NetGear Router Not Working With Direct Connection?
Jun 4, 2012
Will not connect to the internet wired or wirelessly. It does turn on however. Not ISP or modem, because when comp is plugged in directly to the cable modem, internet connection works fine. I'm using a Comcast cable connection.
Router is Netgear-N 150 router wnr1000 version 2.My antivirus software is Malware bites, and when I ran it, it didn't find anything.
OS is windows 7 home premium 32 bit.Here's IPconfig:
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:windowssystem32> ipconfig /all >c:ipconfig.txt
C:windowssystem32>ipconfig /all[code]......
View 14 Replies
ADVERTISEMENT
Apr 12, 2012
We have FIOS at our home. All the wall connections for ethernet are wired to the control panel in our house which are then connected to a wired router. We have another wireless router in the upstairs which gets internet through the wall port and it works fine.We had another downstairs wireless router in the living room that was working fine as well, but I reset it for certain reasons and it no longer works properly. All the proper lights light up: internet, port, power but the computer can only connect to the network and not the internet for some reason.
View 9 Replies
View Related
Aug 8, 2011
I have been using a WRT610N router for several years. A couple of weeks ago I purchased an iPad 2. I am not sure if its a limitaion of the iPad 2 or a wireless connection speed issue, but when watching You Tube music videos the video stops frequently and I have to hit the play button again to resume. This occurs more often if I am using Blue Tooth connected headphones than direct connected headphones, leading me to the initial conclusion that I am witnessing the limits of the iPad 2 processor. However, I recently downloaded the Speed Test app and have discovered that the wireless download speed varies from about 11-15Mbps, depending on the location (normal vs next to router). If I go to that web site and run the speed test there from my direct connected PC (connected to 1Gbps port), I get a download speed typically of 36Mbps (inflated I know because Comcast speed supposedly is limited to 25 Mbps).
View 2 Replies
View Related
Oct 31, 2011
My internet went down temporarily last week and ever since my computer has not been able to maintain a connection. It will pick up the signal intermittently but produce painfully slow internet and then promptly lose the signal all together. The wireless connection is working perfectly on laptops and smart phones, even when in the same position from the router as my PC.
Router: Netgear Dg834Gv3
Wireless Adapter: Netgear WG111v3 USB
Computer: Dell Vostro 200
ISP: AOL
View 2 Replies
View Related
Dec 9, 2011
I have my internet hooked up to a DSL Modem and a Wireless Router. But I had configured the Wireless Router wrong that I couldn't connect to it using a WiFi. I was going to reconfigure it but the Netgear Router was outdated that their reconfiguring URL no longer existed. So I went out and got a *NEW* Netgear Router. Prior to the *NEW* Router I had a Laptop and a PC connected via DSL Cable connected in the Wireless Router. Now with the *NEW* Router I had just purchased I connected everything just like I had done with my previous Router. Wireless Connect works great but I can't connected using the DSL Cable connection. It does not respond. I tried connecting the cables to different ports but it didn't work. My PC mainly needs the wired connection cuz it's where I play my Online games. I tried playing with my Wireless connect but it lags very bad. How to get the wired connections to work? Netgear N600 Wireless and Dual Band Router
View 3 Replies
View Related
Aug 3, 2011
So from a security standpoint... PPTP through Windows RRAS then RDP to the server?,Open port 3389 to the server and rdp direct? would think that having a VPN out front would block people from attempting a connection, but if the VPN username and RDP username are the same, I feel like its about the same.
View 7 Replies
View Related
Apr 10, 2013
I have a computer with special software, customer abroad has a Laptop and connect multimedia center via etherner port to this laptop, I want to connect directly to customers ethernet port so I can program that multimedia center using a software in my PC. I know the ip address of multimedia center, but I cannot ping to it then I use hamachi port bridging.
View 1 Replies
View Related
Feb 13, 2013
APs must be directly connected to the 3850 for it to work in MA or MC mode. But if we add some switches and configure it to work transparently (without CDP/ VLAN tagging /LDP ) ? Do you think this is really not possible to make it? What impact CAPWAP tunnel gets from this transparent switch ?
View 10 Replies
View Related
Aug 31, 2012
Dell Inspiron 518 I have a problem with my internet going direct to modem, it a constant problem with my internet. I use Internet Explorer 9 for my web browsing. I contact my ISP and they send in a technician to see if it was a problem with my modem, while the tech work on my modem he explain to me that there wasnt a problem with the modem. He showed a comparison with my computer and his laptop. when he used his laptop it show outstanding speed, and my computer was showing time out or webpage can't be displayed the only way i can use my computer for internet is if i boot up my computer and hold down F8 to go under safe mode with network and my internet works prefectly fine, i even try a ping testing under command prompt and website that test my ping, download speed and upload speed.
View 4 Replies
View Related
Jan 17, 2013
I just got another DCS-930L. I have set these up to work wirelessly before but my question is why can't I connect it directly to my ethernet port and be able to get into the web interface by typing the default IP address without using a utility or installation software? I have tried to assign a manual IP to it but that didn't work. So here is what I want to do: Plug the camera into the ethernet port of my MacBook Pro and just view what the camera sees.
View 7 Replies
View Related
Feb 24, 2013
I received a 5508 WLC, that I wanted to configure as a guest anchor for our DMZ. I stepped through the console configuration. Now that the setup is complete, can I attach my laptop directly to the copper SFP, and access the WLC web portal? I gave my laptop an IP address, in the same subnet, but still can't connect to the portal, or ping the WLC IP address.
View 2 Replies
View Related
Feb 5, 2012
I pressed the reset button on my netgear router (WGR614 v7) and now the wireless light will not go on and i can't connect to it because I don't have a ethernet cable.
View 2 Replies
View Related
Sep 2, 2011
When I first got my Netgear N-150 router, the wireless speed on it was great. However several days passed and I started to notice the speed was decreasing; because I have HughesNet (I hate it) I thought this was the ISP's fault and called them and they said my speed had not gone down. During the day, the signal is fine and is at full bars and the speeds are OK. During the evening/night hours the connection becomes faulty and the laptop will disconnect from the network altogether. If I plug the ethernet cable directly into the router, the speed is OK also. I have taken the security off the connection to see if it will make any difference; it doesn't. I don't know if I need to buy a new router or what. I know my way around computers and routers (not entirely though) and I cannot figure it out. I have 2 laptops with Windows Vista both with home Premium.
View 11 Replies
View Related
Jun 3, 2012
Currently have two laptops: one is a MacBook using OS X, the other a Gateway PC running Vista Home Edition. A Dell Inspiron 17R notebook running Windows 7 Home Premium is in process of delivery. Current laptops linked on a home Wi-Fi network with AirPort Express router. Anticipated use of new Dell notebook requires its direct connection to Internet outside of current network configuration. Is it possible to have both accesses available in my setup utilizing my one cable high speed service connection? If so, what are the steps needed to accomplish the required setup?
View 1 Replies
View Related
Feb 3, 2013
I have a DROID X2 and a HTC DROID Incredible can I use wireless wi-fi connections directly through my BN450D router or do I have to go through my computer to hook up..
View 1 Replies
View Related
Apr 2, 2011
Currently, my customer has 2 units of Cisco PIX 515E running on Active/Standby mode. As for the heartbeat link, there are 2 dedicated switches placed in between both the Cisco PIX 515E i.e. FW1 --> SW1 --> SW2 --> FW2.
My customer will be changing both the Cisco PIX 515E to Cisco ASA 5510. Now, they are asking me, since they will be using Cisco ASA 5510 eventually, can the heartbeat link be a direct UTP cross cable or must the 2 switches in between still exist?
I remember I have tested this before, few years back, in the event I were to pull out the UTP cross cable that's connecting both the Cisco ASA 5510 Firewalls directly (without any switches in between), the Active/Standby mode still works fine. It doesn't go bad whereby both the Cisco ASA 5510 suddenly becomes Active/Active, and causes network issue.
Are switches required for the heartbeat link in a Cisco ASA environment or can a direct UTP cross cable connection be adequate.
View 3 Replies
View Related
Sep 4, 2012
I bought new Lenovo IdeaCentre H430 pc and I'm having problem with high pings. Windows 7 with on-board realtek NIC. Fresh install, fully updated, drivers installed from included CD. When I start pinging router (direct 1Gb ethernet connection, 1 hop), pings start at <1ms (which is fine) and after a while they jump to 300-1000ms.
I loaded up live ubuntu to test if the problem might be in HW. It's not, in ubuntu pings were always <1ms.I also noticed that when I start using connection somehow, pings go down to 1ms, but go back up when I stop using it (tested by accessing live camera feed on LAN).
Power Options set to max performance. I disabled Interrupt Moderation on the NIC, didn't work.I tested it in the safe mode with networking, same problem there.
It slows down our client-server based programs, what's causing it. All I could google up was that disabling Interrupt Moderation would work, it didn't though.Computer is giving high pings to router when idle and normal pings when network is under load, it slows down our software significantly.
View 2 Replies
View Related
Sep 13, 2011
I recently replaced a Linksys wireless router with a Netgear wireless router(provided by Comcast) to the modem in my house. I used my HP Pavilion as the computer to run the setup disk and the wireless wizard to link the new router to the modem. I unplugged my HP from the router and proceeded to setup my computer on the wireless network.
View 14 Replies
View Related
Jul 6, 2011
I have a windows 7 computer and have installed a netgear wg111v3 it worked for a while but now it has stopped working.
It detects wireless networks still but cannot connect.
View 5 Replies
View Related
Feb 7, 2013
I own a Netgear Router and the wireless capabilities are not working. I have it connected to a comcast arris Modem. When i have and ethernet cable connecting my laptop, router, and modem, i get a connecting. but im not sure how to get the wireless running. I have used this router before ith my old internet provider. Ive tried messing around with the router settings for a while but i cant get it working.
View 1 Replies
View Related
Jan 2, 2013
Just finally updated my ancient belkin modem to a Netgear D3600WiFi modem router which works really well. However. I have a old G5 Mac without wireless so have always connected through my old belkin modem with Powerline adapters over my house wiring circuit:confused. Unfortunately the powerline adapters no longer work although both lights are flickering on the units. Netgear say they should work.
View 1 Replies
View Related
Jan 5, 2012
[CODE]My router stopped working when I tried to connect my new Samsung Smart TV to the wireless network by using the menu on the tv. I had to go and press the WSL button on the router. I pressed what I though was the WSL button and now my router doesn't work. I has three lights lit up, the power on light, a small green blinking light and an amber light by the number 1.I've gone to the Netgear website and they want $69 for assistance to get my router up and running. I can buy a new router for that much money. There has to be an easier way.
View 2 Replies
View Related
May 23, 2012
Today a bought a brand new Netgear WNR2000 router.Upon setup the wifi was working correctly. All of the lights where active and it seemed everything was in order.Because the power cord was in the way I moved it and plugged it into a different powerpoint. From then onwards my router has not been working. Only three of seven lights are active (green).
I have tried unplugging and replugging all network cords. I have also turned it on and back off, reset the router and run the initial installation program thrice.What should I do now? Nothing so far has effected it. The computer I am installing it on is running Windows XP and the laptop I intend to use the wifi on is Windows 7.
View 1 Replies
View Related
Sep 18, 2012
I had a wired router (dlink) that worked fine until it died. So I bought a netgear wndr 3400 v2 wireless router.I can connect to the wifi with my phone, but not with my desktop (running vista home basic).I called my isp, and we went through all the physical set up and that was fine, but it still said unknown network....he said it was that vista was not recognizing my new router....Here is my ipconfig /all business
Microsoft Windows [Version 6.0.6002] Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:UsersLindsay>ipconfig /all
Windows IP Configuration
[code] .....
View 14 Replies
View Related
Apr 10, 2012
I am having BSNL broadband & netgear router. Some of the sites are not opening like [URL] many more?
View 4 Replies
View Related
Nov 27, 2011
I have had the Netgear 3300 Dual Band for three years. Everytime I wanted to access using my laptop, I had to choose between 2.4G and 5G connection. For about a month now, the 5G does not show up. It doesn't show up as a network to select no matter what device I use. I have reset the router and updated the firmware. Both connection lights are blinking. I recently purchased and IPhone 4 and still I do not have the option of selecting 5G.
View 4 Replies
View Related
Aug 15, 2011
I have a Netgear wgr614v7 wireless router that has been working perfectly for a couple weeks now, but I have suddenly run into a problem. For some reason, I can now only connect one laptop at a time to the network. When I try to connect a second laptop, it says, "Windows was unable to connect to [network name]". When I try to connect with my Macbook, it says "network timed out".
View 3 Replies
View Related
Jul 17, 2012
In my hotel, it is currently running a free internet, through ethernet port/cat5 wire When i plug the wire into my port, the internet works fine, as i am sending this message now, However, when i plug the cable into my router, and i try to connect to the internet, it gives this message through chrome Error 105 (net::ERR_NAME_NOT_RESOLVED): Unable to resolve the server's DNS I'm currently running through the google free dns, i've cloned my mac address direct connect works, however router does not.
IPConfig Logs, direct connected to the internet through wire and connected to the router.
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsLarry Wong>ipconfig /all
[Code].....
View 3 Replies
View Related
Jan 7, 2013
For some odd reason l cannot connect to Router as keeps losing connection. I connect for a few secs then it loses connection. I can use my IPAD fine to connect to router. I have tried to use use both wireless dongle and cable to connect to ADSL router but no luck with both. I have check for spyware etc but nothing found. I get a cross on my network connectivity icon in network connections with control panel. I am using Windows xp xp2 patch , drivers and patches are upto date. Device drivers upto date also Netgear router?
View 3 Replies
View Related
Apr 24, 2011
I'm posting from my phone because right now its my only access.I have a Netgear Router model number WNR2000I have a Gateway GM5260 model computer using windows xp.I am currently trying to connect to my awesome neighbor's wifi connection that they so lovingly bestowed on me and my family the other day.Herein lies my problem:I cannot get their router and my own to connect. I'm a networking noob and could really use some assistance.I've got a their wireless password, my router, and my ethernet cable connecting my router to my pc.Do I need to pick up a wireless antenna to connect to my router as well?
View 1 Replies
View Related
Aug 20, 2011
I am trying to remotely access my PC from my HP Touchpad. I have program to do that but my public router is blocking access. The program says to redirect that router to port 5900. Since it is a public router I can't find how to access the public router to redirect it.
View 3 Replies
View Related
Aug 4, 2011
I live out in the country at the end of a very long copper cable and my internet connection is never great at the best of times. Also live in an old house with thick walls so the family are always complaining about the poor wireless connection.So I bought a new router, netgear DGN3500, which on the whole seemed pretty good out of the box, but now it is randomly dropping the internet connection. Sometimes this is solved by rebooting the router, but just now this didn't do it and only turning it off completely for 30" and turning it back on again gave me back my connection (DownStream Connection Speed 3680 kbps, UpStream Connection Speed 416 kbps - which is as good as it gets on the end of my phone line).
View 12 Replies
View Related
Aug 15, 2011
I have a Netgear wgr614v7 wireless router that has been working perfectly for a couple weeks now, but I have suddenly run into a problem. For some reason, I can now only connect one laptop at a time to the networkWhen I try to connect, it says, "Windows was unable to connect to [network name]". When I try to connect with my Macbook, it says "network timed out". Before, I was able to connect all three without any problems.
View 4 Replies
View Related
