I am trying to setup a LAN network using wireless router. I hv two network cards. One is connected to internet through ADSL modem. Internet is working fine.The other network card is connected to wireless router.I am trying to setup hotspot at for learning purpose.
View 1 RepliesCan my Laptop be used to setup a WLAN for gaming?
View 2 Replies View Relatedi wanted to know if i could setup a netgear wireless router to my ethernet cable that is coming out of the wall. is it as easy as plugging the cable coming out of the wall into the internet port on the router?
View 5 Replies View RelatedI have two netgear wireless modem / router. I want to connect my internet, NAS and Media player on one device (netgear modem/router) and want to link the other netgear in my bedroom and connect another media player and also use the internet via primary netgear modem/router wireless connectivity.
View 1 Replies View RelatedFirstly I cannot get my Linksys RE1000 to work with my network having tried the set up CD on 2 computers (mac and windows). The main router is a BT Home Hub 2.0
The main router is in the basement where out internet connection enters the house, also in the basement is our LAN board where we have ethernet cables extending to parts of the house. There is weak wireless signal from groundfloor up to the top floor so wanted to find something where I could plug into the ethernet port and it would broadcast an wireless network to the upper floors/areas with a weaker signal. Thought the RE1000 would do this job but i can't get it to do it wirelessly let alone connect it to the main router using a ethernet cable.
So, with the latest firmware update I could add a second e4200 to my network to use as a bridge or access point? What I need is another device in my living room that can pick up the wireless signal and dish out network connectivity to my receiver, xbox360, and ps3. With the new firmware update can this be done with a second e4200? How does one connect to each e4200 on the network for setup (dohave to change the default ip address of 1?)I just bought a trendnet TEW-687GA 450 mb/s wireless gaming adapter and a trendnet 5 port switch to accomplish what I mentioned above. I'm just wondering if there is an advantage to switching over to two e4200's. The trendnet adapater does not have a 5ghz channel.
View 2 Replies View RelatedI have a Linksys EA4500 setup on my corporate network for wireless access. I have enabled the guest network and from all I can tell it's on a seperate subnet from my internal network like it should be. 192.168.x.x My internal is on a 10.x.x.x network. I conenct to the guest network using a laptop and I'm prompted for a password to get to the internet, which I like. The one issue I'm seeing is when I'm connected to the guest network I can still do an RDP session to internal resources. How is this possible if the guest network is on a seperate subnet?I take a laptop which has not been joined to my domain, connect to the guest ssid, and then open an RPD session and enter an IP address for an internal server and it connects. Is there a setting to keep this from happening
View 6 Replies View RelatedI am trying to setup to wireless routers onto one network. One router is the ES4500 the other is the Apple Time Capsule. The apartment I am in has thick walls and because of this, there are some wifi gaps. Trying to set the second router in a different room to act as a wireless bridge/access point for the first router.
View 2 Replies View RelatedI am following instructions I found to set up my wirelss network, but am having trouble configuring my router. I'm specifically at a standstill, because I can't connect to http://192.168.1.1. I pinged the router and got a response and went to run/ip config to confirm I have the right URL for the router, but still not able to get to the URL.
View 1 Replies View RelatedI have two PCs connected to each other through a Wireless-N Gigabit Router (WRT310N). One PC is running Windws XP while the other is running Windows 7. At this point I do not have, or want, Internet connectivity. I would, however, like to call web pages on the Windows 7 PC from the Windows XP PC. The Windows 7 PC has php files that run C++ files to analyze files supplied by the Windows XP PC and I would like to send the results of the analysis back to the XP PC.The reason for this is that I am setting up a home based web site that allows users to run programs on my Windows 7 PC but I want to keep hackers from accessing files on my Windows 7 PC. So the XP will be connected directly to the Internet and the Windows 7 PC will only be connected to the XP PC.I can successfully ping both ways between the Windows 7 PC and XP PC. So I fire up FireFox (FF) on the XP PC and type the following in the FF URL box.
[code]....
The same happens when I replace the Windows 7 PC IP address with the Windows 7 PC name.I tried to set up a network between the two PCs with the MS network wizard on the XP box. It made a setup disk with a single file on it. I was supposed to run the setup file on the other PCs that are supposed to be on the network but, whe I did, I got the following message.Cannot complete the Network Setup Wizard,An error occurred during the configuration of the network on this computer.You can configure the network manually.
Was told by a HP technician that I could setup a .wireless home network for the purpose of having my iPad and iPhone 4 connect to my D100 HP printer. Installed the disc that came with my router and can't get passed the point that requires a password. All my devices recognize the router but everything requires a password which I am able to provide. Can this router be setup without having Internet access if so then how?
View 2 Replies View Relatedeven though I have successfully added the network manually, using the same settings as my other laptop which has no trouble connecting. So now, the network appears in my "Connect to a wireless network" box, but whenever I try to connect, it says "Windows cannot connect to *name of network*" So when I troubleshoot the problems, it states "Check your wireless settings. Make sure your computer is in range of *Network* and that the network settings match the wireless router or access point settings." I KNOW it's in range because my other computer is connected properly right next to this one. So it must be a problem with my network settings. Though I don't see how that can be because my settings on both computers are exactly the same, but one's connected and one's not. Could the problem simply be that I haven't logged on to my router online to add this computer to the network?
View 3 Replies View RelatedJust got a new EA3500, and plan to use its guest network feature to allow Internet access but not access to my LAN. Wondering if I can set it up so that users on the guest network bring up a particular website when they open their browser.
View 3 Replies View RelatedWas told by a HP technician that I could setup a .wireless home network for the purpose of having my iPad and iPhone 4 connect to my D100 HP printer. Installed the disc that came with my router and can't get passed the point that requires a password. All my devices recognize the router but everything requires a password which I am able to provide. Can this router be setup without having Internet access if so then how?
View 3 Replies View RelatedHow do I setup a WRT160N as a wireless adapter to connect a wireless printer to my network? I do not use the wrt 160 as a router because I have an AT&T router for u-verse connection. Also, I physically cannot wire the printer to the main router (opposite corners of the house).
View 2 Replies View RelatedI just installed my new Cisco E3000 and configured it over the HTTP interface, as I have on previous routers. I am unable to find any setting for the "Guest" wireless network (outbound internet only), or the Parental controls. Both of these are features of interest, and they're simply not listed in any of the web-based settings.
Puzzled, I did a Factory Reset and configured it via the Cisco Connect instead.. this had the Guest feature and Parental controls, but none of the other features I need, like QOS, or Port Forwarding, or DHCP disable.
It seems like the Web interface only configures some settings, and the Cisco Connect configures other settings, but I can't use them both.
Where does one set up the additional password for Guest access? Other than this, the router works fine on 2.4 & 5 GHz, nice..
I'm trying to set up an Iomega Home Media Network Cloud NAS and I'm having problems with opening ports 50500-50599. I have opened port 80 and 443 successfully and included the above port range above as well, but when I check it on www.yougetsignal.com the ports 50500-50599 are still closed. I even tried to split the range in two parts, and still no success. I have been in contact with my ISP and confirmed they do not block any ports in the 50500-50599 range and that the cable modem (a Motorola SBV5120) is operating in Bridge Mode.
View 3 Replies View Relatedi want to setup a wireless network with 12 pc
View 3 Replies View RelatedI want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies View Relatedi want to enquire how we can setup a network with 100 computer along with router, firewall, print server, file server. diagram of network to understand the things.
View 1 Replies View RelatedIs there any way I can tell if an network priority is setup on the router? The last week or so the internet has been unusually slow sometimes, and not slow at all other. I don't have a good relationship with my roommate (network administrator) and I feel she may have put a network priority on the router for her and or her boyfriends computer/s. Is there any way to tell? Is there a particular way in which the internet behaves when a priority is set? I just don't want to pay for the internet if it is not going to work most of the time.
View 6 Replies View RelatedI get an Ethernet cable from his router in my unit. I also have my own router. I was wondering if there is a way for me to create a private network for myself using my router and still have access to internet?
View 1 Replies View RelatedCannot setup NAT on edimax router I ve got this setup: [URL] It works well - I can connect from TESTPC and LAPTOP (bottom left corner) to SERVERS A/B/C (bottom right corner) without any problem. Everything seems to be routed perfectly, however from SERVERS A/B/C I cannot ping TESTPC and LAPTOP, and I can't even establish an RDP connection.I was told to setup static routes or NAT, but I am at a loss on how to do it. I am using an EDIMAX BR-6424NL wireless router ?
View 1 Replies View RelatedHow do I Find network security key after router already set up
View 1 Replies View RelatedFind network security key after router already setup
View 2 Replies View RelatedI have a dir-615 D-link router. It is well installed with my main computer that is an old XP windows system. I tried to create a network to give acces to my friend laptop when he comes home(he has a mac). I setuped a network with a name and a password. So my friend could find the network name and i gave him the password, but it never works. Another friend of mine also came with an older iBook laptop and the same thing happens.
View 5 Replies View RelatedSo I just setup a new router and got everything up and running...I got every wifi device connected, my iphone, ps3, laptop..except one laptop.Its a Windows Vista laptop, I can connect to the network but I cant receive bytes or load web pages. I can connect to the network but not the World, its blocked by an X...I dont know if vista laptop has the same ip as another device.. Cisco E1000
View 14 Replies View Related1 Virgin media home home up stairs in the home office. Ether cable running from the home hub, outside the house to the downstairs lounge with an ethernet socket on the end. Cable from the socket into a dlink router (set to operate as a hub).My reason for this setup was due to the rubbish wireless signal from the virgin hub, and the fact that I have various other bits of kit downstairs that I could use an ethernet cable with.The question is, IF my laptops are connected to the router downstairs by an ethernet cable and I want to transfer some files between them, will the data be routed through the virgin media hub upstairs before coming back to the router that both laptops are connected to downstairs? I have just done a test with 30gb worth of files and the transfer speed was 8.7MB/second, is that good for wireless?
View 1 Replies View Relatedinternet provided to whole building with connections in every room -> personal router in my room -> my PCs, Macs & printer, how to set up my computers so that they can share files with each other and print to my network printer, but without being susceptible to being accessed from other computers in the building? I have my own netgear router. But at the moment, my shared folders are accessible by everyone in the building, so is my printer If I set all the computers to automatically set ip by DHCP, they can access the net, but everyone in the building can access them (and my printer which requires a manual ip doesnt work). If I set all the computers to manual addresses (e.g. 192.168.1.14 ... 192.168.1.15 ... 192.168.1.16 etc.) they work with each other, the printer works, its secure, but I can't access the internet!Is there a way to for example have my own internal network with manual ip addresses, while also being able to connect to the net?
View 1 Replies View RelatedIt is the size of a 3 story townhouse but it actually has 5 floors, they aren't straight up I guess. The walls and floors are concrete so signal seems to be an issue for wifi connectivity. Right now my configuration is as follows:
Fritzbox 7390 - DSL Modem/router/N and G wifi located on 3rd floor
WRT160N - WAP/wired router in basement connected to Fritz box via G wifi and wired to PC and printer as well as a LAN over Power line
LAN over power line - only connected to Xbox at the moment on3rd floor to stream media from PC
I also have an Apple tv 2g on the 5th floor connected via fritz N wifi so I can stream iTunes media to a tv. The connection to the apple tv worked for a few days but now it seems to fail all the time. I tried streaming media to the Xbox as well as a PS3 over wireless but it always times out, that I why I am trying the LAN over power. I also tried sing a E3000 as a WAP but couldn't seem to get DDWRT to cooperate so it isn't being used right now.
how I can get this house better connected so I can have a reliable network throughout the house without breaking the bank? I am currently stationed in Germany, but am originally from the US so if I were to buy anything it would need to have an English interface, I am already having enough problems with the fritz box since it is only on German.
is it possible to setup a wired local area network using time capsule 2T as the router?
View 1 Replies View RelatedI have one desktop pc using a wireless connection thru a linksys usb for the net. I want to add a router and (1) pc and one cell phone and 1 laptop. I want to use the linksys and that computer as the main connection.I want to add the router and have other pc's and the cell connect to the router.I have an unused ethernet connection on the linksys pc (main one thats on the net now)I have a d link on the other PC in the house The cell phone gets wifi.I have one laptop with wifi that i want to connect I need a for dummies on this one, using XP?
View 1 Replies View RelatedMy son is trying to set up his (just received) ATT U-verse network but has only a Acer Android Tablet to connect to it. The instructions say to plug it (the modem) in to the computer but of course there isn't one on the tablet.
View 2 Replies View Related