Free Agent 500GB to the USB port of my E4200 and while it does work fine, When the drive has been idle for a while, it goes into power saving mode, turning the spindle motor off. This means it takes a few seconds to access the disk. Not a problem, but apparently, those few seconds are enough for either Windows or the E4200 to decide that the disk is no longer accessible. The share is still available, but I get missing folders and files, files won't open or are not found, and backups job with Acronis True Image will fail because it thinks the share is unavailable.Sometimes, constantly refreshing the view and opening files at random will revive the share, but often, the only way to get it back is to restart the computer.
The problem is definitely related to the power saving. If I leave a video clip playing or similar, so there's always some disk access preventing the drive from entering power save mode, it works fine. But 15-20 minutes of no disk activity immediately causes problems.
View 3 Replies
View Related
Mar 20, 2011
I have a DVR connected to CCTV cameras that I would like to connect to my computer via Ethernet and a Netgear N150 router which also handles my broadband.
A program called VideoViewer is installed on the computer which works with the DVR to view images on the computer via ethernet.
Funny thing is that it works with a Zoom router, but not the Netgear There must be settings on the Netgear that needs changing
View 9 Replies
View Related
Nov 18, 2012
password is not recognized bythe Linksys router
View 2 Replies
View Related
Aug 5, 2011
I have had my router for at approx. a year and a half and it has worked flawlessly. Now my PC which is plugged into the router still works fine, I'm just not able to connect wirelessly anymore. I've tried the basic things like unplugging and rebooting, nothing changes. The lights still say it is transmitting.
View 1 Replies
View Related
Nov 3, 2010
I had a simple PPTP VPN server running behind my old DLink router. When I installed the E3000 the VPN clients could no longer connect. The port forwarding for PPTP is turned on and VPN passthrough is enabled. The PPTP server reported GRE47 checksum failed. The linksys chat tech was not beneficial. How to get a PPTP route to work?
View 5 Replies
View Related
Feb 23, 2013
For some reason I can no longer make Wi-Fi calls with my E1200 router. I have checked with my ISP and T-mobil. They both tell me that everything on their respective ends is working correctly. The only piece of the equation is the router.
View 5 Replies
View Related
Jul 14, 2011
I'm trying to fix the network at a student housing building and the system is kind of a mess. We bought a new E4200 to replace our old Linksys router which no one knows the admin pw to. We have four switches for 50 connections throughout the four story house and when switching the connections over to the new E4200 all of the wired connections no longer work. Switch back to the old router and presto. How do I need to change the settings with the E4200 to get it to work?
Also, as it's a thick old house the E4200's wireless only covers maybe half of it...I purchased two wireless repeaters to put on the 3rd and 4th floors, are these simple to install with the router?
View 4 Replies
View Related
Dec 15, 2012
After updating the firmware of th EA6500 to Ver.1.1.28.146072 I have no longer access to the GUI options of Speed Test, Guest Access, Parental Controls, Media Prioritization and USB Storage. I have reset the router to factory default settings and still none of the items are showing on the web page the only options available are:Connectivity,Troubleshooting.Wireless.
View 5 Replies
View Related
Jun 24, 2012
I have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.
I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
At this point I'm assuming it's a Linksys issue since I know that my Verizon modem can connect me to the internet, so works properly. Is there some known incompatibility with this Linksys model and the Westell 6100G modem?
View 2 Replies
View Related
