I have cisco sr520 adsl router i have everything set up and it is ok. Internet work but i can not open some web pages In DNS is not problem NAT work fine. When i try some simple adsl gateway the problem websites work correctly. I think the problem is on sr520 router.
View 5 RepliesI upgraded my fireware and now the router don't do anything, I can't even login into it using [URL] which a hard wired connection. How do I get logged into the router to try and put the old version of firmware back on it?
View 4 Replies View RelatedMy SRP526W (running the actual firmware 1.01.27) didn't recognize my new Huawei E372 USB dongle (it's a T-Mobile web'n'walk Stick Business II, already installed the newest firmware 11.203.03.10.55).Using a Huawei E172 or a Huawei E353, both USB dongles works well. But they are slow compared to the E372. I'd really like to use the E372 stick because it's super fast with up to 42Mbps download speed.As I could read in the release notes of the SRP526W, the Huawei E372 should be supported since firmware version 1.01.26.Inside the Huawei E372 you can find the printing "Model: E372u-5", maybe this is a different model which is currently not supported by the SRP526W.
View 0 Replies View RelatedI want to make a question about RV042. I used RV042 router in my office. I used content filter feature in router.Althought this have not been apply the rules. I think I made wrong rules.I enabled the block enable forbbiden domain .And then added the websites that I want block.However, these websites are still browsing in local computer.
View 4 Replies View RelatedI have configured the sr520 using cca.Basically I have a device connected to the sr 520 via wireless with the ip address 192.168.200.160.
The SR connects to the internet using adsl and pppoe.I configured NAT to the device for a number of ports, however it doesnt work.
I restarted my pix firewall cisco pix 515 and when i start it again the Act lamp and the firewall didn't work .
View 1 Replies View Relatedcd doesn`t work and can access web for set up
View 1 Replies View RelatedI had the website filter ON and it was working very well to block a few websites on a schedule. And after a few month, it doesn't work any more. While it is possible that I scewed up the setting , I have tried so many settings.
So:DIR655 fw 1.32NA,hw A3,"Enable access control" is on with the desktop MAC address (used copy this MAC)(I have also tried my laptop MAC),web site filter is set to "deny",the router time is set using NTP dlink server,
I would like to set up a monitoring/site blocking system where I work (owners request) to black sites like Facebook, YouTube, etc. Are there any decent, basic freeware ones out there?
View 1 Replies View RelatedI have recently purchased six quantities of DIR-655 for my home use. When I registered them these six product, at the end of each registration, I got the message that I will get an email confirming the registration.I didn't get any email. I have checked my email span box and filter too.
View 6 Replies View RelatedProblem Host A unable to reach Host B, trace route from Host A it reach to Router B but the packet unable reach to the Host B here the 1st level troubleshoot I did
1. Traceroute and ping success from router A to host B
2. Ping success from router B to host B success
I wonder the packet reach to router B but it didnt pass to Host B.
I am switching out routers. I have some ports forwarded that I know I need to copy down so I can open them up on the new one, but besides that, what else do I need to do/know before replacing the old for the new?Currently, we have a TRENDnet TEW-431BRP. We are replacing it with a Netgear WNR1000.Is the new one good? I didn't set up our home network. Someone from my dads previous business and friend did it for us. So I don't know what exactly was done in the router settings to set everything up.
I figured just copy the ports that needed to be opened in the new router and maybe use the same WEP password for wireless stuff. I need to take note of with this working outer so I can apply it to the new router while I still have a working network with all its setting to refer to before I take the network down.
I recenly installed LMS 4 on a windows 2008 R2 system , I didnt change the default configuration of windows or ciscoworks.I just added devices and configured basic things on the LMS system .when I open ciscoworks on the server itself it starts a browser session on http port 1741 and then changes automatically to https even though the default config is browser security disabled on ciscoworks.I try to open a browser session on a mgmt station to the cisco server , it didnt work in https ( I did get the login screen but couldnt log on , probablly something to do with the certificate ) , so I open http on port 1741 and it worked , I was able to log in .After a few Hours for some strange reason I didnt have access any more from the mgmt station not in http nor in https , the only way was to access it from the server itself.I went and changed the default setting of the secure browser on LMS 4 hopping that would work , I was asked to restart the ciscoworks service for the changes to take affect , I tried to restart it but it was unsuccesful so I restart the whole server. when it came up ciscoworks didnt work most services didnt start ( like the web server ,tomcat and all the manual services and ciscoworks deamon)
View 1 Replies View RelatedI am facing two issues in BGP both the topology and Config files.Because the link between Vail and Telluride runs iBGP, both routers will learn about the networks in AS 300 and AS 400 through native BGP only and both AS's do reach each other. Both routers are also running OSPF with Aspen and BGP routes are redistributed into OSPF domain. Now, Aspen knows about the networks in AS 300 and AS 400. Now suppose the link between Vail and Telluride fails, both AS 300 and AS 400 can't reach each other anymore. The only solution to this is to redistribute OSPF routes to BGP on Vail and Telluride. But when i did this, only routes with "O" learned by Tahoe and Alta. In other words, Tahoe sees only 192.168.1.220, 192.168.1.196 and Alta sees only the same routes. Why the redistribution from OSPF to BGP didn't advertise the O E2 routes?
This actually was discussed before but i still can't get it. It is not an actual issue.It is about "Syncronization". I know that we've said many times to turn on Sync. when we do redistribution from BGP to an IGP to make sure that the routes are installed correctly in the IGP routing table. However, as you notice in the configuration, i didn't enable Sync. on Vail and Telluride for a long time and redistribution still works fine.
I have CiscoWorks LMS3.2 with RME4.3.1 and CS 3.3.0.
When I will update the devices and I go to Common Services - Software Center Device Update and I mark Resource Manager Essential then I receive this window:
Now I choose the Rtr2900 package (same problem for all six packages) and when I will download it, then after define the destination path for the file I see this window:
Then I have tried to download it manually with the following command: PSUCli.bat -p rme -d -dst c:psu_download -all
The six packages that are showed in the picture above were not downloaded.
I assume that there is an error on Cisco side because the size of the six packages is NA.
Or is there another possibility to download the package for the Rtr2900?
From one day to the next our UPM database (upm.db) has blown up from 4 Gb to 35 Gb.Data purging didn't reduce the size of the db.What happened ? And how can I compact the db again ?
View 4 Replies View RelatedI've a customer who has netManager 1.0 and they want to upgrade to CUOM 8.6. I didn't find any upgrade document for netManager 1.0 upgrade to CUOM 8.6.
View 0 Replies View RelatedI was in the process of creating a AAA setup on my NX-0S (MDS9148), logged out/attempted to login to test AAA login and now I can no longer login as admin either! I didn't change the local account. I have the Cisco Device Manager open still (in the fabric switch) and how I remedy this (AAA is not up and running as of yet with this switch).
View 3 Replies View Relatedi have router 7200 , one of its power supply stops working , but lms 4.2 doesn't notify me?
View 6 Replies View Relatedi bought a Linksys E2000 router. When i went to set it up, i noticed that the old router has a phone line connected to it. When i looked at my E2000, I noticed that it didn't have a phone port in it (Rj11). Not sure what to do. Would it be possible to buy a Rj11 to Rj45 converter and just use that to connect the phone line to my router?
View 1 Replies View RelatedI am purchasing a new DIR 600. It pings properly, but didn't access internet. I am using HP Desktop and ORTEL broadband connection.
View 1 Replies View RelatedI have a Linksys wrt110, and we didnt have a password on it for a while, i went and changed it so we had a password,now i have put a password on it, and now it wont let me connect any device to the internet, checked iphone and mac, nothing will work.
View 2 Replies View RelatedI'm trying to get several VPN tunnels up. It seems that only 1 map can be assigned to the WAN interface (fa4). Is this true or is there an 'extended' map like ACLs?
View 1 Replies View Relatedmy sister gave me an old ethernet switch so I could use the internet on my computer and my PS3. Unfortunately I didn't get any type of setup manual so I downloaded one off the manufacturer's website
View 1 Replies View RelatedI just bought the WAG120N , firmware version is v1.00.12, but it seems it has a problem with the device here.I have to turn off the system / device every time i want to get my dynamic ip update into dyndnds.org , it cant auto update the new dynamic ip.What problem that cause somethin like this?I already upgrade the firmware into 1.00.16 , but it didn't solve the problem.
View 1 Replies View RelatedI've setted the unit in BRIDGE MODE, and attached on it 3 LAN devices, 1 PC Desktop, 1 NAS WDBE and 1 HP printer ... OK all config process was right and all my units talk togheter via AP Netgear DNG2000, and so i can use for instance the printer with my laptop too connected in WI-FI N. Now usually, In the night I turn off all my devices (DAP included), and when in the morning I need only the printer used by my laptop, obviously I turn on ROUTER - BRIDGE - PRINTER - LAPTOP but NOT the DESKTOP ... and so the DAP can't reconnect automatically to the router (both the lights AP/BRIDGE are on and fixed) ... I turn on the PC and the BRIDGE reconnect to the world .... BUT I DON'T WANT turn on everytime the desktop !
1) all gears has fixed IPs
2) DHCP server deactivated on the AP main router (DNG2000)
3) no WPS used, only WPA2-PSK (AES) personal keys on all gears
once that DAP-1522 is connected to the router .... all work fine (also when I turn off the DESKTOP).so the workaround is never turn-off the DAP ? I can't believe ... and who will save the energy planet
I installed windows 8 X64 on dell inspiron 5220 and it didn't recognized the wireless device .It also rejects its win7 driver due to known comparability issue. Where can I find the driver?
View 1 Replies View RelatedI an aware the SR520 is no longer made, But we use the VPN Remote aspect of it (For site to site UC540 installs), is there anything else that has the same VPN functionality, and what would i be looking for in regards to terms for the client to be on the router itself?
View 0 Replies View RelatedHaving problems configuring an SR520 to support SSL VPN with Active Directory authentication. I set up the domain and a user in the SR520. and get the login prompt remotely but when attempting to login using the active directory account i get a login error. I can login fine using local authentication.
View 5 Replies View RelatedI just received a new SR520-FE router and am having a hard time getting it configured right. AS of now it is in my lab in a simulated "customer environment". I can ping what's behind it, what's in front of it. But I can't get outside access. I know it's probably something small so I am hoping another pair of eyes might be able to see what I don't. Here is the running-config. It's the factory setup minimally adjusted.
SR520 Base Config - MFG 1.0
User Access Verification
Username: ciscoPassword: SR520#show runBuilding configuration...
Current configuration : 6177 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname SR520!boot-start-markerboot-end-marker!logging message-counter syslogenable secret 5 $1$m/V3$CM6/dHniD1KgHsPZV6jV70!no aaa new-model!crypto pki trustpoint TP-self-signed-
[code]....
I have a SR520 where WAN configured as PPPoE with Dyndns address. I have done all the configuration through the CCA, so far everything is working fine. But now i want to configure SSL VPN, but I have getting an error message : SSL VPN cannot be configured, please configure wan interface using a static IP address. Is there any way that I can configure the ssl vpn through a dyndns address?
View 5 Replies View RelatedHow to install an SSL key + certificate on our SR520 from the CLI. I have found the following document.
[URL]
I basically have the following files that I need to install:
Key file:
domainname.key
Certificates file:
AddTrustExternalCARoot.crt
[Code].....
I am having an issue get an EZVPN working between a 2811 server and a SR520 client. The symptoms are the SR520 makes multiple connection attempts to the 2811. It appears that sometimes these connections are successful and the SR520 is assigned an IP address but then the tunnel will be dropped and a new session will be started. I've attached scrubed configs for both the 2811 and the SR520. One other note, when connecting to the 2811 with a software VPN client, there are no problems, so I think the problem is with the SR520. On the other hand, the SR520 wasn't having any problems until we switched our VPN server from a UC520 to the 2811.
View 3 Replies View Related