I am struggling to connect my Airlink101 router to AT&T DSL router. Even though I see "connected" in router status, i am unable to get connected thru wire / wireless and browse.
View 1 RepliesThe modem Time Warner gave me several years ago was dying, I took it in, they gave me a Cisco modem, I plugged it into the computer, works fine, so then I plugged it into my airlink 101 wireless router, the computer recognizes the router but says there is no internet access, i.e. the modem and router are not communicating. Why would change of modem cause lack of communication with the router, is there something different about modems now compared with roughly 5 years ago? And what can i do to fix it so i can have wireless access again? If it matters, I have no protection on my wireless (because I never figured out how).
View 1 Replies View RelatedI successfully installed the AirLink101 AWLL6075 Adapter, however it cannot find networks because the Wireless Monitor section is always checked as being "Disabled". When I uncheck the box, a few seconds later it comes right back to Disabled with the check mark again.
View 14 Replies View RelatedI I use a Linksys E3000 router. Sometimes when I look at the network map I see a device called "Unknown." It appears as though the two notebooks sometime are going through this device to access the Linksys E3000. (I've checked when both notebooks are on and I can determine what devices are connecting directly to the router and what devices are going through this unknown device.) Is there any way to determine what this unknown device is?
View 5 Replies View RelatedI have a Thomson TG585 v7 router which is in bridge mode. I also have a NetGear DGND3300v2 router which I would like to connect to the Thomson (eventually I will purchase a switch and connect another device along with the NetGear). The problem is that the NetGear only has 4 LAN ports and no WAN ports, which I assume you would need to set this up.
View 4 Replies View RelatedI've installed a RV042 and my terminals cant even ping each other. They have Internet, but they cannot ping each other, or open network shares. It is not a dns problem becouse it does not work with the IP.
View 1 Replies View RelatedI recently purchased a new Belkin N wireless router, model number (F5D8236-4 V3), i am however trying to connect this router to my old Belkin G wireless Modem Router (F5D7632-4 Ver7000uk).Now i can't seem to get the N router to connect to the internet-after much faffing about i can get all the LED lights to turn blue-bar the wireless which blinks amber (i did this by turning the DHCP server off, and by using the same WEP code). I get limited connectivity wirelessly and wired, which basically might aswell just say no connection.
Taking the N router out of the equation, the g router can connect to the internet wired (it no longer seems to work wirelessly, and had a horrible range on it anyway). I use a PPPoE connection-all my ISP details are correct.how i can get the N Router to work wirelessly and wired.
I have a 4 port wireless router and a Ethernet router. 4 port are not enough and I want to daisy chain my Ethernet router off my wireless.I have 3 computers and streaming for TV. When I plug one port off my wireless router to my Ethernet router my computer cannot see it. What do I need to configure so my computer can see it.
View 1 Replies View RelatedWe have just got a new netgear router. Our Desktop PC , mobile phones, playstation all connect to it wirelessly with no problem. But although this Samsung Laptop shows as been connected to the new router it wont access the internet. I am using an ethernet cable at the moment. The laptop worked fine with the previous router which was also a netgear.
View 19 Replies View RelatedMy internet was running perfectly fine for the first 6-9 months, but recently has deteriorated to a mess (keeps getting booted on and off or slows to the point where it's virtually unusable). It seems to be the worst on weeknights and weekends.<removed by moderator - etaf>, For reference, I am running a Windows 7 machine, connecting wirelessly through a Netgear WNR1000 router. When connected to the router using an ethernet cable, it works perfectly fine. There is another wired device which works fine, so it's mainly the wifi connection. For my Windows 7 PC, the wireless cuts in and out (working fine now), and oftentimes drops me. I have to reset the router/modem multiple times just to be able to use it. My roommate who also has a wireless PC also has problems connecting wirelessly as well. Currently, I have IPV4 connectivity, but no IPV6 connectivity.
My ipconfig below:
Windows IP Configuration
Host Name . . . . . . . . . . . . : J-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Peer-Peer
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
I would like to use the router at my friends house. I have a laptop, how do I connect to his router using my laptop?
View 1 Replies View RelatedTwo days ago we received our new phone land line from Mediacom. We already had internet service from them so we decided to get a phone line. When they came over two days ago, we received a new modem, RCA DHG535-2. The issue we are experiencing is that the modem is not connecting to our rt n-16 ASUS wireless router. The modem works fine without the router but we need it for school work. The troubleshooter says "DNS is not available".A few things i tried was to unplug everything and reconnect them back from the modem to the computer.It usually works when i had trouble in the past but it seems nothing is working.
View 4 Replies View RelatedI have connected my Belkin54 router to my desktop modem now I'm having problems connect my laptop with the router. I'm getting a message saying my setting aren't configured with the router and I have no idea where to go to have the setting configured with the router settings,
View 1 Replies View RelatedI just bought a d link extreme n wireless router and I tried to install it with a Mac book pro so we could not use the setup disc and when we tried to use the 192 168 0 1 in the URL and used the set up automatically and th Internet light on the router was not blinking and the internet was not working
View 1 Replies View RelatedHow do i make my wireless router connect to another wireless router?
View 1 Replies View RelatedHow can i stop others from connecting to my router
View 2 Replies View RelatedI am new to VPN and have set a server up using windows XP's built in feature. I have tried to connect to the VPN from inside the router and it works fine. but I can't access from outside of the router. The computer will connect but then when on the "Verifying Username and Password" step the connection will disconnect with error 721: The remote computer did not respond. The router that i have is a Lynksys WCG200, I have tried turning all the security features off. Could my router just not be compatible with VPN?
View 9 Replies View RelatedI am trying to connect an old computer to my wifi router. The old computer is running Windows XP Pro sp2 and has an old wireless card in it. I have tried various methods to connect it to the router but have been unsuccessful.
View 3 Replies View RelatedI realize there are a ton of posts with this same title. I've tried them all! My computer tells me I'm connected to my D link router but says "no internet access". I have other devices (computers, phones, ipads) that are connecting via the wireless router just fine. Furthermore, when I connect the ethernet cable directly to the computer it still does not connect to the internet. I've reset everything with no luck. I'm running windows 7. Everything is set to obtain IP address automatically.
[code]....
I HAVE AN I BALL BATON iB lr6111a and i need to connect the same to a router but it has only one rj45 port since the router dont have a modem how can i connect it to a modem with only one port.
View 1 Replies View RelatedI got a new isp today and it worked with a new modem connected with a wire .. When I connected the router it wouldn't find the network so i connected the modem again with just the wire and it still won't go online.
View 3 Replies View RelatedI just had charter install a wireless cable modem into my house and it was put in my study. however, i would now like to get my xbox 360 running as well as the internet for my blue-ray player and tv. So i bought a wireless router.The modem from charter is called: Ubee wireless cable modem (from charter)The wireless router purchases is: Netgear N300 wireless router (wnr2000v3) I am trying to connect them wirelessly. Like I said above, my modem is in the study and the router is about 30 feet away in the living room area.
View 1 Replies View RelatedRecently reset a Linksys Router. The only settings I changed were the name of the Router, the password, and the security settings to WPA2. My computer is able to connect to the router and has internet access. However, my cell phone is able to connect to the router/wireless network successfully but the internet is not workingIs their a setting on the router that I need to change to ensure that my cell phone can access the internet
View 1 Replies View RelatedMy linksys router stopped connecting. Laptop says its available but won't connect. Have reset, reloaded w/CD, unplugged.
View 3 Replies View RelatedI recently set up a router to have wireless internet at my house, and I've been experiencing very slow internet speeds. My internet specs are below:
ISP: Comcast
Plan: BlastPlus, which supposedly gives speeds of up to 40 mbps
Modem: Ubee D3.0
Router: Cisco/Linksys E1200
Before we got the router we used a wired connection which could only have one person connected at a time. That connection was a good speed, though I don't know exactly how fast. It never gave us any trouble. Now that we connected our router, we can't even stream youtube videos or anything. Emails take a long time to open, and navigating web pages in general is very slow.
I have a new n series Belnet wireless router that can take a usb printer. I have a Lexmark 2200 Series 1 Printer (with usb connection). I have used this printer with my laptop (runs Windows xp) by connecting the printer usb directly. I have also connected my laptop to the wireless router. I have plugged the printer into the wireless router's usb port. Is it possible to access the printer this way? I do not know what I should do next. The laptop cannot access the printer through the wireless.
View 5 Replies View RelatedWireless card not connecting to router .This is what we have so far
[code]...
This issue seemed to be addressed previously, but wasnt sure if I should create a new thread or reply to the old one.
Have Dell 6400, run Win XP serv. pack 3. No red X or yellow ! under Device Manager. I did open up laptop, took out WLAN card, restarted laptop, turned off laptop, reinstalled WLAN card, restarted laptop.
[code]...
I bought an old IBM Think Pad laptop and i cant seem to connect to my wireless router. I have another laptop which connected with no problem just simply typed the wireless password in and all work fine and the same for my iphone. First problem was when I got asked for the wireless password it came up with a message say " The network password needs to be 40bits or 104bits depending on your network comfiguration".
View 2 Replies View RelatedI have laptop running Windows 7 Ultimate Edition and an other desktop system running Windows XP.The Laptop is connected to the internet via the router and the desktop is connected to the router via a LAN cable(not cross cable).Is there any way to link these systems together?
View 1 Replies View RelatedRecently, after a few hours my laptop suddently loses connection to the router and from then it keeps connecting and loosing the connection for a few hours. Sometimes it connects successfuly .This happens while my other pc, connected by cable to the router, works perfectly.The next day i open the laptop the internet works fine.I noticed ,when i had another router, that the laptop often had problems connecting to it while my pc was working. It would connect a lot slower after i would reset the router.I have Windows 7 Ultimate installed on both.
View 3 Replies View Relatedi ahve a dlink dir 615 B2 router and it wont connect to the internet. on day it was fine and working, the next day the internet led wouldn't change from the red light to the green light.i have tried resetting it about 60 times, while the laptop was on/off, while it was plugged it, while it was without power, while the internet cable was in, while it wasn't, while it was shut down and i reset it and the i pluged it in while resetting it...i dont know what else to do!! short of smashing the bejesus out of it. The internet works fine when i connect the cable directly to the laptop, I don;t have a cable modem or anything, just a plain old cable from the street to my house.
View 3 Replies View RelatedI am trying to set up a wireless medialink router in my office. I work in a big shared office building and do not have access to the modem.
I called medialink tech support and they said that everything should work fine but that most likely both the router and the modem need to go to through a "power-cycle" to sync up and then it should work.
how to fix this without resetting the modem? I have reset the router several times and started from scratch but it just keeps saying "Connecting...." I use a mac OS 10.6.8