Cisco AAA/Identity/Nac :: Changing Timezone In ISE 1.1.2?
Apr 16, 2013
I need to change the timezone of two ISE 1.1.2 servers. One primary and one secondary. Both are set to "EST" timezone and i would like to change them to AMERICA/Montreal because they are now one hour late since day light saving change.
According to the release notes, it is not recommended to change the timezone on ISE after the installation. I'm thinking of doing a backup of the ISE application (in the maintenance GUI or CLI) and then changing the timezone on both servers. After the change the ISE servers will gain one hour. So after i will do a restore of the backup i did just before the timezone change. The timestamp of the backups will be older then the current time of the servers.
Will this work? Is it the best way to change the timezone?
View 3 Replies
ADVERTISEMENT
Apr 6, 2013
I need to change the IP address of existing primary cisco ACS 4.2 (windows based). What is the required procedure to change the IP address?
View 4 Replies
View Related
Oct 11, 2011
I use ACS appliance 1120 for cisco devices administration. The identity store is external. I use Active directory. Actually, Authentication, authorization and accounting work well but users can not change theirs Active directory password when they have expired. Do you now how to configure ACS to permit password changing?
View 5 Replies
View Related
Jun 13, 2012
I am trying to move a device from the Default location to a sub group and get the following message when I try (either with IE or Firefox)
This System Failure occurred: Index : 0, Size: 0. Your changes have not been saved. Click OK to return to the list page.
it also gives me the same error if I try and change the Device type from default to a sub group. I'm sure I could do this previously. The ACS build is (VMWARE install):
Cisco Application Deployment Engine OS Release: 1.2ADE-OS Build Version: 1.2.0.228ADE-OS System Architecture: i386
Copyright (c) 2005-2009 by Cisco Systems, Inc.All rights reserved.Hostname: ACS1
Version information of installed applications---------------------------------------------
Cisco ACS VERSION INFORMATION-----------------------------Version : 5.3.0.40Internal Build ID : B.839
I'm suspecting it a read/write issue with the database or a database corruption. I have stopped and started the application acs via the console and show application status acs has the following to say about itself.
ACS1/admin# show application status acs
ACS role: PRIMARY
Process 'database' runningProcess 'management' runningProcess 'runtime' runningProcess 'view-database' runningProcess 'view-jobmanager' runningProcess 'view-alertmanager' runningProcess 'view-collector' runningProcess 'view-logprocessor' running
View 3 Replies
View Related
Mar 10, 2011
My exchange server should have an outside interface ending in .82 which is one of public IP's assigned to it.Inside 192.168.168.250 -> Outside x.x.x.82 How can I configure this in ASA 8.4(1)?
View 3 Replies
View Related
Jul 29, 2011
I've finally gotten tired of Netzero Dialup and want to change to dsl from U Verse. That brings up some questions. Do I cancel Netzero when I start U Verse or do I need Netzero to make it work? If I have to cancel Netzero can I transfer my favorites over to dsl? How difficult is it to set up dsl? Does the box come by UPS of Fed Ex?
View 6 Replies
View Related
Apr 23, 2011
I tried changing the WEP to WPA because I recently found out our neighbors were stealing internet from us. However after doing all this changing around I used 192.168... And all that and was able to change the ssid and the passphrase but after doing so the Internet stopped working. We are able to connect but it says there's no service or limited connectivity so no web pages or anything loads. Now I can't get back to the router page by typing that 192.168. stuff because there's no Internet. Don't know what to do. This is my fathers ISP and it's not the greatest considering the location. I've tried unplugging the router and whatnot but that's not working either. I think we need to get back on the router page and fix something but it's not allowing us to since there's no Internet. Am I going to have to change back to a WEP.. I dont really want too. The router may need to be upgraded too because it's pretty ancient.
View 4 Replies
View Related
Feb 7, 2012
A router restart. I changed the wpa to wen so I could connect my ds to wifi.So far what I have done was restart the modem, it's a Cisco wag120n. This is a wireless so the moment I changed to wen, I lost connection. I then used a cable to connect to the modem and managed to change the settings in the router page 192.168.1.1 back to wpa but with no success connecting to the Internet. I then tried ressetting the modem and computer with no luck. I cut the power to the modem router and turned off computer for 5 minutes. I then turned the modem back til it was stable and then the computer, again with no luck. I then factory reset via the button manually and via the modem page but both ended up with the unable to connect to primary DNS server.
View 6 Replies
View Related
Jul 19, 2011
how to change the ARP timer in CISCO. I know how to change th mac-address aging timer, but can't seem to find any documents on how to change the ARP timer from 4 hours.
View 2 Replies
View Related
Sep 28, 2012
I know know nothing about cisco devices. Just wanted to get that out there. I recently came to a job that has a 5505 setup as the network gateway, and as a vpn for employees to work from home via the Cisco VPN remote client program. We had one main server that was domain controller, dns, and dhcp. It was a old 03 box, and I setup a new 08 r2 box on a different IP, and migrated all the above functions to it. Old server was a xxx.xxx.xxx.31, new server xxx.xxx.xxx.6. I found the java ASDM program(6.1) and connected to the ASA, and I have changed .31 to .6 in as many places as I can find, however, vpn clients on the outside can no longer connect to their desktops, as when i open a command prompt on their computer, the only IP they can ping is xxx.xxx.xxx.31, pinging xxx.xxx.xxx.6, or any other address fails. I'm guessing maybe it's in the firewall of the asa, but have no ideal really. Was there anything else I was suppose to do? Someplace I overlooked?
View 7 Replies
View Related
Aug 31, 2011
I am currently running WLC - 2100 with software version : 7.0.98.0
My question is :
How to change the existing password ( not reset ) but change the password with the web interface ?
If that cant be done, then my guess is I have to do it via telnet/ssh session
View 4 Replies
View Related
Oct 23, 2012
I have route-map defined on my ASR 1002 12.2(33)XNE and applied to my gi0/0/1 interface. I need to change the IP address defined on the "set ip next-hop ..." line. My question is, when I make the change in just the route-map definition, does the change take effect immediately, or do I need to remove and re-apply the "ip policy route-map ..." statement on the interface? If I do have to remove and re-apply, will this be service-affecting for all the traffic flowing through the interface? I'm just not sure what to expect.
View 2 Replies
View Related
Jun 10, 2013
I have a few site-to-site VPNs connecting to my ASA 5520, but one of the remote VPNs is changing it's public IP, how can I change this IP on the ASA without starting again? On the ADSM it is greyed out so I can't edit it, but can I just change it in the CLI?
View 2 Replies
View Related
May 5, 2011
I want to configure an access RNIS with a router Cisco 1603.When I plug a cable in interface ISDN BRI with the command "ALL DEBUG EVENTS" start, I have this message : "BRI0 : changing state to F5", and after nothing. How the interface BRI 0 can arrive to State F7?
View 2 Replies
View Related
Nov 13, 2011
Running lms 3.2.1 CS 3.3.1 on Windows 2003
I need to point the LMS server to a new mail relay, but when I make the change in
CS->SERVER->Admin->System Preferences smtp server
It claims to have made the change successfully but the old IP address remains.
View 3 Replies
View Related
Aug 28, 2011
A client was having some email issue and was requested to change the 1841's LAN and WAN interface MTU to 1400 bytes. i've used 'mtu' command but was rejected and got an error like to one attached. so i used 'ip mtu' instead to make the change.
What's the difference between the 2 commands and if this would achieve the said change. I've checked using the show interface it's still showing MTU of 1500 bytes.
View 6 Replies
View Related
Jun 20, 2011
I need to edit device information for multiple devices using feature Edit Credentials. I'm not able to overwrite all device credentials using a new set.
View 2 Replies
View Related
Mar 30, 2011
I'm having troubles with a cisco 877 router, it keeps changing itself to either 0x2101 which is good, or to 0x3100 which is bad because it messes up my bautrate to 1200 instead of 9600.it doesn't seem to matter if I change it, it will still tell me that it will change at next reload. [code]
I have never seen this before.the command in conf t : configuration-register 0x2101 is not working, played with wr mem or copy start run neither of one useful.
View 5 Replies
View Related
Nov 15, 2011
We are upgrading our dsl to cable. We have a cisco 877 router/dsl modem and windows sbs 2003 r2. May I know how do I change the ip addresses in the router, and how do I add a cable modem to the router?
View 1 Replies
View Related
Mar 22, 2012
Recently I installed LMS 4.1 accidentally on the c-drive, which, as a result, fills itself with a growing database and associated logfiles. How can I move both items to another drive safely? I allready managed to move configs and downloaded software.
View 7 Replies
View Related
Dec 11, 2012
I have been trawling the interenet looking for an answer to the i but to no avail.Can you change the source port that windows uses when it makes a connection to another host.
[code]...
View 7 Replies
View Related
Jan 13, 2012
I had to assigne my PC a new static IP address and now other computers cannot access the shared printer attached to this PC . It still show up in the printer pane of the other computers but you cannot print to it. The local PC attached to it via USB will printer fine.
View 4 Replies
View Related
Oct 10, 2012
Back in may, I built my own gaming rig and have been using wireless on it all the time. But recently my speeds has been going down, and i can't be bothered to fix it. That's why i wanted to use ethernet on it. My problem is that there is only one port on my modem for Internet, and that is being used by a routher that goes upstairs.
As you can see, i have three TV ports and one PC port. All of it is being used.One of the TV ports goes trough the wall too a exit in my wall, and goes into my TV Router as seen on the image below.
View 1 Replies
View Related
Aug 29, 2012
Everyday a few of the computer will error with "A duplicate name exists on the network:" A quick Google search shows the same answer EVERYWHERE on the internet. So I changed the names of a few of the computers too something I knew was unique. Still though the problem persists/ it afters the two XP bases computers the most, but my main workstations (windows 7 sp1) has had this error a few times, although it appears to have left for a while. I have a feenas server but Active directory is not turned on.My router is a e4200. I was using DHCP server on there (and would very much still like to) although I have turning it off, rebooted both the router and the computers but to no avail.
View 19 Replies
View Related
Jun 15, 2011
Every so often (random amounts of time) my internet setting either on the router or pc change and then I it comes up with an error that my settings aren't the same as my router... I use a Orange Live box and windows 7. also when I want to sign into games for windows that sometime crashes the internet and on DOW2 and minecraft.
View 10 Replies
View Related
Feb 12, 2011
I tried changing my ip address using ipconfig / release. I tried to fix what I did using ipconfig /renew but it tells me no operations can be performed on local connection 5 while it's media is connected.
View 12 Replies
View Related
Mar 14, 2012
i am willing to know that how we will refresh our WAN IP's dynamically.
View 3 Replies
View Related
Nov 4, 2011
How do I change my security key on my laptop?
View 1 Replies
View Related
Sep 2, 2012
I play this hockey.tk game. I want to change my ip to a different nearby state. For example, If I live in new jersey i'd want to change my ip to New York so I can play the game. How do I change my ip to that? For some reason I got ip blocked on a game.. So I was wondering if there was any way to do that
View 3 Replies
View Related
Apr 9, 2012
I am trying to configure a router with a satellite connection. I am following a HughesNet guidline. At step four after typing in the required IP address , nothing happens.There is no place to type user name and password.
View 2 Replies
View Related
Sep 21, 2011
How to change ip address in windows 7?
View 1 Replies
View Related
Jan 29, 2011
How to change the security key. How does one go bout that? Did not see that within the manual for some strange reason.
View 1 Replies
View Related
Jun 1, 2013
I am having two 6509E working in VSS and both are working fine. But the configuration register of command "remote command switch show boot" is 0x8000 which is different from that of RP (0x2102) .Now i want to change the value of configuration regsiter of SP to 0x2102.
View 1 Replies
View Related
