I upgraded my fireware and now the router don't do anything, I can't even login into it using [URL] which a hard wired connection. How do I get logged into the router to try and put the old version of firmware back on it?
View 4 RepliesI have cisco sr520 adsl router i have everything set up and it is ok. Internet work but i can not open some web pages In DNS is not problem NAT work fine. When i try some simple adsl gateway the problem websites work correctly. I think the problem is on sr520 router.
View 5 Replies View RelatedMy SRP526W (running the actual firmware 1.01.27) didn't recognize my new Huawei E372 USB dongle (it's a T-Mobile web'n'walk Stick Business II, already installed the newest firmware 11.203.03.10.55).Using a Huawei E172 or a Huawei E353, both USB dongles works well. But they are slow compared to the E372. I'd really like to use the E372 stick because it's super fast with up to 42Mbps download speed.As I could read in the release notes of the SRP526W, the Huawei E372 should be supported since firmware version 1.01.26.Inside the Huawei E372 you can find the printing "Model: E372u-5", maybe this is a different model which is currently not supported by the SRP526W.
View 0 Replies View RelatedI want to make a question about RV042. I used RV042 router in my office. I used content filter feature in router.Althought this have not been apply the rules. I think I made wrong rules.I enabled the block enable forbbiden domain .And then added the websites that I want block.However, these websites are still browsing in local computer.
View 4 Replies View RelatedI restarted my pix firewall cisco pix 515 and when i start it again the Act lamp and the firewall didn't work .
View 1 Replies View RelatedSo, using a standard off the shelf UNMANAGED gigabit switch (just a cheapie), I have a scenario that I need to know about before I go and buy a whole lot of equipment.Ok so let's start off and say it's a perfect world and the workstations connect at a full 100 Mb/s and the server connects at 1000 Mb/s.So I'm looking at having say, four or five workstations connected to the gigabit switch (at 100Mb/s) and also a gigabit connection from the switch to the server. In this scenario, taking into account everything I've said above, would each of the workstations get a full 100 Mb/s to the server, or would everything be limited to 100 Mb/s total? I could see potential for the server to only talk to one of the workstations at a time and only at 100 Mb/s, but hopefully all four could communicate to the server simultaneously.
View 3 Replies View RelatedIs it possible to limit the bandwidth of one Mac on a wired network (only medium is the Netgear router WPN824v2)?
Both are Mac. Mine is newest iMac. Other one is a MDD PowerMac. Both are OS X. Mine is Lion.
I need to be able to throttle the bandwidth of the other computer.
How can I tell if the ATT Data Service on my iPad is going through an ATT Carrier Grade NAT router or proxy server? Why I can't tell.
1. iPad does not have an interface that shows the assigned address on the Data Connecton or access to any terminal commands.
2. The reported ATT (Cingular) address is 166.147.103.208 if you use a What-Is-My-IP type of service. On a Verizon (not ATT) iPad I can ping all the way back to the iPad and turning the iPad off stopped the Ping Response . . . but there is no answer when I ping the ATT iPad 166.147.103.208 and Trace Route to the iPad stops answering at the border of the ATT network.
3. If I make a page request on an IIS web server from the ATT iPad, the web server logs 166.147.103.208 (see above) as the source address and logs the iPad as the source device, but 166.147.103.208 could still be an ATT proxy, not the iPad because some NAT routers change the source IP address to themselves.
We want to use an ATT Hotspot as the the permanent always-on home internet service where there is no other option (except satellite). We need dynamic DNS at the home, and that requires a routable public address on the ATT-hotspot. We are guessing the iPad and HotSpot would be using the same ATT network.So how can I tell if the iPad has an ATT address that can be reached from the internet (no proxy's or carrier grade NAT routers)
When I plug my desktop into my wireless router I have slow internet but when I plug directly into the modem I have no connection at all. It says "cannot connect to primary DNS server". I'm using a Motorola SURBOARD SB6121 and a NETGEAR WPN824V2 Wireless Router. When I do ipconig /all this is what I get:
View 11 Replies View RelatedI have recently purchased six quantities of DIR-655 for my home use. When I registered them these six product, at the end of each registration, I got the message that I will get an email confirming the registration.I didn't get any email. I have checked my email span box and filter too.
View 6 Replies View RelatedI am switching out routers. I have some ports forwarded that I know I need to copy down so I can open them up on the new one, but besides that, what else do I need to do/know before replacing the old for the new?Currently, we have a TRENDnet TEW-431BRP. We are replacing it with a Netgear WNR1000.Is the new one good? I didn't set up our home network. Someone from my dads previous business and friend did it for us. So I don't know what exactly was done in the router settings to set everything up.
I figured just copy the ports that needed to be opened in the new router and maybe use the same WEP password for wireless stuff. I need to take note of with this working outer so I can apply it to the new router while I still have a working network with all its setting to refer to before I take the network down.
Problem Host A unable to reach Host B, trace route from Host A it reach to Router B but the packet unable reach to the Host B here the 1st level troubleshoot I did
1. Traceroute and ping success from router A to host B
2. Ping success from router B to host B success
I wonder the packet reach to router B but it didnt pass to Host B.
i bought a Linksys E2000 router. When i went to set it up, i noticed that the old router has a phone line connected to it. When i looked at my E2000, I noticed that it didn't have a phone port in it (Rj11). Not sure what to do. Would it be possible to buy a Rj11 to Rj45 converter and just use that to connect the phone line to my router?
View 1 Replies View RelatedI am purchasing a new DIR 600. It pings properly, but didn't access internet. I am using HP Desktop and ORTEL broadband connection.
View 1 Replies View RelatedI have a Linksys wrt110, and we didnt have a password on it for a while, i went and changed it so we had a password,now i have put a password on it, and now it wont let me connect any device to the internet, checked iphone and mac, nothing will work.
View 2 Replies View RelatedI recenly installed LMS 4 on a windows 2008 R2 system , I didnt change the default configuration of windows or ciscoworks.I just added devices and configured basic things on the LMS system .when I open ciscoworks on the server itself it starts a browser session on http port 1741 and then changes automatically to https even though the default config is browser security disabled on ciscoworks.I try to open a browser session on a mgmt station to the cisco server , it didnt work in https ( I did get the login screen but couldnt log on , probablly something to do with the certificate ) , so I open http on port 1741 and it worked , I was able to log in .After a few Hours for some strange reason I didnt have access any more from the mgmt station not in http nor in https , the only way was to access it from the server itself.I went and changed the default setting of the secure browser on LMS 4 hopping that would work , I was asked to restart the ciscoworks service for the changes to take affect , I tried to restart it but it was unsuccesful so I restart the whole server. when it came up ciscoworks didnt work most services didnt start ( like the web server ,tomcat and all the manual services and ciscoworks deamon)
View 1 Replies View RelatedI am facing two issues in BGP both the topology and Config files.Because the link between Vail and Telluride runs iBGP, both routers will learn about the networks in AS 300 and AS 400 through native BGP only and both AS's do reach each other. Both routers are also running OSPF with Aspen and BGP routes are redistributed into OSPF domain. Now, Aspen knows about the networks in AS 300 and AS 400. Now suppose the link between Vail and Telluride fails, both AS 300 and AS 400 can't reach each other anymore. The only solution to this is to redistribute OSPF routes to BGP on Vail and Telluride. But when i did this, only routes with "O" learned by Tahoe and Alta. In other words, Tahoe sees only 192.168.1.220, 192.168.1.196 and Alta sees only the same routes. Why the redistribution from OSPF to BGP didn't advertise the O E2 routes?
This actually was discussed before but i still can't get it. It is not an actual issue.It is about "Syncronization". I know that we've said many times to turn on Sync. when we do redistribution from BGP to an IGP to make sure that the routes are installed correctly in the IGP routing table. However, as you notice in the configuration, i didn't enable Sync. on Vail and Telluride for a long time and redistribution still works fine.
I have CiscoWorks LMS3.2 with RME4.3.1 and CS 3.3.0.
When I will update the devices and I go to Common Services - Software Center Device Update and I mark Resource Manager Essential then I receive this window:
Now I choose the Rtr2900 package (same problem for all six packages) and when I will download it, then after define the destination path for the file I see this window:
Then I have tried to download it manually with the following command: PSUCli.bat -p rme -d -dst c:psu_download -all
The six packages that are showed in the picture above were not downloaded.
I assume that there is an error on Cisco side because the size of the six packages is NA.
Or is there another possibility to download the package for the Rtr2900?
From one day to the next our UPM database (upm.db) has blown up from 4 Gb to 35 Gb.Data purging didn't reduce the size of the db.What happened ? And how can I compact the db again ?
View 4 Replies View Relatedmy sister gave me an old ethernet switch so I could use the internet on my computer and my PS3. Unfortunately I didn't get any type of setup manual so I downloaded one off the manufacturer's website
View 1 Replies View RelatedI just bought the WAG120N , firmware version is v1.00.12, but it seems it has a problem with the device here.I have to turn off the system / device every time i want to get my dynamic ip update into dyndnds.org , it cant auto update the new dynamic ip.What problem that cause somethin like this?I already upgrade the firmware into 1.00.16 , but it didn't solve the problem.
View 1 Replies View RelatedI've a customer who has netManager 1.0 and they want to upgrade to CUOM 8.6. I didn't find any upgrade document for netManager 1.0 upgrade to CUOM 8.6.
View 0 Replies View RelatedI've setted the unit in BRIDGE MODE, and attached on it 3 LAN devices, 1 PC Desktop, 1 NAS WDBE and 1 HP printer ... OK all config process was right and all my units talk togheter via AP Netgear DNG2000, and so i can use for instance the printer with my laptop too connected in WI-FI N. Now usually, In the night I turn off all my devices (DAP included), and when in the morning I need only the printer used by my laptop, obviously I turn on ROUTER - BRIDGE - PRINTER - LAPTOP but NOT the DESKTOP ... and so the DAP can't reconnect automatically to the router (both the lights AP/BRIDGE are on and fixed) ... I turn on the PC and the BRIDGE reconnect to the world .... BUT I DON'T WANT turn on everytime the desktop !
1) all gears has fixed IPs
2) DHCP server deactivated on the AP main router (DNG2000)
3) no WPS used, only WPA2-PSK (AES) personal keys on all gears
once that DAP-1522 is connected to the router .... all work fine (also when I turn off the DESKTOP).so the workaround is never turn-off the DAP ? I can't believe ... and who will save the energy planet
I was in the process of creating a AAA setup on my NX-0S (MDS9148), logged out/attempted to login to test AAA login and now I can no longer login as admin either! I didn't change the local account. I have the Cisco Device Manager open still (in the fabric switch) and how I remedy this (AAA is not up and running as of yet with this switch).
View 3 Replies View RelatedI installed windows 8 X64 on dell inspiron 5220 and it didn't recognized the wireless device .It also rejects its win7 driver due to known comparability issue. Where can I find the driver?
View 1 Replies View Relatedi have router 7200 , one of its power supply stops working , but lms 4.2 doesn't notify me?
View 6 Replies View RelatedIs there any chance the Wireless Repeater mode work with WPA2-AES ?If not, which model of AP should I buy to connect it with my wap54g as Wireless Repeater?
View 4 Replies View RelatedI'm trying to set up my DIR-655 so I can use VPN to access my work PC. How can I set this up?
View 2 Replies View RelatedI have a DIR-655 B1 router. The firmware is 2.00 NA. Just to clarify, the DSi itself does work with WPA, but the games only work with WEP. I made a guest account and set it to WEP and it still does not work. I have tried making the main connection WEP as well, but when I go on the game and try it, it says it is WPA and not WEP. My friend has a DIR-655 as well, but the hardware and firmware version are different. Her games work flawlessly.
View 10 Replies View RelatedIf we have two public IP Address(we get it from an ISP)the First:
-IP 178.11.xx.xx with subnet 255.255.0.0 the Second:
-IP 178.11.yy.yy with subnet 255.255.0.0
Can we make the first IP work as gateway to the second IP? or we must use specific IP ??
Since thunder caused a brief shortage a week ago, I have been getting this error a lot:So when and how does this happen? Some of the time, all sites work perfectly. The rest of the time, about half the sites I try to visit yield this error. I might be browsing Website X for a while, and spontaneously, I start getting this blank screen error message for every page on that site. Unreachable sites usually start working within ~10 minutes though. Some sites always work (e.g. Reddit and Google, but not always the images in Google Images).If I try this on my laptop, using the same network cable, everything works perfectly. My computer is the only one in the house that has this error, for some reason.I have tried "ipconfig /flushdns", "ipconfig /renew", Google's DNS and OpenDNS, the "repair connection" thingie in Windows XP, restarting the server (well, my dad has), opening sites in Internet Explorer (I usually use Firefox) and unplugging/replugging my router.I haven't had any success although I have twice been tricked into believing that I've solved the problem, since all sites have randomly decided to work for a few minutes (non-reproducable of course).
View 7 Replies View RelatedI've never had this problem before with my ISP (Knology).But supposedly they had a scheduled maintenance real early this morning before 6 AM.Well, ever sense they did maintenance the router will not work and neither will my old one. The new router is a netgear, the old one is a linksys.I called them a few times and everything they had me try did not fix the problem.I can get internet access connected directly to the modem just can't get the router to work.When I right click and diagnose the problem it tells me that it's a connectivity issue with the modem. When I use my old linksys router and diagnose the problem it tells me that the DNS server is not responding.I have also tried resetting the new and old routers to default settings and started fresh.
View 16 Replies View RelatedHave a Fujitsu Siemens Esprimo P2430 PC and am trying to connect it to my Virgin Media super Hub via a Netgear WN1111 USB 2.0 AdapterWireless-N. Software is loaded perfectly fine and signal is excellent but it refuses to load any web pages unless I refresh a zillion times. Internet works excellently on my laptop so am stumped. No connection malfunction is diagnosed
View 8 Replies View Related