I just received a new SR520-FE router and am having a hard time getting it configured right. AS of now it is in my lab in a simulated "customer environment". I can ping what's behind it, what's in front of it. But I can't get outside access. I know it's probably something small so I am hoping another pair of eyes might be able to see what I don't. Here is the running-config. It's the factory setup minimally adjusted.
SR520 Base Config - MFG 1.0
User Access Verification
Username: ciscoPassword: SR520#show runBuilding configuration...
Current configuration : 6177 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname SR520!boot-start-markerboot-end-marker!logging message-counter syslogenable secret 5 $1$m/V3$CM6/dHniD1KgHsPZV6jV70!no aaa new-model!crypto pki trustpoint TP-self-signed-
My operations manager says "Could you go on-site and configure a new clients new internet connection?" I make the arrangements and go on-site. As I'm working with the providers tech he says "Do you have a sub-interface confgured for a dot1q VLAN id of 1057?", I say "What?". Anyway my firewall is not capable of dot1q VLAN, so he says "Do you have a Cisco router that can provide the trunking?", I say "Yes, I tink so but not with me". The question is can I use an SR520 between my firewall and the provider demarc to route the VLAN he is talking about? My initial discovery says yes but I am not quite sure of the details on how to achieve this on the SR520.
I got myself lately Cisco SR520 router with some basic firewall functions built in. This is going to be used for my home broadband, so no need to be really super secure, as it would be for some business. I managed to configure it, however there are few things on the firewall side, which I don't understand.
This router had some default configuration in it's flash, when I bought it. There are class maps.... how it works or how to add/edit rules. Also, do I need to use class maps, or can they be replaced by ACL's to certain extend? How to add/edit class maps rules to allow certain port (eg. 3333). Pease see below part of the default config:
class-map type inspect match-any SDM-Voice-permit match protocol sip class-map type inspect match-any sdm-cls-icmp-access match protocol icmp match protocol tcp [Code]...
I'm trying to configure a zone-based firewall on an SR520 and am confused about the 'not' criterion. The 'zone-design-guide' says (my stress): Class- maps define the traffic that the firewall selects for policy application. Layer 4 class-maps sort the traffic based on these criteria listed here. These criteria are specified using the match.where my intention is to let only LAN hosts with IPs in the range 192.168.1.1 to 192.168.1.7 out through the firewall. There may be an easier way of doing this which I'd be pleased to hear about. But, even if there is, I'd also be interested to know what I'm doing wrong in the above.
I am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.
Internet ISP -> Juniper SRX 210 Ge-0/0/0 Juniper fe0/0/2 -> Cisco ASA 5505 Cisco ASA 5505 - >Inernal LAN switch.
1. Internet is connected to Juniper Ge0/0/0 via /30 IP.
2. Juniper fe0/0/2 port is configured as inet port and configured the Internal public LAN pool provided by the ISP. And this port is directly connected to Cisco ASA 5505 E0/0. Its a /28 pool IP address. This interface is configured as outside and security level set to 0.
From Juniper SRX, am able to ping public Internet IPs (8.8.8.8).
Issue:
1. From ASA am unable to ping public ip configured on Juniper G0/0/0 port.(/30) 2. From ASA no other Public internet IP is pinging.
Troubleshooting Done so far.
1, Configured icmp inspection on ASA. 2. Used the packet tracer in ASA, it shows the packet is flowing outside without a drop. 3. Allowed all services in untrust zone in bound traffic in Juniper SRX. 4. Viewed the logs when I was trying the ping 8.8.8.8 in ASA. It says "Tear down ICMP connection for faddrr **** gaddr **
I have 2 modules of FWSM in 6500 switch (failover).I need 5 context.When I use in routed mode (like in the picture) , I cannot ping the servers behind the firewall. (I have ping to FW context),In transparent mode, it is not happening.what is the problem with routed mode?
We are going to impliment Spectrum (CA) in my network,i have ASA-5580-20 firewall now my spectrum server want to communicate with firewall,then only it will discover the firewall logs.Now the problem is my spectrum server is in MZ zone(10.10.10.45) security leval is 70 and my inside interface(10.20.20.101) security leval is 100.
I am unable to ping from spectrum server to firewall because of high security leval.How can i solve this problem,can i change my inside security leval to 69 then i think it will ping.
I'm trying to get several VPN tunnels up. It seems that only 1 map can be assigned to the WAN interface (fa4). Is this true or is there an 'extended' map like ACLs?
I an aware the SR520 is no longer made, But we use the VPN Remote aspect of it (For site to site UC540 installs), is there anything else that has the same VPN functionality, and what would i be looking for in regards to terms for the client to be on the router itself?
Having problems configuring an SR520 to support SSL VPN with Active Directory authentication. I set up the domain and a user in the SR520. and get the login prompt remotely but when attempting to login using the active directory account i get a login error. I can login fine using local authentication.
I have a SR520 where WAN configured as PPPoE with Dyndns address. I have done all the configuration through the CCA, so far everything is working fine. But now i want to configure SSL VPN, but I have getting an error message : SSL VPN cannot be configured, please configure wan interface using a static IP address. Is there any way that I can configure the ssl vpn through a dyndns address?
I am having an issue get an EZVPN working between a 2811 server and a SR520 client. The symptoms are the SR520 makes multiple connection attempts to the 2811. It appears that sometimes these connections are successful and the SR520 is assigned an IP address but then the tunnel will be dropped and a new session will be started. I've attached scrubed configs for both the 2811 and the SR520. One other note, when connecting to the 2811 with a software VPN client, there are no problems, so I think the problem is with the SR520. On the other hand, the SR520 wasn't having any problems until we switched our VPN server from a UC520 to the 2811.
I have cisco sr520 adsl router i have everything set up and it is ok. Internet work but i can not open some web pages In DNS is not problem NAT work fine. When i try some simple adsl gateway the problem websites work correctly. I think the problem is on sr520 router.
I am trying to set up a static VTI IPsec VPN between a SR520 and a RV110w. This works fine between the 520 and an 861, but the RV110 complains about the "permit ip any any" default policy of the VTI. (Same thing happens with the 861 and rv110) How to put a policy in place that would be used in negotiating the tunnel that the 110 would accept?
Attached the lines out of the 110's log and the VTI setup.
I´m trying to configure SR520 Cisco router as PPPoE server. The point is, when configuration is done and PPPoE client is directly connected to the interface, SR520 doesn´t respond to incoming PADI. PADI is not shown in PPPoE debugs (debug pppoe events, packets and errors).On the other hand, I get the PADI capturing packets with wireshark (so PADI is being sent) and the same configuration on other router works fine.
I am having a tough time getting my VPN client to reach any devices on my office network. I have a Cisco SR520 configured with IPSec to terminate Cisco VPN client sessions. The client is able to connect successfully. I get a username/password challenge, and then I get assigned a pool IP address on the client computer. So the VPN connection looks good at that point but I cannot reach any devices in the office network.
Config below:
Building configuration... Current configuration : 8066 bytes ! ! Last configuration change at 06:14:35 PDT Wed Apr 13 2011 by admin ! NVRAM config last updated at 06:17:11 PDT Wed Apr 13 2011 by admin ! version 12.4
i have a demroom set up which includes a sr520 as the edge router connecting to the ISP and i have a uc 560 connected to that which is working fine i also have a new business edition 3000 and a 800 series router which im looking to connect to the sr 520 for access to the ISP as the 800 series doesn't have a ADSL line on it .i have given the 800 series routers wan interface a static address of 192.168.75.14 wich is from the address range in the sr520s default vlan and excluded the address from the DHCP pool. now from the ccp express on the 800 s i can ping the wan port of the 800 s and the default vlan/gateway of the sr520 and the wan ip of the sr520 but no further also once i try pinging it from the cmd on windows i cant ping any further that the wan interface on the 800 s .
I'd like just notify the missing "no ip name-server" command in sr520 series router. However is possible to enter the command "ip name-server" the only way to delete it is to copy a modified config from tftp or other source to the startup config. This behavior is normal?
setting up a link between a Head Office UC540 and a remote SR520 which I want to use a PC and an IP Phone from. This remote site is the first of several.I've found several examples of site to site IPsec VPNs, but none with references to voice and data VLANs, do I need to worry about this or will the phone just work.
I've created an IPSEC VPN site-to-site from a SR520 (remote office) to a Nortel Contivity(home office)...all works really well on the VPN front as I can communicate effectively over the tunnel. However, this setup will be deployed at a few smaller sites and I'd like to setup a split tunnel so that Internet bound traffic goes straight to the Internet while traffic bound for our home office goes over the IPSEC Tunnel.
I'd like to configure a VPN with two SR520. the first router is a SR520-FE-K9 and it's at office, the second router is a SR520-ADSL-K9 and it's at home.
Each router have a static IP and individually works well. I tried to configure, by CCA, the office router as a server and the home router as a client: at home I can't see the office network and I can't navigate.
Need step by step, using CCA to configure a secure VPN.
I have a SR520 just deployed at a remote site with Internet Access.
Working Environment: Remote sites have SR520 with IPSEC VPN back to HQ and netflow v.5 works through the VPN back to our PRTG server.
Non-Working: I cannot get Netflow data to our PRTG with this first SR520 implemented with Zone Base Security. I am not able to get my netflow traffic out. VPN is up and running. Internet is a dialer0 interface. I have a Kron job that does the copy run to tftp backup daily to the same PRTG server and it works fine.
Both my source interface and address on the TFTP command and the netflow commands are the same interfaces (VLAN75) and IP. The Destination ip is the same too (through the VPN tunnel).
I have installed an SR520 with wireless for a client. They have asked if there is an easy way for them to monitor who is connected to the wireless at any given point in time. They are not capable of using the IOS command line.
I'm trying to combine dynamic and static NAT on a SR520. My dynamic NAT is specified with:ip nat inside source list 1 interface Dialer0 overload access-list 1 permit 192.168.0.0 0.0.7.255 In addition to this I want to perform static NAT for a couple of selected internal hosts. I can do this:ip nat inside source static 192.168.1.5 10.85.10.2 which works fine but means that the source address 192.168.1.5 is translated to 10.85.10.2 for all destination IPs. What I want is for the above static translation only to occur for a particular destination subnet.To accomplish this I have tried:
ip nat inside source static 192.168.1.5 10.85.10.2 route-map toOtherSite route-map toOtherSite permit 10 match ip address 150 access-list 150 permit ip 192.168.1.0 0.0.0.255 192.168.10.0 0.0.0.255
But this does not appear to work. Instead it seems to render the host 192.168.1.5 unable to progress through the NAT, whether the destination subnet is 192.168.10.0/24 or not, and I can't work out what I'm doing wrong.
we have cisco sr520 adsl router at one of the sites. A device is connected to the LAN and needs to be communicated directly to the server with 3rd party over internet. we have a static public IP( a.b.c.d) for cisco router and want this IP redirected to the LAN IP address(192.168.1.20) of the device but locked to only 2 inbound IP address (eg.-1.2.3.4 , 5.6.7.8) .
I have a SR520W-ADSL-K9, I´m trying to setup it trough CCA, but I have some troubles. At the internet connection I mark PPoE option, enter the vci=0, vpi=35, the username, the password (like the ISP TELMEX suggest), and mark the IP Negotiated option, but I have not find the ISP service give me an IP Address and establish the connection.
I'am a bit newbie at using Cisco products and here is my problem : I have set up a VPN tunnel between 2 Sites (A and B) a few month ago using 2 cisco SR520-ADSL-K9. All was working fine until power failures occured on the sites B (secondary site).
What happened was that none of the ethernet ports were working, excepting during booting, I was then able to ping computers linked to ports Fastethernet0, FastEthernet1, FastEthernet2 and FastEthernet3 but after a few seconds all ports were disabled but my DSL seemed to be working.
So I took back the router home to check it. I managed (I think) to make a factory reset using a serial terminal and following the procedure described here [URL]
Since I did the reset, I thought I would be able to re-use Cisco Configuration Assistant (3.1) to re-configure the router (I am very bad at using the command lines) but I am unable to connect to the router using the supposed default IP : 92.168.75.1 (I set my computer to use 192.168.75.50 IP adress with mask 255.255.255.0). But I can't connect to the router ... even if the Ethernet ports seem to work because green light is on when plugging my cable. connect to my router using CCA ?
For more information, here is what I get when I run "show startup-config" and "show running-config" in terminal console. I guess the objective is to make the startup-config beeing the running-config, but I have no idea on how to do that ..
show startup-config show running-config Router#show startup-config
