Cisco :: 3310 MSE Was No Longer Visible On Network
Feb 22, 2012
I performed a software reboot on the MSE3310. After the reboot the MSE was no longer visible on the network. I went and consoled into the device and it was operational. I ran the msed stop and msed start commands. I got this message when it tried to load eth0.Bringing up interface eth0: e1000 device eth0 does not seem to be present, delaying initialization.Earlier in the day I had updgraded the firmware from 6.0 to 7.0.230.0.
View 6 Replies
ADVERTISEMENT
Apr 9, 2013
Region : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
We are trying to use a TL-WR941ND purchased about a month ago, but it keeps hanging, usually within a day or so of operation.To be clear: by "hanging" I mean the device stops providing wireless services (its SSID is no longer visible in WiFi clients) and becomes nonresponsive to pings or control access attempts (via settings web page) from the internal network connections.The device is used in a very simple scenario, where it's being employed as a simple access point, not as a router. As such, the device's configuration is as follows:
* WAN interface is configured with a dummy static IP (10.10.10.10/24) with gateway and DNS set to the internal IP address of the actual routing device connected to the external world.
* LAN interface is configured with an IP address inside the actual internal IP subnet (192.168.1.0/24).
* DHCP is also disabled as this service is already provided.
* Wireless settings: radio enabled, SSID broadcast enabled, WDS disabled, 11bgn mixed mode, auto channel width, max TX rate, channel 7 (manually set). Using WPA-PSK security.
Rest of the settings are unchanged from their default values, as the device isn't being used as an IP router by any client - just as a WiFi/Ethernet layer 2 bridge. We're using what appears to be TP-Link's latest stock firmware for the device.The settings described above appear to provide the connectivity required by the WiFi clients. However, the device continuously hangs within a day or so of operation, requiring someone to physically attend to the device and cold-restarting it (disconnecting it from power and reconnecting it) to regain an operational state.
After performing a cold restart, the system log shows nothing beyond the startup entries: "System started" entry followed by security info entries regarding enabled protocols. Then the device appears to work well for a while, until it hangs again, forcing again someone to attend to the device, etc.
View 6 Replies
View Related
Apr 4, 2011
I am on network with administrative rights and one computer on network is not visible in ipscanner, cannot connect with remote desktop connection. Cant even connect by typing in run command (eg. \192.168.1.10c$) The computer is ON and users have logged on it many times. This same problem happens on many other computers too, and its not permanent. After few days or so, he problem is gone, and sometimes persists after a weekend, when pc is shutdown on Friday. Operating system is windows xp sp2 and there is no third party firewall on remote computers.
View 1 Replies
View Related
Jul 14, 2011
My PC is wireless connected to my modem, My X-Box is wired to my modem, PC detects x-box in home network, X-Box doesn't see PC when running connection test, X-Box however does connect to web. When I plug in an Ethernet Cable from my Modem to my PC the X-Box instantly detects my PC. I can't figure out how to make my x-box communicate with my PC when it's it's half wireless / half wired.
View 1 Replies
View Related
Oct 8, 2012
My home network, consists of a bunch of Win 7 computers and 2 XP machines. One XP machine is a netbook, it's rarely on and presents no issues.Here's the problem I'm having with the other XP machine:-My Win XP PC does not show up in the list of networked computers on any of the other machines on my home network.-But I can still access the shared folders by going to start and typing in \computer name.Win 7 will open a folder containing all the shared folders and I have no problem accessing (and modifying) any of its contents.-I also can access the PC via a VNC client set up on another machine and even have ports properly configured to access it from out of the house-I use this PC as a server to stream music to my iPhone via subsonic. No problem here either-I can access all the other computers from the XP machine in question.Since I can still get to the files this wouldn't be a big deal, except:-I can't map a network drive to the XP machine from the other PCs and I need to-I have an HTPC computer whose software can't find this XP machine because it's not there
View 1 Replies
View Related
Oct 9, 2012
Previously, I didn't have problems connecting to my office's wireless router as my laptop automatically connects to it when I turn the connection on. Then, for a few weeks, my computer could no longer connect to the said network. It really puzzles me on how this was the case when the laptops and other devices of my other colleagues can connect to the same network, so has my smartphone. When I was doing field work, I usually bring along my laptop and I found out that it had only a specific problem on my office's router since I can connect to other wireless networks. I searched over the net for any possible solutions; I rebooted the router countless times but to no avail. I made sure that I didn't get the encyrption key wrong all the time. I even tried to connect my computer directly to the router using a cable and tried to access the router interface via the web browser; but it couldn't connect. I then tried pinging it on cmd, and it only prompted a "time-out." [CODE]
View 6 Replies
View Related
Apr 26, 2011
At the company I work for, there are a few "network drives" to which employees are given access so that any mutual file stored thereon may be shared between and edited on demand. Not the best model, I know.Went to the server room a few minutes ago and found that "network drives," (P:), (L:) and (M:) seem to be invisible. Back at my workstation, I opened My Computer and saw all three on my screen.
View 3 Replies
View Related
Jan 8, 2013
In my new laptop with os windows 8 my 5Hz network is not visable.My 2.4Ghz network is the only one that is showing.
My Router is a Belkin N600DB
Hardware F9K1102 v1
Firmwareversie 1.00.19 (Jul 6 2012)
Versie opstartprocedure v0.07
View 1 Replies
View Related
Mar 26, 2013
I have TV set box connected to modem router supplied by ISP provider. To the same router I connected EA 4500 to which I wired connected Network Hard Disc at which I store music, photos and films, which I can not access via TV set box. If I connect Hard Disc direct to the modem router to which set box is connected, access works fine.
Whar shall I do to establish accesability of Network Hard Disc over all network ?
View 1 Replies
View Related
Feb 8, 2012
I have a Lenovo t42 with with Windows XP SP3.
The "Local area network connection" is not visible in Network Connections. The Ethernet controller and adapter driver is properly install (no yellow signs). All Network services are also running properly.
The network is working fine, and getting an IP address from DHCP but has to restart the DHCP service once after booting.
View 1 Replies
View Related
Apr 26, 2012
MSE can not boot.MSE show error log. [code] How to recovery MSE 3310,I find in documents not show method recovery. Any solution recovery MSE 3310
View 2 Replies
View Related
Oct 30, 2012
I have a Dell Optiplex running XP wired to a Netgear router. My laptop is a Dell Inspiron 1501 running Windows 7. When I got the new router everything programed easily and I could retrieve files from my desktop and print remotely. Sometimes I would have to "refresh" before the laptop would detect the desktop but now it will not detect the desktop or the printer. I suspect that a Microsoft Update did this but just guessing. I went back and deleted the updates that downloaded around the time that this stopped working. I have tried every thing that I can think of to get it back working but can not get it fixed.
View 2 Replies
View Related
Aug 11, 2012
I'm trying to see if I can fix my friend's NAS which apparently has some pretty important data on it that wasn't saved anywhere else. They actually had the Geeksquad look at it and they've come to the same conclusion I have so far, but I figured I would ask the internet before I gave the thing back to them and said Geeksquad was right.
Anyways, they have this 5 drive RAIDed NAS which apparently just stopped showing up on their network. I borrowed it from them to see if I could figure it out. It turns on just fine and my router assigns it an IP address, but the IP address just takes me to a blank LaCie dashboard screen. It's weird because it's clearly running it's web server because it's just a gray background with an empty white box and "(c) LaCie 2010" at the bottom. No content at all.
Additionally, I tried installing the LaCie Network Assistant on my home computer and it says it cannot find any network disks. I've tried the "wake up a device" where I enter the mac address, but that doesn't do anything.
All the lights are solid blue on the front and over all the drives so it doesn't appear a drive has failed or something. Even so, that wouldn't really explain the blank dashboard right?
View 1 Replies
View Related
Feb 24, 2013
I've got an MSE 3310 that came with four-post rails for rack mounting. These came without instructions and we are having a hard time figuring out exactly how they work. They say General Devices C-300-S-124-RC-MOD
View 4 Replies
View Related
Sep 16, 2007
do i still need ACS if i have the NAC appliance say 3310.
View 3 Replies
View Related
Jun 8, 2012
I recently configured CISCO 3310 box with MSE version 7.2. Services are up and running in the box, I could add the MSE to WCS and also able to track the location using WCS. However, I could not connect the third party software to MSE web services to get the location information there. When I hit the server url "https://<my mse>" I get list of possible services like:
Error 404 - Not Found.No service matched or handled this request.
Known services are:
http://my server:8880/hs/
http://my server:8880/mdp/
http://my server:8880/admin/
[code]....
I browsed through the documentation (CAS_71.pdf) and found a text saying:
Note Port 80 will be enabled on the MSE if the enable HTTP command was entered on MSE. Ports 8880 and 8843 will be closed on the MSE when the CA-issued certificates are installed on the MSE. I am running the test system so I do not really want to install CA signed certificate, so I used self signed certificate and restarted the server, but it did not work.
View 10 Replies
View Related
Dec 20, 2011
Yesterday I discovered the primary and secondary CAS were both in active state and reporting their fellow peer as dead (I did this using ./fostate.sh), causing authentication errors on the network. I had to stop the perfigo process on the primary one to restore service.
After closer investigation I have discovered that when I put my laptop on the same subnet as their eth2 interfaces (eth0, eth1 and serial are not used for heartbeat only eth2), I can ping the eth2 ip address for the primary device, but can't ping that of the secondary device. See configs and outputs below. I am also wondering why the secondary CAS shows its eth0 and eth1 interfaces as fake0 and fake1.
[root@CAS-SEC ~]# ifconfig eth2
eth2 Link encap:Ethernet HWaddr 00:1F:29:5D:1C:6C
inet addr:172.29.254.10 Bcast:172.29.254.11 Mask:255.255.255.252
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:11205 errors:0 dropped:0 overruns:0 frame:0
[code].....
View 2 Replies
View Related
Mar 12, 2012
I have been using my wireless (linksys) for years now and just recently my wifi network no longer shows up on any of my devices (laptop, phone, etc). I am able to hard wire into the linksys and my laptop works but when I try to connect wirelessly, I can't even see the wireless network, I am only able to see my neighbors.
View 2 Replies
View Related
Mar 11, 2012
I am getting a hard time in order to understand the real difference between the two types of context aware licenses for the MSE:
1 . AIR-CAS-1KC-K9 - Context Aware License For 1K Clients and Tags (RSSI based)
2. AIR-CAS-1KT-K9 - Context Aware License For 1K Tags(RSSI, Chokeponts and TDOA)
For a regular network without any devices with tags such as RFID, I understand I do not need to get the .2, only .1, even though the .1 also is shared with clients at 1K of each. Also, the .2 does not say clients, only tags and advanced features as TDOA. Going through the Q&A it does not clearly says the difference, when to use one or the other.
View 3 Replies
View Related
Jul 19, 2010
We'll be implementing Cisco NAC guest server for Guest Wireless users, ( Model #3310), the question is do we need to configure separate physical interface for User authentication requests( from Wireless ) and a separate Interface for Guest server to talk to AD for SSO?
View 2 Replies
View Related
Aug 27, 2012
The rouge access points being detected by the 5508 WLC are not showing up on the Context Aware tab of NCS? I have a MSE 3310 installed and configured and it shows to be syncronizing with the WLC. I'm sure I am missing some part of the configuration just not sure where.
View 3 Replies
View Related
Oct 24, 2011
I work next to someone who has been complaining constantly about how his computer will give him some kind of "Access is Denied" error on one of his network drives almost every time he uses it. Other network drives on the same server work. Because it can be fixed by rebooting, the IT person has filed it as low priority / given up on fixing it but I would really like to shut him up but I can't find the answer in google. His computer is Windows 2000 SP4 and the server is Windows NT 4.0.
Edit: It happened again and I was able to get the actual error message. "H:DIST is not accessible The specified network name is no longer available"
View 7 Replies
View Related
Jul 18, 2010
I'm trying to configure the NAC Profiler with a 3310 CAS Collector. In the "Edit Collector" menú, it shows all the modules as "Running", except for the NetWatch module which shows a state "Invalid configuration file (missingInternalAddress)".
I configured the eth3 interface of the CAS as a monitor interface in the Profiler (see attached image), and I tested that the SPANed traffic actually reaches that interface from the access switch. I'm using software version 3.1.0_24 in both the Profiler and the Collector.
View 2 Replies
View Related
Jul 20, 2011
How to solve this error in between windows 7(Host) & Windows server 2003(Guest).
View 2 Replies
View Related
May 11, 2011
I am trying to upgrade an MSE from version 6 to 7.0.201.204. I am able to copy across all the files and have tried using WCS and FTP for the CISCO-MSE-L-K9-7-0-201-0-64bit.bin file but the installation procedure always fails.
I will download all the images again tonight. Is there a way to delete the images from the /opt/installers/ directory?
Also the upgrade procedure in the 7.0.201.204 is pretty bad, there is no detail in any of the steps.
Here is output from the upgrade -
[root@SDC-MSE-01 installers]# dirCISCO-MSE-L-K9-7-0-201-0-64bit.bin database_installer_part3_4.zipdatabase_installer_part1_4.zip database_installer_part4_4.zipdatabase_installer_part2_4.zip
[Code].....
View 6 Replies
View Related
Aug 19, 2012
There are 2 locations to choose from. One location requires me to run longer CAT6 cables. 7 of them. The other location requires me to run a longer RG6 cable. (the CAT6 runs would then be about the shortest they could get)So, I guess I need to know which can handle running parallel with power cables better, 25feet of RG6 or CAT6?The parallel with power cable is only for about 6-8 feet, but that's already more than it should be for CAT6.
View 4 Replies
View Related
Oct 9, 2012
I have a 3COM 3CRUS2475 24 Port PoE Switcher that I connect a number of Crestron control units to.All of a sudden yesterday I could no longer see the network on any device including Ipads, Laptops etc.I have rebooted several times and restarted all of the access points around the house but still cannot see the network. I have also connected a WAP directly to the Switch with a new LAN and still nothing.
View 1 Replies
View Related
Sep 27, 2012
My laptop all of a sudden can't connect to my wireless internet connection and also seem unable to find any other wireless network but mine.I recently moved to a new flat, but brought my old modem/router with me (Scientific Atlanta 2434) and use the same ISP. Last week everything worked as a charm, but at the new location my laptop won't connect to my network, though I can connect to it through my mobile phone. My laptop only seem to find my own network ("Fidel") but with my mobile I can pick up 10-15 different networks from my flat. Connecting my laptop to the modem with a cable works all good. I tried to remove "Fidel" from my networks and added it again, typing wrong password gives a message saying "wrong network key" so my laptop and the modem seem to shake hands at least. Yesterday when trying I actually got connected, but the connection died after a few minutes and I wasn't able to connect again.Windows device manager display no errors nor conflicts around the ethernet controller or network adapter. Have tried to update the drivers through the device manager as well but it says they are up to date.Windows version is Windows 7 Home Premium.Don't know if my ISP uploaded new firmware to my modem when I connected it in my new flat, but on the other hand I can't see why this would affect my laptop's ability to pick up other networks in my house? [code]
View 4 Replies
View Related
Feb 28, 2012
I have Dell machine with Win Xp3 loaded, on my local network (and other computers). I set NIC card "Link Speed & Duplex" to autosense & make direct connection to my modem and works ok.When I plug into the network router I get the 'Cable is unplugged' and no Internet connection.I can change the "Link Speed & Duplex" to 10Mbps/Full Duplex and get intermitten connection. Also when I copy a file from Mapped drive I get "Cannot copy xxx - The specified network name is no longer available".
1. the NIC software is recently updated PRO/100 Adapter NDIS 5.1 driver
2. Although Microsoft has suggested Symantec < ver 4 has had an endpoint problem, I have 10.1.6.6000.
3. TCP/IP Properties are on automatic like the other computers.
View 3 Replies
View Related
Jan 19, 2012
I can no longer add user permissions to a network C: drive - I get an access denied message. What could have happened?
View 6 Replies
View Related
Jun 16, 2012
The other day while I was browsing the internet all of a sudden my internet stopped working. I look down below and try to connect to the network again but it no longer shows my network anymore. I went into the room of my router and it looked fine. All lights were lit up like they should be. I turned on my Laptop to see if it was just a problem with my desktop but it's still not showing my network either.
I have restarted my router and reset it numerous times and it has still yet to show my network. It only seems to work if I connect it to my Laptop with an Ethernet cord. I have two different routers (Both Linksys) and they both do not work.I also have two different wireless adapters (D-Link & Netgear) and they both do not work
View 14 Replies
View Related
Nov 24, 2012
I have a Dell laptop running Windows 7. The problem is that every single time I try to connect to any wireless network, I get a message that says "Connecting to the network is taking longer than usual."The network almost always connects eventually (about 2 minutes), and once connected there doesn't seem to be any other problem.This has been going on for about 2.5 months. It began shortly after I restored the laptop to factory default.
View 11 Replies
View Related
Jun 16, 2012
I have a LAN with about 200 computers (192.168.10.0/24) with a DHCP Server on Windows server 2003.The problem is that my company have acquired 100 others computers that I have connected on this network.Some computer does not get IP address from the DHCP server. When I investigated the log of the DHCP server, I realized that the DHCP server was out of addresses.
View 2 Replies
View Related
