Netgear WNR2000 Router Behind Netopia 2241N Configuration
May 25, 2012
Our ISP provided a DSL modem/router (Netopia) that I connected to the Netgear wireless router with dd-wrt flashed. All I've done so far is connected the two. I have a connection, but I want to know if it's possible or advisable to configure everything from the Netgear router. But following the instructions here[URL], it seems I have to configure DNS and such using the Netopia router. I don't have a full grasp on how to use them together the correct way - like using the Netopia as an ethernet bridge.
View 4 Replies
ADVERTISEMENT
Jun 29, 2012
I'm trying to use a Netgear WNR2000 router as a repeater, I have a Netgear WGR614v9 as the main router in my house. I have followed online guides as closely as possible but am still having troubles. My main router is working fine, everything can connect to it and gain access to internet despite having to change the security to WEP to allow for the repeater function to work. Now I am having troubles getting the repeater (WNR2000) to connect to my main router. The ip address of the repeater is listed in the connected devices of the main router and everything is managing to 'find' the repeater just fine but when I connect and put in the WEP key there is no internet connection. I read that a static ip address is needed or something like that but I am completely baffled
View 1 Replies
View Related
Jul 22, 2011
ok I have logged in my router & clicked the repeater mode. whats the next step. BTW I am a complete newby to networking.
View 4 Replies
View Related
Jul 4, 2011
I have a similar problem to thread with same name dated 31-Jul-2010-that is now closed. I'm using Qwest internet with Actiontec PK5000, and I have to use my Netgear WNR2000v3 as a repeater.The Netgear is working as a repeater however I can't get internet through the LAN connections on the repeater. After checking the settings over and over again I'm beginning to think the repeater will only work with wifi. I need to hook up my desktop in the office, DirectTV, and Blueray player LAN connections to my repeater.
View 1 Replies
View Related
May 23, 2012
Today a bought a brand new Netgear WNR2000 router.Upon setup the wifi was working correctly. All of the lights where active and it seemed everything was in order.Because the power cord was in the way I moved it and plugged it into a different powerpoint. From then onwards my router has not been working. Only three of seven lights are active (green).
I have tried unplugging and replugging all network cords. I have also turned it on and back off, reset the router and run the initial installation program thrice.What should I do now? Nothing so far has effected it. The computer I am installing it on is running Windows XP and the laptop I intend to use the wifi on is Windows 7.
View 1 Replies
View Related
Sep 29, 2012
Here is my setup:
Netgear WNR2000 router.
Macbook Pro with Snow Leopard connected to router through wireless.
Windows 7 Desktop getting internet through the MBP ethernet.
I can't figure out how to be a part of my "Home Network" with my Win7 Machine so I can see other computers in my house, use my networked printers, etc. I can only see the MBP it is connected to in network panel. I want to be able to stream the movies on this computer to my iPad which is connected to the wireless router.
View 8 Replies
View Related
Dec 5, 2011
I replaced a Netgear router with a similar Netgear router, but the LAN is no longer working.The old Netgear router would drop internet, but LAN would work. Replaced it, the new Netgear router works fine with the internet (cable modem), but the LAN with two computers will not work. The desktop with Windows XP, and a laptop with Windows 7. After runing network setups on both computers several times, I have been unable to reestablish the LAN, however internet access via the router is working. Reinstalled the old router and the LAN works fine, allowing file and printer sharing. Old router is a Netgear WGR614v2, new router is a Netgear WNR2000how to reconfigure the router/computers to get the LAN working again with new router.
View 8 Replies
View Related
Jan 14, 2013
I just installed DD-WRT, version DD-WRT v24-sp2 (03/18/12) std, in a Netgear router model # WNR-2000V3 and so far everything is running good except for the LAN ports which are not working. I don't know what settings I have to change to get it working and I tried a lot of options from the DD-WRT site. I want this router to be an access point but it seems like I can't use the LAN ports at all whatsoever. Could it be that this firmware is no good? If so, is there a way to revert back to the factory NetGear firmware?
View 3 Replies
View Related
Jun 9, 2011
So here's the setup, my apartment is right next to my parents' house (don't ask why) and they have a netgear WNR2000 router in their upstairs loft connected to a modem going to a local internet provider. My apartment is just far away enough so that I can barely get a signal, so I'm trying to set up a second wireless router (netgear WNR1000v2) in my apartment that will connect to the internet through the first router so I can get a better signal. I do have a way of running an Ethernet cable from the first router to the second in my apartment.
View 3 Replies
View Related
Apr 27, 2012
Netgear wnr2000 download driver
View 1 Replies
View Related
Feb 6, 2011
ok so i finally got a decent dsl modem, from our isp it is also a wired/wireless router, i have Netgear WNR2000, that is conencted a lan port on the dsl router/modem, how do i set it up as an acces point so i can access the ip range of the dsl modem/router?
WNR's ip range : is the 192.168.1.x
Dsl modems's is: 10.0.0.x
I need to connect a computer which right now is at 192.168.1.x to my domain controller which is at 10.0.0.x..
View 9 Replies
View Related
Feb 17, 2011
I have a Motorola SBG901 router/gateway that is hooked to my desktop. I recently purchased a Netgear WNR2000 to use as a router to connect to a Blue-Ray player to receive firmware updates wirelessly. On every attempt to access the netgear unit to set it up as a repeater, I get nowhere. I tried hooking the unit up to my laptop and login in under the admin account but again to no avail. I really don't want to have to disconnect the SBG901.
View 9 Replies
View Related
Jun 1, 2011
How do I personalize the settings on my router from default. Netgear wnr2000.
View 2 Replies
View Related
Aug 9, 2011
I have two routers. One is Netgear WG602 v3 and Netgear WNR2000. WG602 v3 is connected with internet. I want to make a wireless bridge. How?
View 1 Replies
View Related
Aug 8, 2012
What is the default IP address for a Netopia 3347 router?
View 3 Replies
View Related
Aug 3, 2011
I currently have service with AT&T DSL. I have their Motorola Netopia 3347 modem that is set to Bridged mode and going to a Linksys WRT54GL router, which then goes out to a Cisco 24 port switch.AT&T has given us a Static IP to use, which was set up and working just fine when the modem was NOT in Bridged mode. Now that I have it set to bridge mode (as per a request by our VoIP provider), our IP address is no longer static at WhatismyIP.com...instead it changes frequently. However, I have a back up server here that needs to have a static IP so offsite back ups can find our modem/router and then the back up server.I am running Tomato software on the Linksys admin. When I go to the Basic->Network section, the WAN/Internet is set to PPPoE with the AT&T username and password that was originally used in the Netopia modem entered in. If I set this option to Static, it removes the username/password fields, so I do not think that my internet would work that way. Or, would the Netopia use the username/password to authenticate, and then just pass it through to the Linksys in bridge mode and THEN it would use the static IP? what I need to do to make the Linksys grab our Static IP instead of changing? Neither AT&T or the VoIP company can figure it out...
View 2 Replies
View Related
Sep 9, 2012
I am having trouble with my modem/router the netgear dgn2200 n300. I bought it to replace my older netgear modem/router (same model v2 to v3).The problem is I just keep getting disconnected say every hour or so when I am using the internet and sometimes it can disconnect me 2-3 times in half an hour. I have removed the filter/splitter and plugged the dsl cord from the netgear straight into the wall bypassing the filter and I still get disconnected.When I am online I receive great connectivity and I consider the bandwidth to be just fine for my needs.My question is what do I have to do in the settings of the router or in my internet properties for it to stop disconnecting me as it gets frustrating. I will take any advice except for "get a new router" or "do an isolation test" blah. Simply because 1. It happened with my old router and with my netcomm modem. 2. I have already done an isolation test and somethings not configured properly I think so, I am no networking wizard.
View 14 Replies
View Related
Feb 7, 2012
I have two routers set up. It goes from the modem through a WRT54G2 to a WNR2000. I have one pc connected to the WRT54G2 that gets 20Mbps and another connected to the WNR2000 thats only getting 5Mbps. I realized recently I have them connected to each other wrong. Or so I assume. I have the fourth port on the WRT54G2 connected to the internet port on the WNR2000 and it's set to "Automatic Configuration - DHCP" and "DHCP Server" is enabled. From what I read one or both of those is supposed to be set to manual.
View 2 Replies
View Related
Jul 11, 2011
I have a NETGEAR Wireless-N 150 Router WNR1000 v2. I am trying to configure it for my LAN which has a DIALER. [code] I tried to configure my NG but it is unable to connect to the network on its own. I have to use CONNECT dialer from my PC to connect which is useless because I can't use my wi-fi enabled devices to access network.
View 1 Replies
View Related
Dec 29, 2011
I am currently experiencing difficulties setting up a Netgear router (WNR834B). The router I had been using previously allowed me to access the internet, but frequently dropped the connection, especially when I connected to it via my laptop. I have the new router set up correctly (I even get a signal from it) but both the desktop computer I set it up through and my laptop cannot access the internet. When I diagnose the connection issue I get the message "The network adapter "Local Area Connection" does not have a valid IP configuration."
View 14 Replies
View Related
Apr 6, 2012
i've been tring to configure our netgear N600 router, it directs me to the support homepage all the time after we half through the configuration and got disconnected at first try. now i've tried clean dns, reset internet settings, nothing seems to work...
View 1 Replies
View Related
Apr 22, 2012
I have a Westell 6100 modem. After my old router, a DIR-655, got zapped by some electric charge from a nearby thunderstorm, I bought a Netgear WNDR3800 router. But I have not been able to get the Netgear router to connect to the Westell 6100 modem reliably [URL]
A friend had given me a Netopia 3347NWG router/modem some time ago but I had never attempted to use it. I was able to get into the web setup screens of the 3347NWG and, without attempting to connect the Netgear router to it, I was able to connect to the Internet via the setup screen. But every attempt to actually go to a web address would fail with a timeout, and efforts to ping always failed with a timeout. Yet the 3347NWG setup said I was connected.
Does anybody know how to setup the 3347NWG so it actually can connect to the Internet correctly so that I am able to surf to a web page or ping an address successfully ?
Does anybody know how to setup the 3347NWG in Bridge mode so that I can use it strictly as a ADSL modem and try to use it with my Netgear WNDR3800 router ?
If I can not use the 3347NWG with my Netgear router I had planned to send the Netgear router back for a replacement since it is not connecting relaibly to my Westell 6100 modem. But if I can get the 3347NWG to work as a modem and reliably connect my Netgear router to it, I will not have to send back the Netgear router for another one.
View 1 Replies
View Related
Jul 11, 2011
I installed 6 Q-see Cameras, pretty easy to install. The problem is running the port forwarding so I can view the cameras in the internet. I am running a Netopia 3347-02 router. I am not sure how to port forwarding so I can view the cameras over the internet. On the seeting for the DVR. I can see the Ip address ex. 198.168.X.X and the port is 80. On the Netopia 3347-02 router I went to pinholes cause is wher it will let me do the port forwarding, and I name the port Ex. test,
pinhole name ; TEST
start port: 80
end port: 80
[Code].....
View 1 Replies
View Related
Jan 24, 2011
I recently setup a Camera (DVR) system for a good friend of mine who just opened a restaurant. We are able to access the cameras just fine internally (LAN), but not externally (WAN).
I port forwarded, or 'pinholed' as this router uses, ports 9000 and 80 (changed the routers web port to 81 so there would be no conflict). I grabbed the external ip for the network and immediately tried connecting from home (I was doing everything remotely), and could not access the cameras, neither with the dvr software, nor with internet explorer.
EDIT: I believe he has a dsl line. I wonder if we'd need to change the configuration in the modem itself?
View 2 Replies
View Related
Feb 24, 2012
One of my housemates has had to borrow my wifi adapter to connectto cable BB in my house which uses a cisco epc2425 cable router/modem.Recently found a Netopia 2247. Is it possible to setup the 2247 asa wifi repeater so my housemate can simply connect to the 2247 via
View 1 Replies
View Related
Sep 2, 2012
I would like to change the default ip address on my netopia 3347 frrom 192.168.1.whatever to 192.168.0.whatever
View 2 Replies
View Related
Dec 13, 2012
I have a netopia 3347 with 5 useable statics from att. What is the best way to go wireless with this set up. I do not want DHCP turned on. And i would like to not assign an ip to the laptop.
View 1 Replies
View Related
Apr 23, 2012
I need viewing a DVR camera system remotely through a Motorola Netopia 3347 router. I was able to view the system properly for a year with the old ATT modem and a separate router, but recently the modem crashed and ATT replaced it with this Netopia that I can't for the life of me, understand.I can view locally but not remotely from the internet. I need establishing the Pinholes properly. I'm trying to get it working for port 85 for the DVR system. But I'm confused on the Internal vs. External port #'s it asks for in the Pinhole screen. No combination I enter seems to work. I even tried just using port 80 to get it working, but there was a conflict creating a pinhole for 80 since its already mapped to HTTP.
View 5 Replies
View Related
Sep 27, 2011
I have a netopia 3347W adsl modem/router that I have put in "ethernet bridge" mode. At that point the RV110W has to authenticate to ATT using PPPOE. I have verified the username/paswd for the PPPOE connection. The 110w will not complete the PPPOE connection. Looking at the logs it shows that it handshakes and authenticates with the PPPOE server. Then unexpectedly the log shows a termination with exit status 15. It then tries to renegotiate the PPPOE connection.
View 2 Replies
View Related
Apr 12, 2011
I bought the Netgear N300 WNR2000v2 today for my laptop (ACER Aspire 5552). Installation was fine but when in try to connect to the router i get a message "Windows was unable to connect to 'SSID Name'. However when i go into routerlogin.net and change the security options to 'None' i get connected to the internet no problem.
View 4 Replies
View Related
Oct 10, 2011
I have a NG PS121V2 print server that i had working on my cradle point MBR 900 with a lexmark E238 I lost the MBR 900 during a storm so i picked up a Belkin N300 until i decide what to do about ISP.I can not get the NG Print Server to now. when i go through the setup wizard for the Print server i can configure and print a test page but as soon as i exit the setup wizard i can no longer print? e)
View 1 Replies
View Related
Jan 5, 2012
how to configure a server with net gear switch . I want to restrict access for a few users and use the netgear switch for file sharing between the small network. its got auto configuration .
View 3 Replies
View Related
Dec 19, 2011
I have a Netgear wnr1000 v3 router. & At about 12:00pm central standard time. It kinda messed up.. This is the Problem.. I have seen this "Local Area Connection" Doesn't have a valid IP configuration. I've browsed and browsed and browsed.. Over and over trying every solution. It's gotten me so frustrated.. I don't want to return the router.. Nothing works for me.
View 2 Replies
View Related
