Accessing Routers From 1 Point?
Jun 19, 2012i have a modem and 2 routers and then my computer. how do i set it so i can access the web GUI of each router no matter what router im plugged into?
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 3600 Accessing Wireless Access Point From Remote Subnet
Mar 28, 2013I recently installed a couple of Cisco Aironet 3600 Series Wireless Access Points at a remote site. While I was at the site everything seemed OK, The clients were able to get connected to the access points, the guest network worked fine, I could SSH into the access points, and I could ping them. The problem is when I went back to my home site I tried to SSH into the access points through an ASA IPSec VPN Tunnel and it couldn’t find it. When I try to ping the access points they “time out”. I can ping and connect all other addresses (via RDP, HTTP, etc..) on the same subnet which should rule out an access list problem. A couple of notes to be aware of:
The WAP’s have the Autonomous IOS installed (Version 15.2(2)JB) The WAP’s are connected to Dell PowerConnect 5724 (Not by choice.. We are a Cisco shop, these were already there and have plans this year to replace)
I can ping and SSH with Putty to the WAP’s from the local subnet I cannot ping or SSH from a remote subnet to the WAP’s. I can access all other IP’s and Computers from a remote subnet.
Cisco Routers :: RVS4000 / ISP WISP Point To Point Network Project?
Nov 30, 2012Currently in place ISP WISP Point to Point network would like some pointers to exceed in doing it right. Here are some issues.ISP Fiber 50 Megs down and 50 Megs up ( Working )What Router do I use? Looking at Cisco RVS4000 at JDT Site as main router I have routers at others towers using the 10.1.19.xxx address as wans setup.Do I pull out all routers and use only one from the JDT Site?
a. Due to Port forwarding
b. Lets say main Wan is 74.144.55.159 Lan 10.1.19.1
1. Site BTT router is assign address 10.1.19.33 Lan 192.168.6.1
a. Can I setup 74.144.55.159:85 to see 10.1.19.33?
My Point ot Point radio use different IP address to separate from lan address (10.1.19.xxx) Radios (10.1.119.xxx)1. Everything is working just want to re-design everything never thought I would grow this fast with in 2 years. Hope I explain this well enought. 90% of users are out in the country without high speed internet.
Routers / Switches :: Accessing Two Routers From The Same LAN?
Aug 20, 2011I have a little probs@a site .we have a vsat link connected to a linksys E1000 router which is pluged into a cisco 2950 switch doing DHCP to the LAN,then a WAN link configured on a cisco 2911 router on static ip which is pluged into the same switch to serve the same LAN.I have been having issues of the workstations accessing both the WAN and internet@ the same time.
View 1 Replies View RelatedAccessing Shares Between 2 Routers On 1 Internet Connection?
Nov 19, 2011I have the Apple Time Capsule connected to my ISP using PPPoE and it is working just fine creating a wired and wireless network. The IP address of TC is 192.168.1.1 and I have set it's DHCP range between .100 to .200Next, I wanted to add VPN to the router as I live outside the US and wanted to access some services in the US. So I got an ASUS router and flashed it with Tomato firmware.I assigned the ASUS as IP address of 192.168.1.10, connected this it to a LAN port on the Apple and used a DHCP type Internet connection to set it up. I then created a second WiFi Network and gave the DHCP range between .11 to .20Now using any Wi-Fi device, I can connect to either of these networks and browse the web just fine. The ASUS is all setup as a VPN client so any traffic going through the ASUS is through a US based VPN.
View 5 Replies View RelatedRouters / Switches :: Difficulty Accessing Internet Through Server
May 18, 2012I have a router and a server that are connected through two unmanage switches. The router has DSL service in it and I want to access the internet on the server but I can't. The two are in the same network and it is a static IP network. I can ping the router from the server.
View 36 Replies View RelatedRouters / Switches :: Accessing A QNAP Ftp Server Behind A Router
Jul 12, 2011I cannot seem to see my server behind a cisco router. I have a feeling it is because our network phone system may be robbing the IP address?We have two fixed IP addresses.The first one, is assigned to the router.We have two swtiches set up behind router and all the other network stuff interanally wrks great.We also have full internet access. When I type the IP in on the web, it accesses the talkswitch phone system.I have set the internal IP to the server as fixed.I have port 21 open for FTP.When I run a test, the internet sees port 21 open. However, I cannot seem to cal lup the server over the internet. Could the talkswitch system somehow be interfereing with the logon?What would the proper syntax be to access the server?
View 3 Replies View RelatedCisco Routers :: RV220W - When Accessing External IP Don't Get Routed
May 20, 2011I want to know whether NAT loop back is possible with the RV220W router/firewall, or when can we expect a firmware update that addresses this?For terminology sake, what I mean is that I've got a rule that maps HTTP/S to 192.168.1.2. However, when accessing my external ip from an internal ip, I don't get routed to 192.168.1.2.
View 13 Replies View RelatedBelkin Routers :: N600 Accessing Hdd On Usb Port Is Very Slow
Oct 19, 2012Accessing my hdd on the usbport is very slow. Have a n600 router. Can I boost this in any way?
View 2 Replies View RelatedRouters / Switches :: Accessing Router Logs After Firmware Flash?
Aug 29, 2011if i flash my firmware on my router, can i still view the router logs before the flash? i heard that .logs can be on the ram of the router.
View 1 Replies View RelatedCisco Routers :: WRVS4400N Accessing Local Services Via External IP?
Aug 7, 2011Recently I'm having issues with accessing local services via external IP. Short description of configuration:
- sub.mydomain.com pointing to my external IP.
- few web services running on my local server with reverse proxy on Apache 2
- firewall on router enabled
- ips on router disabled
- single port forwarding: WAN 80->Lan 443, WAN 443->LAN 443
- accessing my services via sub.mydomain.com/service1, sub.mydomain.com/service2, etc
- I had to create a new rule in internet access policy allowing LAN, any, any to
Basicaly if I go no matter if I type http or https I will be redirected on 443. That configuration has beed working without any issues for a month. Recently I have increased the amount of DHCP users and suddenly it's not working any more. I can still access my services from outside but not from LAN.Restarting router does the trick for a while,sometimes for few minutes, sometimes longer.Enabling IPS is the way to go but then I'm limited to around 22Mbit/s. I have no idea what happend.What I can't understand that it was working, suddenly it's stopped and there are two solutions, either to enable IPS or to restart router?
Cisco Routers :: RV180 - Setup VPN To Allow Users Accessing Via IOS Devices?
Mar 29, 2013I want to setup a simple VPN to allow users to access the office via the iOS (iPad/iPhone) devices. I assume I do this through:
VPN>IPsec>Basic VPN Setup
BUT, what do I enter for the "Endpoint Information" and "Secure Connection Remote Accessibility"?
Cisco Routers :: Join Network With RV016 To Network With RV082 Via Point To Point Air Bridge
Apr 19, 2012Due to bandwith requirements, we need to join a network with a RV016 to a network with an RV082 via a point to point air bridge. (VPN over adls was not cutting it) fortunatelly there is line of sight.
The info
LocationA LocationB
RV016 RV082
WAN1 ADSL modem WAN1 ADSL Modem
WAN2 DedicatedIP modem WAN2 Free
WAN3..7 free
[code]....
We need LAN-B endpoints to be able to reach servers on location A and viceversa.
We pre configured two point to point radios for the tower people to install. (we could change this configs)
Topology (crude sketch)[URL]
Our questions: best port to plug the radios into the RVs WAN ports? switch ports? What rules or static routes need to be created?
Cisco Wireless :: 3502p - Access Point Support MESH And Point-to-Point Bridging?
Apr 16, 2013I need to know if 3502p with outdoor antennas supports Point-to-Point Wireless Bridging?
View 6 Replies View RelatedCisco Wireless :: Point To Point Access Point 1262 Bridging
Feb 27, 2013How would I bridge a wireless connection with a distance of 400 feet? Would twoAP1262N-A-K9 be able to make this happen? Or is there another wireless bridge that you all can think of?I would be connecting one AP1262 of off a 3750g switch and at the far end (400 ft aproximately) another AP1262N-A-K9.
View 12 Replies View RelatedBelkin Routers :: Using F5D7230-4 As Access Point?
Dec 20, 2012Can I use my F5D7230-4 as an access point? I need to provide a hardwired ethernet connection to my A/V reciever but not have a wired port in the area of my house. I have an existing wireless router thru Century Link. Could I have the Belkin attach itself to the wireless network and then have a cat 5 come out of one of the four ports to connect my A/V reciever to the network?
View 1 Replies View RelatedRouters / Switches :: Use TEW-639 As A Wireless Access Point And Switch
Jul 6, 2012Here is my set up:
192.168.1.1 is a Linksys WRT610N acting as a router and DHCP server for addresses .100 to .150
192.168.1.2 is TEW-639 with DHCP turned off and connected to the Lynksys via one of the LAN ports.
I then have a FosCam camera with IP 192.168.1.010, connected either wirelessly or via a wire on a LAN port to the TEW-639W.
Here is my problem: If the FosCam is connected wirelessly to the TEW-639W I am unable to see it from any device connected to the Linksys. If I connect the FosCam via a wire to a LAN port on the TEW-639W then I can see it from a device connected to the Linksys device.If a device is connected to the network via the TEW-639, I can see the FosCam whether it is hardwired or wirelessly connected to the TEW-639. What am I doing wrong?Why can I not see the wireless connections on the TEW-639 from a Linksys connected device?,The setup is that the internet comes in and is connected to the Linksys, which then via LAN cable and LAN ports on both devices is connected to the TEW-639, which is then connected to the camera.
Linksys Access Point :: WAP54G - Connection Between Two Routers
Jan 21, 2011I have 2 WAP54G AP. I have office with internet connection near my home. How to connect these access points so i can get access to internet from home, but don't won't to anyone else can access that.
View 1 Replies View RelatedBelkin Routers :: 5FD8235-4 V2 - Access Point Setup
Feb 2, 2013If I want to setup my N+ router 5FD8235-4 V 2 as an access point. How do I go about doing that?
View 5 Replies View RelatedBelkin Routers :: F9K1102 V3 Access Point IP Error
Mar 23, 2013When I set up the Belkin F9K1102 as an access point I can no longer access it via the ip-address and it does not accept the new ip-address I've given it, but takes the ip-address 192.168.2.254, while my network is on the 192.168.1.XXX address series. The only way I can do this is by manually given the router a new address, then manually turn of the DHCP- server and finally move the internet cable from the WAN port to one of the LAN ports - but then the LED-indicator on the router is blinkin red.
View 2 Replies View RelatedBelkin Routers :: N600 - Access Point Addition
Dec 28, 2012I have a Belkin Play N600 as my primary and have an older Belkin G+MiMO that I'd like to connect as an access point only. Any step by step instructions of how to accomplish this?
View 1 Replies View RelatedRouters / Switches :: Configure SpeedTouch Router As Access Point?
Nov 5, 2011i have a LAN network between several pc's connected with several switch's and connected to Thomson SpeedTouch 510 DSL Router its ip address is 10.0.0.100 subnet 255.0.0.0 and the router dont give auto ip to the PCs i have to issign it manually to the PCs "static ip".I bought the acer android recently so i bought a tp-link td-w8901g wireless router to act as an access point so i connected the 2 routers to each other by LAN and gave the tp-link an ip address 10.0.0.12 subnet mask 255.0.0.0 so it will be the same ip range of the speedtouch and setuped the tp-link router to fit my isp configeration it worked at first but i had to reset the router so i did the same configuration i did before but didnt work and i cant access the internet using the android or the wireless but when i connect the phone to the tp-link and unplug the speedtouch the wireless works so theres no any problem with the router?
View 1 Replies View RelatedRouters / Switches :: Dwl G700ap Wireless Access Point Password Set?
Feb 4, 2011i have dlink dwl g700ap wireless access point.. router will show default and no password. i try to connect by ip 192.168.0.050 as per manual guide by cannot.my default gateway is 192.168.1.100 taking lan wire from builing internet that used cisco.
View 1 Replies View RelatedRouters / Switches :: How To Connect Router And Wireless Access Point
Mar 13, 2011I have high-speed cable access currently coming into an older D-Link 4-port wired router. I need to buy a new wired and wireless router so I can sync my new Android 4G phone (I'm in an area with bad cell coverage but I can sync with wi-fi). I have a second house about 200 feet from mine and have 3 Cat5E lines running underground in conduit to it so the lady next door and and her two kids can use the internet (I have 40-50mb service for my business use at home). Problem is that my kids have discovered YouTube, streaming video, video chat, etc. and are burning up my bandwidth. I currently have two of the lines to them disconnected so that I can limit their use to one computer at a time. I'm considering having them buy a Wireless Access Point, can they connect it to the standard single Cat5E LAN wire that is coming from my new wired and wireless router when I buy it?
View 2 Replies View RelatedBelkin Routers :: Configuring An Older 5FD8230-4 As Access Point?
Dec 16, 2012I am trying to configure an older Belkin Router (Model Number 5FD8230-4) as an Access Point so that I can boost the range of my network. The problem I have is in configuring the old router. It won't allow me to change any settings, or at least the changes don't stick, even after clicking "apply changes". I tried creating an administrative password but I am not even sure that this is working. I am using a Macbook, so perhaps this is an Apple compatibility issue. I have tried resetting the router and reverting to Factory default settings, but no joy.
View 3 Replies View RelatedBelkin Routers :: Setting Up Max N300 As Access Point With USB Drive
Dec 17, 2012I wanted to set Belkin Share Max n300 as an access point. I followed the instructions, set the IP address to the suggested one and connected it to the main router. It worked, computer connected to the Belkin via wire was getting IP address from DHCP on main router. But: The Belkin device itself became invisible. I lost connection to Belkin device via config page via HTTP. It does not respond to any IP address so I actually cannot use it for purpose I wanted to set up secondary Wi-fi, I just cannot configure it. Also I wanted to use USB ports of the Belkin to connect external drives. I cannot do it as well. More over it does not go back. It does not reset to the original router option.
View 2 Replies View RelatedCisco Routers :: RV180W Add Access Point With Roaming Support?
Oct 20, 2012I have a customer with a RV180w running the latest firmware. We are currently using the router as a router and to provide wireless access. We want to add wireless coverage and I am interested in our options. We have a ethernet backbone which we could use to give the new AP LAN connectivity. Can we buy another RV180W and use it in AP mode and provide roaming wireless connectivty. The client wants a guest and business WLAN so we will use the VLAN feature of the router. How do we configure the new AP? Do we need to use WDS? If we use WDS, can we still use WPA2?
View 6 Replies View RelatedBelkin Routers :: Configure N300 As Access Point - Unidentified Network?
Nov 9, 2012As per settings menu, I tried to give it an IP address but the new address is not accessible for further configuration. When I connected to the router it status changes to "unidentified network".
My primary network address range is 192.168.1.1 to 192.168.1.10. So I gave address to belkin as 192.168.1.100. But I can not access this address from both primary and belkin network.
Belkin Routers :: N300 Wireless Bridges Be Connected To Same Access Point
Nov 21, 2012Can 2 N300 wireless bridges be connected to the same wireless access point ?
View 1 Replies View RelatedBelkin Routers :: N600DB Using Router As Access Point / Range Extender
May 16, 2013I have a N600DB configured as a primary router. I got another playmax n600HD router which I want to configure as an access point that extends my network upstairs and allows me to attach some wired devices like my ps3. I followed the basic principles of setting as access point and my locally connected ps3 and NAS are communicating but no Internet access. How the 2nd router can connect to the internet?
View 2 Replies View RelatedCisco Routers :: RVS4000 / How To Make External IP Point To Internal Address
Nov 29, 2011Basically I have a group of static public IPs and I need one of them to point to an internal server IP address. This is for the RVS4000 router.
View 3 Replies View RelatedRouters / Switches :: Convert 2Wire Router 38000HGV-b As Wireless Access Point?
Jan 11, 2013I just switched over from AT&T Uverse to time Warner cable for Internet. I bought a Motorola Surfboard sbg6580. I have the surfboard hooked up and all is well. Now I would like to do in put the old 2wire from AT&T in a room upstairs and use it as place I can plug in the Ethernet cords and also transmit another signal. I have what's a called plug link that is plugged in down stairs and then another upstairs and it allows the Internet signal to run through the power lines. So it just about the equivalent of running a cord for down stairs to upstairs. So basically I just need to plug more then 1 thing upstairs that isn't wireless and I would also like to transmit a 2.4ghz signal upstairs and use my Motorola to transmit a 5ghz.How would I set up the 2wire to do this.
View 3 Replies View RelatedCisco Routers :: Connecting Amped Wireless AP600EX Access Point To WRSV4400n
Aug 10, 2012I am having trouble connecting the Amped Wireless AP600EX access point to my WRSV4400n. As soon as I plug the range extender into the router, instead of it receiving an IP address, it crashes the router. I have updated the router firmware to 2.021. I have checked the box in the WDS menu to "allow wireles signal to be repeated". I will check with Amped, but are there any known issues between this router and the Amped Wireless family of range extenders?
View 1 Replies View Related