Wireless :: Use Internet From 2 Wifi Adapters At Same Time?
May 11, 2011can i get better speed by using two wifi adapters at the same time
View 2 Repliescan i get better speed by using two wifi adapters at the same time
View 2 RepliesI have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View RelatedI hav two different internet connections by different service providers,one is LAN and other is WIRELESS.whn i turn off the WI-FI button n put the lan connection thn it shows connected but pages dnt open and a reload message comes and thn i unplug LAN n turn on the WI-FI conctn thn i m able to connect and surf.so, i m only able to use the wireless one..
View 2 Replies View RelatedIt is usually by a router or install a third party software without anyone saying if it works or not.
I have two connections at home. One is a Wifi ( public wifi for my village) that i use for my phone and the other one is a wired dsl. I have used both but not on the same time. I tried connecting them both ( phone have tethering) but I think they are interfering with each other making me lose connection. I am using vista home.
I have seen the merge connections( in network and sharing center) and i have seen this one [URL].. but I am a little bit wary of changing my registry.
I have to put cd in and run setup every time I want to get online. WHY
View 2 Replies View RelatedSo I just got hooked up to the internet via qwest the other day with my room mate. We have a wireless modem (PK5000) and he's using the AE2500 usb adapter to get online. Now, he can get online, but if he ever turns off or sleeps his computer, he can't connect when he turns it back on. His computer can see the network, full signal, but when he tries to connect it says cannot connect and under troubleshoot options suggests we should move his computer closer to the modem, but its only about 20 feet away and shows full signal. To get it to work, we need to go into the modem config and reset the wireless options. No changes are made, just scroll to the bottom and click apply, and presto change he can connect with no problems.He's running windows 7 home edition 64 bit. The modem's security is WPA/WPA2.
View 1 Replies View RelatedI have a Cisco WRT120N Router and a Cisco Valet AM10 wireless adapter. Almost every time the computer reboots, I loose my network and I have to redo the AM10 setup. The AM10 is the only device that loses the connection, my lap top and printer do not lose the connection.
Problem 2: Everytime I upplug and replug the AM10 a window pops up saying I need to check the drive for errors but none
are found.
Problem 3: I downloaded the AM10 install program, Downloadable.Setup.AM10.1.2.10148.2. It does not work. If I try to run it Iget an error message that the setup canot be completed and to call in for support.
Problem 4: When I can get it working is shows that it is Wireless Connection 5. Why 5 and not 1? Where are the other 4?
<script id="overlay_tmpl" type="text/html">// <div id="<%= overlayId %>" class="_mp3rocket_overlay_style" style="left: <%= overlayLeft %>; top: <%= overlayTop %>; width: <%= overlayWidth %>; height: <%= overlayHeight %>"></div> // </script>
I have 2 network adapter on my PC , but i cant use this 2 internet connection at a time, these connections are taken from main router. is it possible to increase my internet speed ? . i can use each connection seperatly, if one connection remove another will work,
View 2 Replies View RelatedRecently upgraded home router to Linksys EA3500 and a AE3000 Adapter for my laptop. Laptop is Dell Inspiron 1705 (yeah, it's old) running XP SP3. the adapter's drivers installed properly from the supplied CD as it negotiates and connects with the new router. However, there is NO Linksys Wireless Manager. It appears it was not installed at all. I can find no folder in Program Files named either Cisco or Linksys nor anything new in the Programs list. Is there a Linksys Wireless Manager included on the CD that should have installed?
Can I download it separately and install?I've disabled the built-in Dell wi-fi radio with came with an Intel ProSet wireless manager. Would REALLY like to have a new wireless manager that works well with the new adapter. Am going on vacation tomorrow and will have to deal with new and different access points, hotels, etc.
I've been having major issues with my wireless on this computer (randomly decides not to work while computers in the same room are fine) so I got a new wireless card to see what it could do. Installed it, everything says it's installed fine, but it will NOT detect any wireless networks. Not just mine, any of the 8+ networks I can usually detect from my room. I'm on Win7 Professional 64.
Things I've tried (and I'll be seriously annoyed if people reccomend doing them a 14th time, as I've already spent an hour on livechat with a support person telling me to do things I told her I'd already done):
Installed with 4 different drivers (the ones on the CD, the ones on the website, two versions directly from Ralink for the chipset) Tried both the manual and automatic "update driver" options in device manager. Uninstalled/reinstalled it like 4 times. Moved it to a new PCI slot.
Removed the old adapter before installing it. Removed the old adapter after installing it. Tried connecting to my network as a "hidden" network (which it's not). Installed only the driver and not the adapter utility, and used the utility. Installed the software before physically installing the adapter. Installed it after physically installing the adapter.
I'm at a loss. It doesn't detect ANY networks. No, it's not a problem with my network, there's more than a half dozen that my other adapter, in the same computer, can detect. And I don't know why. It has not ever worked properly. The antennae are on properly, nothing is interfering with it (though that would be odd since it's 3 inches from an adapter that can detect other networks). I might be willing to accept that it's just DoA, but that would be odd considering it installs just fine and reports that it's working just fine.
Just bought this Linksys AE3000 Wireless Adapter. I followed the directions, run Setup on DVD....then plug unit it.Adapter NOT Found!Unit Blinks Blue light every 8 seconds..
Note, that when first plugged in.......Device driver auto downloaded...and said ready for use. I gather through Windows 7
Region : Mexico
Model : TL-WR841ND
Hardware Version : V8
Firmware Version :
ISP : Telmex fiber
I use this router to replace the FO rooter that my ISP provides with the service as it's too limited (no NAT name translation, closes NAT, no uPnP etc...)
So the WR841ND acts as my main router, DHCP server, WiFi AP for all my network. My problem is that once in a while ( every 1 or 2 days) the wireless loses functionality, I still can see it from my devices, but can't connect, even fixing the IP (apparently not a DHCP issue then). The only way to fix this is to shut down the router 10 sec and restart it.
This brings another issue, I have another router (WR741) in WDS dispatching the signal to another part of the house to wired devices (Xbox , wd tv live hub) and it loses the WDS link, again the only way for this router to recover it is to restart it which is annoying.
I have a desktop PC with no wifi card that I want to use with a Clear Wifi hotspot. I have a WGA54AG Linksys Gaming Adapter and I want to use this with the desktop to access the wifi. I do not know how to reconfigure the gaming adapter for the CLear hotspot's security protocols.
View 1 Replies View RelatedI just got a WET54GS5 to use for game systems. i wa able to use the software in order to get the system online and working, but i am not able to access the wireless bridge though the web page. the username is blank and i put in the correct password, but it does not go through.
View 7 Replies View RelatedI try to connect my LinkSys wrt320n with Apple Time Capsule with mode "sahring existing wireless network" and so Time capsule doesn't work. It gets IP, but writes "isn't internet connection, WiFi network don't find" and also in the admipage of my wrt320 I can't see Time Capsule as client.
View 4 Replies View RelatedI have a router attached to my Dell desktop running Windows 7 and am trying to install the AE2500. Instead of using the router, I want the AE-2500 to access my HotSpot wifi on my cell phone. I go through the AE2500 installation and Device Manager shows it is installed properly. However, I do not see the adapter in my list of available wireless connections and I'm unabley to disconnect my router connection. I keep clicking disconnect but it never does.
View 1 Replies View RelatedI recently acquired a WMP600N-EU that is running under W7 x64 with the latest Linksys available drivers for download, which unlike the default MS ones, don't enable the Virtual Wifi adapter.Now with this new adapter, the wireless icon starts with the blue circle spinning, and the at the point the other adapter was already connected, it displays the "orange sun" (not connected, connections available) and stays there dead for some 10 seconds. At this point, my router's SSID is already listed. Only after that time it will start to successfully auto-connect to the pre-configured network, whereas windows has already finished loading or the browser launched unable to check mail.This is obviously not a functional fault on the adapter. If I didn't had the previous adapter to compare, I might find it normal. Btw, I've cleaned every previously stored wireless connections.
View 3 Replies View Relatedhave received an Cisco Model DPC3925 modem/router from UPC (provider in the Netherlands) and they allow me to have 120Mbit connection, but with my own WIFI Adapter I only received between the 40Mbit/60Mbit speed. My question is the following; Wich WIFI adapter is the best adapter for my Cisco Model DPC3925 modem/router?The distance between the modem/router and my pc is not that much. And when I use an cable the connection is between the 90Mbit/110Mbit. The WIFI adapter that I now use is the: TP-Link TL-WN881ND. I was thinking to buy a Linksys AE1200, but I dont know if that adapter is much better then I already have.
View 6 Replies View RelatedI have a compaw CQ61 that is using the operating system windows 7 64x.
The problem occurred today when logging onto windows. Windows tells me that the connection i have to the router is limited. Other devices i have in the house are capable of connecting to the wifi router. When deleting the connection and trying to reconnect to the router, it brings up the message that it is taking longer than expected to establish a connection and then eventually brings up the message "limited connetion"
When trying to connect the laptop to the router via cable, it doesn't even recognise that it is connected and does not establish a connection.
When using the windows connection troubleshoot, it detects a driver problem with both the wifi adapter and the Lan adapater. Therefore i uninstalled and reinstalled both devices but still suffered the same problem.
When clicking the connection i am attempting to connect to, right click status, details.. everything is in blank, it gives no information regarding to the connection.
Any good suggestions for a quality wifi adapter ? Everything I've used so far has been terrible.
View 1 Replies View RelatedI have wifi laptop that I want to use for video to tv but obviously only using about half of download speed of hardwired desktop pc. Can I use ethernet cable hardwired on laptop while it is wifi or will this interfere with connection?
View 2 Replies View Relatedi have two networks accessing through Wi-Fi..if u want to access resources of A network from B then what should i do...means i have installed SQL database server on A network & want to access on Network B
View 1 Replies View RelatedI just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
View 5 Replies View RelatedI am running XP SP3 with .NET Framework 3.5 SP1. The wireless network adapter works fine using either the Atheros Client Utility (my preference) or Windows Zero Config, Since someone mentioned the latter as possibly being necessary, I have been using it for these tests. It is, thus, not surprising that the wireless network adapter is present in and shows no problem in the Device Manager (devmgmt.msc), or ipconfig output; however, Xirrus WiFi Inspector shows "No adapters available" and does not function. How to get WiFi Inspector running?
View 2 Replies View RelatedWin 7 Home Premium. My vpn connection to work disconnects my wired internet connection. Is there a way around that? If not, can I force the vpn to connect wirelessly while staying wired to my home network and internet? Is it even possible to have both connections active at the same time? Vista laptop uses only wireless and has no problem staying conected while using vpn.
View 5 Replies View RelatedI have a WET610 that I intend to use to connect a PC to the local network and further on to the Internet. The local connection works, I can ping to and from the computer connected to the WET610 and I can see the other computers, both wired and wireless, on the network so the wireless connection is ok but I can't connect to the Internet, I can't even ping the DNS I'm using. What can be wrong? All the other computers can access the Internet. The WET610 talks to a wireless AP which in turn is connected to a router
View 9 Replies View RelatedI cant get it to connect to internet, it keeps giving me an error message. I have windows 7 and Linksys WiFi Router E2500
View 1 Replies View RelatedAI have a Dir-825 router. The 5GHz is turned off and the wirless is on G/N. I have shawcable for my isp and my firmware is 2.06 and its a Rev B Router. I also have Qos Engine on for allowing me to have 2 xboxes on Open NAT.problem is my wireless signal for some wired reason is VERY weak. A while ago it used to work really far way outside. It was around 150ft distance at 4 bars. Now for some reason I can't even go upstairs without getting a 1 or 2 bar signal.
View 3 Replies View Relatedi have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
I am trying to install a Belkin N600 to a Windows 7 desktop with no luck. When I run the setup off the install disk it attempts to install the driver needed for the N600, but every time it fails the install stating that the device is not functioning. When I connect the N600 to my computer it sees the device but its almost like my usb ports are not powering the device even tho I have connected a lash drive to all of my ports to make sure they were working, and they are( All usb ports are 2.0).
View 2 Replies View RelatedI have a curent cable connection that is fine connecting two computers through a router and it is wired. I have a new Iphone and some programs "documents to go" for example won't sync to my computer thru USB cord it wants a WiFi connection. Can I have both a WiFi and wired conection on same cable connection? I'm asuming if I get just a WiFi router, I will also have to get new nic cards for desktops, when all I really want is something for the Iphone to WiFI thru
View 1 Replies View RelatedI am facing a proble in wireless connection speed that is getting very slow at a specific time, i.e., from 12pm to 2pm and from 9 pm to 2 am. The service is unlimitted type contract
View 1 Replies View RelatedI can't connect on my 2500 on my xp system. I just wiped the drive and did a fresh install on everything due to a virus. I updated xp/ and drivers and installed the ae2500 drivers. When I try to log on it starts to and shows connected however, it tells me "windows was unable to find a certificate to log you on to the network" I noticed that this system has the same ae2500 with windows vista and uses wpa2-personal, aes. The xp system only has options for wpa-personal, aes. Is this the problem or is it something else?
View 1 Replies View Related