Cisco LAN :: Unable To Configure 887 Router?
Apr 6, 2012
i am having trouble in configuring my cisco router 887. my connection type from my ISP is static ip. im not sure if i have entered the correct command in the CLI.
router(config)# interface fa 0/0
router(config-if)# ip address 61.10.XX.XX x.x.x.x
what would be the command to do this?and also, i want my other PCs to receive DHCP ip address from the router.
View 2 Replies
ADVERTISEMENT
Feb 28, 2012
I am using D link Wireless router and the Model is DI-524 I am unable to configure the router with static Ip as the ISp having Static Address.
View 4 Replies
View Related
Nov 5, 2012
What is the reason of following NTP error. I am unable to configure further ntp peers on the router. Could not able to understand the reason of 100 peers. I am adding only 2nd peer on the router but getting this error. There is no problem adding peers in other 6500s .
View 2 Replies
View Related
Jan 29, 2012
I have a Cisco 2911 router that I will like to use it for setting up a site to site VPN but the router does not support VPN commands. When I issue crypto isakmp command, it says command no recognized. When I issue ipsec transform-set command, it says command not recognized. The IOS running on my router is c2900-universalk9-mz.SPA.151-2.T1.bin. Also see the output of my show licences features command: [code]
what can be done on this router to enable use it for setting up a VPN connection.
View 6 Replies
View Related
Dec 8, 2011
I have installed a DIR615 N Router and can get onto the Internet on the PC, but when I type in the device IP address it comes up with an "error" message so I cannot configure it.
View 6 Replies
View Related
Mar 8, 2011
I have a (Air Access) - ZG-5000-11g Wireless Outdoor Bridge , Ap Router, It has hanging problem, so I make it factory default. but now I have unable to configure it. find out default ip address.
View 5 Replies
View Related
Oct 17, 2012
So I have a dsl modem (Tplink TD-8817) that i connected to my other route that has wifi(CBV734EW ). I configured them using this thread: [URL]
Now the problem: My pc that is directly connected with lan to my wifi router has acces to the internet. However when i try to configure the wifi router by going to its ip (192.168.0.1) im getting "The webpage unavailable" error. And i am also able to connect to my dsl modem(192.168.0.2) The reason i want to configure my wifi modem is the fact that for some reason only 1 wifi device at a time seems to be able to have acces to WAN.
View 4 Replies
View Related
May 30, 2011
i have a ZyXel prestige 650H-31 Model # router and i'm not able to go on to configuration page of the router i tried 192.168.1.1 several times, even after system reboot and router reset, but of no use. I've a wire connection with desktop (RJ-45 port) not USB AND MY PPPoE lights never lit. originally when i entered the gateway 192.168.1.1 it asked me for username & password, since i didn't have the password at that time i tried to reset the router but after that when ever i entered 192.168.1.1 in the browser it never came up with the option to enter user name & password. I've checked all the wires are also connected. I tried prompt command and it showed that timed out thrice and then sent= 4 received= 0 lost= 100%. I had D-Link router prior to it and later connected the D-Link router an i was able to get connected to net and browse normally.
View 1 Replies
View Related
Mar 17, 2012
I have a Hawking 300N and I have misplaced my disk and I neing walked through this to have it set back up. I hooked it all up correctly and it says no internet connection
View 1 Replies
View Related
Feb 18, 2011
I just picked up an e3000 last night. Set up was performed manually. Flashed to 1.0.04. No issues and I was up in under 10 min.Although I read the user guide, prior to purchase, I admit I did not expect that I would not be able to configure ALL of the router's features and functions from the web based configuration, without using the CISCO Connect CD.Parental Controls and GUEST Access cannot be configured unless you load the Cisco Connect software.While this is not a huge deal, this implementation is clumsy and cumbersome for advanced users. Honestly, I had no disire to install the Cisco Connect software. I was further disappointed to see that it stores the router's password.
My feeling here, let's not ruin a great thing. There are two types of users. One's who need a configuration wizard, and other's who don't. I guess some inroads are being made in the right direction as some GUEST access functions can be made in the web gui on the e4200. I hope this can be further expanded to all "e" series routers in the future. Overall, it works as advertised. Streaming 720p HD video over wireless 2.4Ghz band G only is flawless. This is no different than my wrt54g2, but I'm upgrading to a 1080p player and have read that N on the 5Ghz band is the way to go.
View 1 Replies
View Related
Apr 25, 2011
I am not able to configure Service policy output command in Cisco 2921 router.While configuring I am getting below error.Same config is working fine in Cisco 3845 router.I am suspectting the problem with license in IOS.
View 3 Replies
View Related
May 2, 2011
i am unable to configure my netgear router with my clear modem
View 1 Replies
View Related
Mar 13, 2013
Region : India
Model : TL-MR3020
Hardware Version : V1
Firmware Version :
ISP : BSNL
I'm unable to configure my Data Card (ZTE-AC8700). I tried with manual settings but it keeps on showing the message "connecting" but doesn't connects although my datacard is shown as identified by the device MR-3020. I'm using BSNL EVDO connection and my datacard is ZTE-AC8700. It doesn't uses any APN, only a username and password and dial number "#777" is required to connect. configuring my datacard with MR3020 ???
View 2 Replies
View Related
Feb 17, 2013
We have an ASA 5520 with two VPN profiles working fine.Since some users are now working with Windows 8, VPN clients for Cisco ASA is not able to connect.I have read there are problems for such VPN Clients in that OS, and I should use now Anyconnect for them to connect. I thought we had anyconnect working also, because some users can connect to a web page they can do some kind of connections to internal servers, (web, telnet, rdp, etc) so I installed cisco anyconnect VPN client in a laptop and try to connect (same IP and port I used for that web page) but after signing I get the message AnyConnect is not enabled on the VPN Server.So I tried to follow a configuration guide for Anyconnect, but there's a step in which I am trapped, these are the steps: Click Configuration, and then click Remote Access VPN.
View 7 Replies
View Related
Aug 5, 2011
How to config RDP to internal host from outside. With new OS, unable to configure RDP having issue with NAT commands are different.
View 1 Replies
View Related
Jun 15, 2011
I have an ASA 5510 and I can not configure fine.
My problem is that I have 10 public address connected to ASA and each public address is redirectioned to an internal IP address.
An of these public address is the ip address of mi ASA.
how to configure and access-list and an NAT, the others I will configure.
interface Ethernet0/0
description Interface_WAN_World-Ttrends
speed 100
duplex full
nameif outside(code)
View 59 Replies
View Related
Aug 24, 2012
Just got hold of my first 887va for my home, never configured a vdsl interface before and was just wondering if my setup looked good to someone whos done it a few times.
View 6 Replies
View Related
Apr 2, 2012
I have a BSNL wifi modem WA3002g4 . i am unable to configure the modem192.168.1.1 site does not respond
View 1 Replies
View Related
Jun 22, 2011
I am not able to configure the wifi user and password after configure the ssid & passord it is not working according to my requirement
View 1 Replies
View Related
Jan 29, 2013
I'm trying to do configuration archiving in Prime Infrastructure 1.2 with a 5508 WLC (7.4).The job always fails (Admin -> Background Jobs) with the following error (see attachement):"SNMP: Failed to establish SNMP connection xxxx - Cause: Device is Unreachable. Check the ReadOnly community string." I double checked the SNMP credentials, they do match. For testing I also added a Public community just for the PI. Same result.Am I missing something?Is this not intended for Wireless Controllers?
View 5 Replies
View Related
Sep 17, 2008
I'm trying to access the WAP200 for the first time. Instructions say Configure your PC to have the static IP address on the same subnet as the Access Point's default address (http://192.168.1.245). So I assumed i would go to TCP/IP properties and type in IP address and subnet mask and the Utility would open.
View 3 Replies
View Related
Sep 14, 2011
I just received a Cisco Aironet 1130 AG wi-fi router to configure and when I entered the router through console, I am not able to get into config mode. It says:
[code]....
View 9 Replies
View Related
Jan 15, 2012
I am trying to configure etherchannel on 2 2960S connected by a flexstack with 2 ports g1/0/52 and g2/0/52 on each 2960.
these switch are connected to a CAT4500, I know that I can only use LACP because of cross-stack but when I force the switch to use LACP witch channel-group 2 Mode active the switch do this :
%With PAgP enabled, all ports in the Channel should belong to the same switchCommand rejected (Port-channel2, Gi1/0/52): Invalid etherchnl mode
% Range command terminated because it failed on GigabitEthernet1/0/52
I don't know how to bundle the 2 ports on the 2960 stack. each time I use : channel-group 2 mode on there is no error
but the switch do this :
*Mar 1 00:45:32.290: %EC-5-CANNOT_BUNDLE2: Gi2/0/52 is not compatible with Po2 and will be suspended (trunk mode of Gi2/0/52 is dynamic, Po2 is trunk)
*Mar 1 00:45:32.531: %EC-5-CANNOT_BUNDLE2: Gi2/0/52 is not compatible with Po2
[Code].....
View 9 Replies
View Related
Mar 26, 2012
I am having trouble trying to configure my cisco 2509 cisco router for access server. I have two guides shown below: URL and URL
However I am running into some problems. I can go through the second guide up until it asks me to do this command
Step 5: Configure the transport input protocol on the async lines to Telnet.
Access_Server(config-line)#transport input telnet
I cannot put in Transport Input, I only have the option of doing Transport Output let me show some lines from my console:
---------------------------
Access_Server(config)#line 0 14Access_Server(config-line)#no execAccess_Server(config-line)#transport input ?% Unrecognized commandAccess_Server(config-line)#transport ? output Define which protocols to use for outgoing connections preferred Specify the preferred protocol to use
Access_Server(config-line)#transport
------------------------
Im not sure whats going on. I have two routers(cisco 2600 series) plus my 2509 cisco router I am going to use for a access server. I have a two switches 2950 series and I have the access server connected to all of them via a octal cable.
Here is the configuration from the access server:
--------------------------------------
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-IS-L), Version 12.3(26), RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Mon 17-Mar-08 14:39 by dchih
cisco 2509 (68030) processor (revision M) with 14336K/2048K bytes of memory.
Processor board ID 22840809, with hardware revision 00000000
Bridging software.
View 7 Replies
View Related
Sep 14, 2012
I am configuring Site-to-Site VPN with another company. I already make a couple of tunnels but with this one I have a problem. They I already using on their side my local network 192.168.10.0/24 (server is 192.168.10.10) so we need to use imaginary network 172.16.0.5 as server address. Now I need to do NAT 172.16.0.5 to 192.168.10.10 but I am not so good in that.
View 1 Replies
View Related
Dec 28, 2012
Is it possible to configure a E2500 as router and WAP54G as a repeater? I used to have a WRT54GS as router but it has broken and now I bought a E2500 to replace it.
View 2 Replies
View Related
Jan 23, 2011
My boss want me to configure a cisco router 1800 series to an IP VPN, but I don't know how to configure a router with an IP VPN...
View 2 Replies
View Related
Jan 17, 2012
how to config wrv 210 wireless-G vpn router config.
View 0 Replies
View Related
Feb 14, 2012
I have a question, it is possible to have two WAN interfaces to configure a cisco 892 router with an ip 255.255.240.0 84.197.167.111 adderess of the first interface and a different ip address 84.197.174.182 255.255.240.0 on the second interface
View 5 Replies
View Related
Dec 13, 2010
how I configure netflow on a cisco 877 router.
I have an interface e0/4 that is 172.1.1.1 on router one (network one) which links to another router (onnetwork two) which has an interface of e0/4 172.1.1.2 which allows two networks to communicate. Network one is 192.168.0.0 /24 and network two is 10.255.255.0 /24.
How do i configure netflow to monitor the traffic going through these interfaces?
View 1 Replies
View Related
Jun 26, 2012
I want to configure PAT on the router I have no configuration yet
View 1 Replies
View Related
Mar 22, 2011
How do i configure SSL VPN on a Cisco 1941 router? I would very much want a howto guide that does step by step. I have not found one my self so far.
View 1 Replies
View Related
Dec 24, 2012
setup a vpn server cisco.
device cisco router 1841 [URL]
View 2 Replies
View Related