Netgear WNR2000 / Router Is Not Working - Only Three Of Seven Lights Are Active?
May 23, 2012
Today a bought a brand new Netgear WNR2000 router.Upon setup the wifi was working correctly. All of the lights where active and it seemed everything was in order.Because the power cord was in the way I moved it and plugged it into a different powerpoint. From then onwards my router has not been working. Only three of seven lights are active (green).
I have tried unplugging and replugging all network cords. I have also turned it on and back off, reset the router and run the initial installation program thrice.What should I do now? Nothing so far has effected it. The computer I am installing it on is running Windows XP and the laptop I intend to use the wifi on is Windows 7.
View 1 Replies
ADVERTISEMENT
Jan 14, 2013
I just installed DD-WRT, version DD-WRT v24-sp2 (03/18/12) std, in a Netgear router model # WNR-2000V3 and so far everything is running good except for the LAN ports which are not working. I don't know what settings I have to change to get it working and I tried a lot of options from the DD-WRT site. I want this router to be an access point but it seems like I can't use the LAN ports at all whatsoever. Could it be that this firmware is no good? If so, is there a way to revert back to the factory NetGear firmware?
View 3 Replies
View Related
Feb 1, 2013
I picked up a second hand NETGEAR FS750T switch today for very little as the previous owner said it had stopped working.
After powering it up, there is a small noise for about three seconds. All the lights above the 10/100 ports are solid green and I can't access the web interface when connecting it up to my computer.
What could the problem be? I've heard others with different switch models reporting that all the lights are flashing and replacing the capacitors fixes them.
I've tried the reset and factory reset buttons. The reset just puts all the lights off for the duration of holding it and the factory reset appears to do nothing.
edit: when I turn it on, all the lights and the sound starts immediately. After two seconds, the lights go out. After three seconds, the sound stops and the lights return.
View 1 Replies
View Related
Jun 29, 2012
I'm trying to use a Netgear WNR2000 router as a repeater, I have a Netgear WGR614v9 as the main router in my house. I have followed online guides as closely as possible but am still having troubles. My main router is working fine, everything can connect to it and gain access to internet despite having to change the security to WEP to allow for the repeater function to work. Now I am having troubles getting the repeater (WNR2000) to connect to my main router. The ip address of the repeater is listed in the connected devices of the main router and everything is managing to 'find' the repeater just fine but when I connect and put in the WEP key there is no internet connection. I read that a static ip address is needed or something like that but I am completely baffled
View 1 Replies
View Related
Jul 22, 2011
ok I have logged in my router & clicked the repeater mode. whats the next step. BTW I am a complete newby to networking.
View 4 Replies
View Related
Jul 4, 2011
I have a similar problem to thread with same name dated 31-Jul-2010-that is now closed. I'm using Qwest internet with Actiontec PK5000, and I have to use my Netgear WNR2000v3 as a repeater.The Netgear is working as a repeater however I can't get internet through the LAN connections on the repeater. After checking the settings over and over again I'm beginning to think the repeater will only work with wifi. I need to hook up my desktop in the office, DirectTV, and Blueray player LAN connections to my repeater.
View 1 Replies
View Related
May 25, 2012
Our ISP provided a DSL modem/router (Netopia) that I connected to the Netgear wireless router with dd-wrt flashed. All I've done so far is connected the two. I have a connection, but I want to know if it's possible or advisable to configure everything from the Netgear router. But following the instructions here[URL], it seems I have to configure DNS and such using the Netopia router. I don't have a full grasp on how to use them together the correct way - like using the Netopia as an ethernet bridge.
View 4 Replies
View Related
Sep 29, 2012
Here is my setup:
Netgear WNR2000 router.
Macbook Pro with Snow Leopard connected to router through wireless.
Windows 7 Desktop getting internet through the MBP ethernet.
I can't figure out how to be a part of my "Home Network" with my Win7 Machine so I can see other computers in my house, use my networked printers, etc. I can only see the MBP it is connected to in network panel. I want to be able to stream the movies on this computer to my iPad which is connected to the wireless router.
View 8 Replies
View Related
Dec 5, 2011
I replaced a Netgear router with a similar Netgear router, but the LAN is no longer working.The old Netgear router would drop internet, but LAN would work. Replaced it, the new Netgear router works fine with the internet (cable modem), but the LAN with two computers will not work. The desktop with Windows XP, and a laptop with Windows 7. After runing network setups on both computers several times, I have been unable to reestablish the LAN, however internet access via the router is working. Reinstalled the old router and the LAN works fine, allowing file and printer sharing. Old router is a Netgear WGR614v2, new router is a Netgear WNR2000how to reconfigure the router/computers to get the LAN working again with new router.
View 8 Replies
View Related
Jun 9, 2011
So here's the setup, my apartment is right next to my parents' house (don't ask why) and they have a netgear WNR2000 router in their upstairs loft connected to a modem going to a local internet provider. My apartment is just far away enough so that I can barely get a signal, so I'm trying to set up a second wireless router (netgear WNR1000v2) in my apartment that will connect to the internet through the first router so I can get a better signal. I do have a way of running an Ethernet cable from the first router to the second in my apartment.
View 3 Replies
View Related
Apr 27, 2012
Netgear wnr2000 download driver
View 1 Replies
View Related
Feb 6, 2011
ok so i finally got a decent dsl modem, from our isp it is also a wired/wireless router, i have Netgear WNR2000, that is conencted a lan port on the dsl router/modem, how do i set it up as an acces point so i can access the ip range of the dsl modem/router?
WNR's ip range : is the 192.168.1.x
Dsl modems's is: 10.0.0.x
I need to connect a computer which right now is at 192.168.1.x to my domain controller which is at 10.0.0.x..
View 9 Replies
View Related
Feb 17, 2011
I have a Motorola SBG901 router/gateway that is hooked to my desktop. I recently purchased a Netgear WNR2000 to use as a router to connect to a Blue-Ray player to receive firmware updates wirelessly. On every attempt to access the netgear unit to set it up as a repeater, I get nowhere. I tried hooking the unit up to my laptop and login in under the admin account but again to no avail. I really don't want to have to disconnect the SBG901.
View 9 Replies
View Related
Jun 1, 2011
How do I personalize the settings on my router from default. Netgear wnr2000.
View 2 Replies
View Related
Aug 9, 2011
I have two routers. One is Netgear WG602 v3 and Netgear WNR2000. WG602 v3 is connected with internet. I want to make a wireless bridge. How?
View 1 Replies
View Related
Jul 17, 2011
I went online with a tech real quick before I found I beyond complimentary tech support. They say my router is working like a switch. I cannot get any wireless access and to the three direct connections to the router only one is working. The lights are constantly blinking, with the power light blinking every so often
View 1 Replies
View Related
Oct 17, 2011
I have the Asus P5QL-VM DO motherboard.On the Ethernet port the lights are not working and I can not get an internet connection.
View 1 Replies
View Related
Feb 5, 2012
I pressed the reset button on my netgear router (WGR614 v7) and now the wireless light will not go on and i can't connect to it because I don't have a ethernet cable.
View 2 Replies
View Related
Sep 2, 2011
When I first got my Netgear N-150 router, the wireless speed on it was great. However several days passed and I started to notice the speed was decreasing; because I have HughesNet (I hate it) I thought this was the ISP's fault and called them and they said my speed had not gone down. During the day, the signal is fine and is at full bars and the speeds are OK. During the evening/night hours the connection becomes faulty and the laptop will disconnect from the network altogether. If I plug the ethernet cable directly into the router, the speed is OK also. I have taken the security off the connection to see if it will make any difference; it doesn't. I don't know if I need to buy a new router or what. I know my way around computers and routers (not entirely though) and I cannot figure it out. I have 2 laptops with Windows Vista both with home Premium.
View 11 Replies
View Related
Feb 7, 2012
I have two routers set up. It goes from the modem through a WRT54G2 to a WNR2000. I have one pc connected to the WRT54G2 that gets 20Mbps and another connected to the WNR2000 thats only getting 5Mbps. I realized recently I have them connected to each other wrong. Or so I assume. I have the fourth port on the WRT54G2 connected to the internet port on the WNR2000 and it's set to "Automatic Configuration - DHCP" and "DHCP Server" is enabled. From what I read one or both of those is supposed to be set to manual.
View 2 Replies
View Related
Jun 10, 2012
I am working on a network which has two ISP connections (Active/Active) terminating on router (ASR1000). From the LAN side (6500 switch) all the traffic need to be route on ISP1 but some of the specific subnets like 10.250.0.0/16 need to be route on ISP2 connection.
I am planning to use PBR and NAT with route maps. any documents or refrences are provided.
(access switches)---------(core switch)----------(routers)----------------(ISP1)
----------------------(ISP2)
View 1 Replies
View Related
Sep 13, 2011
I recently replaced a Linksys wireless router with a Netgear wireless router(provided by Comcast) to the modem in my house. I used my HP Pavilion as the computer to run the setup disk and the wireless wizard to link the new router to the modem. I unplugged my HP from the router and proceeded to setup my computer on the wireless network.
View 14 Replies
View Related
Jul 6, 2011
I have a windows 7 computer and have installed a netgear wg111v3 it worked for a while but now it has stopped working.
It detects wireless networks still but cannot connect.
View 5 Replies
View Related
Jun 4, 2012
Will not connect to the internet wired or wirelessly. It does turn on however. Not ISP or modem, because when comp is plugged in directly to the cable modem, internet connection works fine. I'm using a Comcast cable connection.
Router is Netgear-N 150 router wnr1000 version 2.My antivirus software is Malware bites, and when I ran it, it didn't find anything.
OS is windows 7 home premium 32 bit.Here's IPconfig:
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:windowssystem32> ipconfig /all >c:ipconfig.txt
C:windowssystem32>ipconfig /all[code]......
View 14 Replies
View Related
Feb 7, 2013
I own a Netgear Router and the wireless capabilities are not working. I have it connected to a comcast arris Modem. When i have and ethernet cable connecting my laptop, router, and modem, i get a connecting. but im not sure how to get the wireless running. I have used this router before ith my old internet provider. Ive tried messing around with the router settings for a while but i cant get it working.
View 1 Replies
View Related
Jul 17, 2012
I have a pair of ASA 5520s operating in failover pair as active/standby, having two contexts on them. I am planning to share the load and make it active/active making first context active on the primary unit and second context active on the secondary unit. My question is if this will disrupt any connectivity thru these firewalls when I do "no failover" on the active/standby and assign the contexts to different failover groups and enable the failover back.
View 6 Replies
View Related
Jan 2, 2013
Just finally updated my ancient belkin modem to a Netgear D3600WiFi modem router which works really well. However. I have a old G5 Mac without wireless so have always connected through my old belkin modem with Powerline adapters over my house wiring circuit:confused. Unfortunately the powerline adapters no longer work although both lights are flickering on the units. Netgear say they should work.
View 1 Replies
View Related
Jan 5, 2012
[CODE]My router stopped working when I tried to connect my new Samsung Smart TV to the wireless network by using the menu on the tv. I had to go and press the WSL button on the router. I pressed what I though was the WSL button and now my router doesn't work. I has three lights lit up, the power on light, a small green blinking light and an amber light by the number 1.I've gone to the Netgear website and they want $69 for assistance to get my router up and running. I can buy a new router for that much money. There has to be an easier way.
View 2 Replies
View Related
Sep 18, 2012
I had a wired router (dlink) that worked fine until it died. So I bought a netgear wndr 3400 v2 wireless router.I can connect to the wifi with my phone, but not with my desktop (running vista home basic).I called my isp, and we went through all the physical set up and that was fine, but it still said unknown network....he said it was that vista was not recognizing my new router....Here is my ipconfig /all business
Microsoft Windows [Version 6.0.6002] Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:UsersLindsay>ipconfig /all
Windows IP Configuration
[code] .....
View 14 Replies
View Related
Apr 10, 2012
I am having BSNL broadband & netgear router. Some of the sites are not opening like [URL] many more?
View 4 Replies
View Related
Nov 27, 2011
I have had the Netgear 3300 Dual Band for three years. Everytime I wanted to access using my laptop, I had to choose between 2.4G and 5G connection. For about a month now, the 5G does not show up. It doesn't show up as a network to select no matter what device I use. I have reset the router and updated the firmware. Both connection lights are blinking. I recently purchased and IPhone 4 and still I do not have the option of selecting 5G.
View 4 Replies
View Related
Jan 30, 2013
i have Dell inspiron laptop windows 7 operatinbg before my internet was working very well but in last 3 months i have been struggling alot with the internet browsing problem, my internet is connected and actvie, skype, yahoo eveything, torrent download is 100% working but when i open any browser the error message comes that CANT OPEN THIS PAGE MAY BE INTERNET CONNECTION NOT CONNECTED. i did all antivirus and reinstall the windwos but still the problem is active.
View 4 Replies
View Related
Mar 31, 2013
implementation of the cisco CSS 11501 boxes available as spare on our site into production for an application evry thing worked as expected. i was able to telnet the active/master box and was able to console both master and backup box from the console port.however a week post the activity im faced with this weird problem where im not able to take console or the telnet access of my primary/active box.The boxes are working in BOX-to-BOX redundancy and now im not able to telnet or console my active/master box. The telnet and console window prompts me for username and password and after entering the credentials nothing happens. no prompt or no error message is displayed.
The telnet primary authentication is via tacacs and secondary is via local. however for console im not using any method for primay authentication and local for secondary authentication. however i can successfully console my backup box. below are my obsrvations 1. the left and right status LED on the active CSS box is OFF.- it means my CSS 11501 failed and has no power. 2. upon firing the rcmd command with show line command on backup box i see that the telnet sessions and console session is established with the master box3. the redundancy state of the active box says it is master and has not changed state since my last activity, no application issue reported, all the services are active on the active box and also i can ping the active box ip address from my backup box over which box to box redundancy is established. This confirms the active box is functioning well 4. i initially thought the telnet sessions are not getting cleared, however the show line cmd with the rcmd cmd on the backup box confirms this is not happening. now im stuck as the active box cannot be accessed at all via console or telnet. i was thinking of below steps to be carried out.1. to failover the boxes and make the backup as master2. then try to take the faulty box off the network and troubleshoot (are there any other commands that i should use to troubleshoot)3. if nothing works try rebooting the box and check
NOTE: the software running is version 7.20.30.3 with standard feature set. we are not using cvdm or the CSS GUI. we could access the css initially on CSS gui and that is also not working now.
View 1 Replies
View Related
