WNR2000 - 2 Netgear Routers To One Modem?
Jun 9, 2011
So here's the setup, my apartment is right next to my parents' house (don't ask why) and they have a netgear WNR2000 router in their upstairs loft connected to a modem going to a local internet provider. My apartment is just far away enough so that I can barely get a signal, so I'm trying to set up a second wireless router (netgear WNR1000v2) in my apartment that will connect to the internet through the first router so I can get a better signal. I do have a way of running an Ethernet cable from the first router to the second in my apartment.
View 3 Replies
ADVERTISEMENT
Aug 9, 2011
I have two routers. One is Netgear WG602 v3 and Netgear WNR2000. WG602 v3 is connected with internet. I want to make a wireless bridge. How?
View 1 Replies
View Related
Jan 14, 2013
I just installed DD-WRT, version DD-WRT v24-sp2 (03/18/12) std, in a Netgear router model # WNR-2000V3 and so far everything is running good except for the LAN ports which are not working. I don't know what settings I have to change to get it working and I tried a lot of options from the DD-WRT site. I want this router to be an access point but it seems like I can't use the LAN ports at all whatsoever. Could it be that this firmware is no good? If so, is there a way to revert back to the factory NetGear firmware?
View 3 Replies
View Related
Jun 29, 2012
I'm trying to use a Netgear WNR2000 router as a repeater, I have a Netgear WGR614v9 as the main router in my house. I have followed online guides as closely as possible but am still having troubles. My main router is working fine, everything can connect to it and gain access to internet despite having to change the security to WEP to allow for the repeater function to work. Now I am having troubles getting the repeater (WNR2000) to connect to my main router. The ip address of the repeater is listed in the connected devices of the main router and everything is managing to 'find' the repeater just fine but when I connect and put in the WEP key there is no internet connection. I read that a static ip address is needed or something like that but I am completely baffled
View 1 Replies
View Related
Apr 27, 2012
Netgear wnr2000 download driver
View 1 Replies
View Related
Feb 6, 2011
ok so i finally got a decent dsl modem, from our isp it is also a wired/wireless router, i have Netgear WNR2000, that is conencted a lan port on the dsl router/modem, how do i set it up as an acces point so i can access the ip range of the dsl modem/router?
WNR's ip range : is the 192.168.1.x
Dsl modems's is: 10.0.0.x
I need to connect a computer which right now is at 192.168.1.x to my domain controller which is at 10.0.0.x..
View 9 Replies
View Related
Feb 17, 2011
I have a Motorola SBG901 router/gateway that is hooked to my desktop. I recently purchased a Netgear WNR2000 to use as a router to connect to a Blue-Ray player to receive firmware updates wirelessly. On every attempt to access the netgear unit to set it up as a repeater, I get nowhere. I tried hooking the unit up to my laptop and login in under the admin account but again to no avail. I really don't want to have to disconnect the SBG901.
View 9 Replies
View Related
Jul 22, 2011
ok I have logged in my router & clicked the repeater mode. whats the next step. BTW I am a complete newby to networking.
View 4 Replies
View Related
Jul 4, 2011
I have a similar problem to thread with same name dated 31-Jul-2010-that is now closed. I'm using Qwest internet with Actiontec PK5000, and I have to use my Netgear WNR2000v3 as a repeater.The Netgear is working as a repeater however I can't get internet through the LAN connections on the repeater. After checking the settings over and over again I'm beginning to think the repeater will only work with wifi. I need to hook up my desktop in the office, DirectTV, and Blueray player LAN connections to my repeater.
View 1 Replies
View Related
Jun 1, 2011
How do I personalize the settings on my router from default. Netgear wnr2000.
View 2 Replies
View Related
May 25, 2012
Our ISP provided a DSL modem/router (Netopia) that I connected to the Netgear wireless router with dd-wrt flashed. All I've done so far is connected the two. I have a connection, but I want to know if it's possible or advisable to configure everything from the Netgear router. But following the instructions here[URL], it seems I have to configure DNS and such using the Netopia router. I don't have a full grasp on how to use them together the correct way - like using the Netopia as an ethernet bridge.
View 4 Replies
View Related
May 23, 2012
Today a bought a brand new Netgear WNR2000 router.Upon setup the wifi was working correctly. All of the lights where active and it seemed everything was in order.Because the power cord was in the way I moved it and plugged it into a different powerpoint. From then onwards my router has not been working. Only three of seven lights are active (green).
I have tried unplugging and replugging all network cords. I have also turned it on and back off, reset the router and run the initial installation program thrice.What should I do now? Nothing so far has effected it. The computer I am installing it on is running Windows XP and the laptop I intend to use the wifi on is Windows 7.
View 1 Replies
View Related
Sep 29, 2012
Here is my setup:
Netgear WNR2000 router.
Macbook Pro with Snow Leopard connected to router through wireless.
Windows 7 Desktop getting internet through the MBP ethernet.
I can't figure out how to be a part of my "Home Network" with my Win7 Machine so I can see other computers in my house, use my networked printers, etc. I can only see the MBP it is connected to in network panel. I want to be able to stream the movies on this computer to my iPad which is connected to the wireless router.
View 8 Replies
View Related
Dec 5, 2011
I replaced a Netgear router with a similar Netgear router, but the LAN is no longer working.The old Netgear router would drop internet, but LAN would work. Replaced it, the new Netgear router works fine with the internet (cable modem), but the LAN with two computers will not work. The desktop with Windows XP, and a laptop with Windows 7. After runing network setups on both computers several times, I have been unable to reestablish the LAN, however internet access via the router is working. Reinstalled the old router and the LAN works fine, allowing file and printer sharing. Old router is a Netgear WGR614v2, new router is a Netgear WNR2000how to reconfigure the router/computers to get the LAN working again with new router.
View 8 Replies
View Related
May 2, 2011
i am unable to configure my netgear router with my clear modem
View 1 Replies
View Related
Apr 14, 2012
Lately I encountered random Internet connection issues?My router is a Netgear Wireless ADSL Firewall Modem Router DG834 (Firmware V1.05.0) and my ISP, isn't the most reliable regarding bandwidth... All clients (max 3 at the same time) connect wireless.The problem is that the last few weeks my connections is very unstable, all clients lose the internet connection until you restart the router manually.I can't even connect to the webinterface (192.168.0.1), during the downtimes.
View 4 Replies
View Related
Apr 18, 2011
I am hard wiring a Netgear wireless modem DG834G to the LAN connection on my PC. The modem lights up, the internet light flashes then goes green and the connection to the PC is lit. My PC wont see the modem - when I type 192.168.0.1 it cannot access the Netgear setup page. I have tried swapping the cable and even bought a PCI Lan card and installed it but the modem wont work in either port? I've had the modem checked out and it works fine it's just something in my PC stopping it from seeing the Modem. At present I have a USB modem hard wired which works fine. I unplug this when trying to setup the NEtgear modem...
View 6 Replies
View Related
Aug 23, 2011
My Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
View 1 Replies
View Related
Aug 26, 2011
I have Windows 7 64 bit.I bought a Netgear DGN2000 approximately two years ago. It is working well.Currently, there is good connectivity between my laptop and the modem/router (wired and wireless).I worked on my desktop this morning, uninstalled some programmed, but must have uninstalled a driver or something.I inserted the Resource CD, which installs the modem (although it is installed). Then it stalls at some point.If I troubleshoot, it states “Windows do not detect a properly installed network adaptor.
View 3 Replies
View Related
Sep 24, 2011
I am experiencing constant DNS issues page not found errors after about 10 clicks it seems to work, and actually get to the page, sometimes it takes longer or i may have to resete the modem again for my system to work, now i have a computer lan buisness with 10 computers connected to it and the internet speed is 4 mbps, i have called the internet provider they did some test, and the modem seems fine they have changed my modem 3 times for that reason , so i know its not the modem , i have switched cables connected to the modem, i use to own a hub i thought that was the problem, so i bought a NetGear's FS116 switch and the problem persists, i have switched over to different inernet browsers , that didnt work, changed my computers modem to assigne ip addresses , and that didnt woerk, also changed my dns servers from my modem by the ones provided by my service provider , and that didnt i am stuck. i have a 15 ft cable connected from my modem to the switch. and all my computers connected to the switch, the problem seems to be more when i have more then 5 computers running at the same time. i have also switched the 15ft cable and the problem still persists, error not found could me a config with the lan settings or dns error
View 3 Replies
View Related
Dec 11, 2012
How do you connect a usb modem to a wireless router?
View 1 Replies
View Related
May 27, 2011
I am using NetGear DGN1000 router which includes ADSL modem. I bought another router (Linksys E3000) with I connected to the old one. I would like to setup port forwarding on the new one and use the old one as a modem only. How can I do that?
View 3 Replies
View Related
Mar 8, 2011
For 3 years my Pantech 190 modem has been plugged in to my Dell desk top and internet access for my Dell laptop has beem shared thru a Netgear router .
I purchased the new Verison 290/4G modem. It workrd great until I tried to print on my HP printer thru the network. No luck.
Verizon says that the 290 is not a dial up modem, but instead looks like a network adaptor and the desk top doesn't want to run two networks - the Netgear and the 290. In other words, the 290 will not work on a system that is connected to any other network.
View 3 Replies
View Related
Sep 10, 2011
I have a Magnavox Blu-Ray player, model MBP5130/F7. I leep getting the DHcP cannot be acquired.
View 4 Replies
View Related
Dec 1, 2011
My wife bought her self an xbox last night so we can game togher. We both tried to get online last night, but came up with a strict nat for one of the machines. Which ever machine got online first got the open nat type. i've tried DMZ host with port forwarding for both machines to no success. We have a netgear modem router from charter cable. the model number I believe is CG3000D. she was on a wireless network and i was wired straight to the modem router.
View 3 Replies
View Related
Mar 21, 2011
My laptops internet runs super slow, but only at our house.It runs at top speed on any other network. My wifes laptop has no issues at all. Have done multiple virus check with multiple different anti virisus programs.We use a Netgear modem I usually connect wireless, but have connected with an Ethernet cord with no change in speed.
OS Version: Microsoft Windows 7 Home Premium , 64 bit
Processor: Intel(R) Core(TM)2 Duo CPU P7450 @ 2.13GHz, Intel64 Family 6 Model 23 Stepping 6
Processor Count: 2
RAM: 4063 Mb
Graphics Card: ATI Mobility Radeon HD 4650, 1024 Mb
Hard Drives: C: Total - 463711 MB, Free - 389512 MB; D: Total - 13026 MB, Free - 2178 MB;
Motherboard: Quanta, 3628, 18.42, CNF9401DLR
Antivirus: AVG Internet Security, Updated and Enabled
View 3 Replies
View Related
May 25, 2011
I cannot get my computer to recognize my Netgear WNR1000. I have called Netgear to explain the issue and was on the phone with them for 45 minutes.They did get the laptop to work but my desktop still does not. They told me it was a browser error. If I disconnect the ethernet cable from the router to my computer everything works perfect.I tried to reinstall the CD that came with the router and as I try to get through step 2 it says no router detected.I think this is my hold up but I have no way to know how to fix this. I tried to go on the Netgear website and they tell me that I have to be able to connect to the internet to download through the router. Well I can't do that because obviously that is the hangup. If I click on my Network Connections. It shows my computer connected to a Network with limited capability and then a big red X going to the internet.
View 3 Replies
View Related
Nov 26, 2011
I have set my WLL modem to connect automatically to my laptop when switched on. It does connect and work well until there is another modem in the neighborhood coming online.The task bar icon shows I am still connected but the connection is gone. I tried troubleshooting the network, reconnecting from laptop giving the passkey, log off and log on but none of these work, except restarting the modem. This has become a pain and has been so since I purchased this 4 months ago.Is there a setting change that can be done?
View 1 Replies
View Related
Apr 12, 2011
I bought the Netgear N300 WNR2000v2 today for my laptop (ACER Aspire 5552). Installation was fine but when in try to connect to the router i get a message "Windows was unable to connect to 'SSID Name'. However when i go into routerlogin.net and change the security options to 'None' i get connected to the internet no problem.
View 4 Replies
View Related
Feb 23, 2011
Cannot connect to Internet. Have a Netgear DGN2000 modem-router. Using XP Pro, AT+T ISP.Get to 'admin','password' page and sometimes get to Setup wizard but never able to finish it.AT+T checked line and said it was OK. Took all filters off phone lines and only have phone jack with router hooked up to it, so no interference is there. Just have DSL, 'dry loop'.Lights on router are (Green)Power,(Green) Port, (Green)Wireless,and (Green)blinking DSL, (RED) Internet light. When I leave router on these are the lights. Must turn router off so I can use Netgear unsecured network for internet on a wireless laptop running Vista.
View 3 Replies
View Related
Jan 27, 2012
I am relatively good at installing and troubleshooting smaller sized networks... I am having trouble with one of my customer's networks and I think I have the problem narrowed down. r issues.I have a customer with a FS726T switch and ~20 computers connected to this switch running DHCP assigned addresses.The switch is assigning addresses in the 10.0.0.xx rangehe customer currently has an old T1 line coming into a Cisco router, which then directs traffic to port 20 on the switch.The problem is, we are replacing the old T1 line with a newer 50mbps cable connection.The cable company pre-configured their router with a static IP address the 68.116.xx.xx range. The Subnet is also different than the Netgear's subnet. I would like to keep the old T1 connection in place. I believe they have data that needs to go to their mainframe/backbone server at corporate.
I cannot log in to the cable modem. IT is an SMC SMCD3G with a staic IP. I tried changing my PC's IP address to the same gateway but cannot get into the cable company's modem, even using a static IP with the same gateway as the modem's gateway address. I don't want to reset the modem/router and lose the cable company's settings.I am pretty sure for the devices to communicate, the following has to be true?:1) Cable modem and FS726T must be on the same 10.0.0.xx IP range?2) Cable modem and FS726T must be on the same 255.255.255.0 subnet mask?
View 7 Replies
View Related
Feb 3, 2013
Buffalo Linkstation HD-H250LAN and Netgear N300 DGN2200v3 ADSL2 Modem Router.
3 PCs connect without a problem, 2 wireless and 1 wired, but cannot get it to recognise the Buffalo Linkstation. Netgear uses 192.168.0.1. but Belkin used 192.168.2.etc.
Linkstation setup says Linkstation not connected, but it is.
View 3 Replies
View Related
Jan 1, 2012
Actually I've a WiFi enabled (Nokia) Mobile phone. I also have a internet enabled USB modem (HUAWEI) & a Netgear Wireless router.I am using internet with this USB modem in my desktop PC at home.But now I want to use internet in my mobile phone. So, I bring that wireless router.
View 3 Replies
View Related
