DI-524 - Unable To Configure The Router With Static Ip?
Feb 28, 2012I am using D link Wireless router and the Model is DI-524 I am unable to configure the router with static Ip as the ISp having Static Address.
View 4 Replies
ADVERTISEMENT
Cisco WAN :: Configure 861 Router For Internet Using Static Ip Address?
Apr 5, 2013I am having a cisco 861 series router.The Cable from the isp was connected to fastethernet4(wan port)
Following are my isp details
IP address:172.16.62.130
subnet:255.255.0.0
default gate way:172.16.62.1
dns primary:202.153.32.2
secondary:202.153.32.3
How do i configure this details in the router and access the internet in my devices.
i want the network to be in 192.168.1.0 to 254.
how do i configure my router with this details using cisco configuration professional
Linksys Wireless Router :: E200 How To Configure Static Routes
Mar 30, 2012how to configure it. So far googling and using the router's built-in help feature hasn't been of use. First off, here's my setup:NETWORK A with default gateway of 192.168.0.1 and a subnet of 255.255.255.0
NETWORK B with default gateway of 10.10.100.1 and a subnet of 255.255.255.0
I want B to connect to A since that's where I have my domain setup with active directory.
Now from my understanding the Destination LAN IP should be the network I want to connect to, in this case 192.168.0.1. The subnet mask should be 255.255.255.0 and the default gateway should be 10.10.100.1. However, when I do this, the LinksysE200 throws out an 'Invalid Static Route" error. What am I doing wrong? Also, here is the routing table as given by the E200:
Protocols / Routing :: Linksys WRT54G Router - Unable To Set Up Static IP?
Mar 7, 2012Comcast Cable Internet Linksys WRT54G Router (using wired, not wireless)
I've done this a million times over so I thought I knew what I was doing. I set my IP as 192.168.1.236 and get all of the information I need from ipconfig. When I put it all together though, it just doesn't work. I think I'm not getting the correct DNS information from ipconfig and the blockheads at Comcast have no idea what a name server is. I've called and talked to about twenty different people there and no one can give me my name server. *sigh*
At any rate, below is a screenshot of what I'm getting in ipconfig. My assumption is that I'm not getting the correct DNS info, but I don't even know at this point.
Linksys Wireless Router :: Unable To Access Ea4500 After Static IP Assigned
Apr 2, 2013I want to do with my ea4500 is assign it a static IP and access it after doing so. But, no matter how many times I try, I cannot enter its IP address in the address bar and see its settings. I change its IP to192 168 1 200. Subset 255... DG 192 168 1 1 DNS same.Under router address 192 168 0 1I CANNOT access this router at 192 168 0 1 at all. The thing is, the **bleep** settings are not any different the. How they were when it was WORKING. I literally took a screenshot of my setting in case a scenario like this would come up, yet it more problems arise. The only way I can access the router is by doing a factory reset and accessing it at 192 168 1 1.
View 9 Replies View RelatedCisco Switching/Routing :: Unable To Delete Static Route 1811w Router
Nov 23, 2012On 1811W Router i have OSPF running and i do not need this static route.ip route 192.168.20.0 255.255.255.0 192.168.20.3,when i try to delete i get error ,1811w#,config t,Enter configuration commands, one per line. End with CNTL/Z.,1811w(config)#no ip route 192.168.20.0 255.255.255.0 192.168.20.3,%No matching route to delete,1811w(config)#.
View 7 Replies View RelatedCisco LAN :: Unable To Configure 887 Router?
Apr 6, 2012i am having trouble in configuring my cisco router 887. my connection type from my ISP is static ip. im not sure if i have entered the correct command in the CLI.
router(config)# interface fa 0/0
router(config-if)# ip address 61.10.XX.XX x.x.x.x
what would be the command to do this?and also, i want my other PCs to receive DHCP ip address from the router.
Routers / Switches :: Unable To Configure DIR615 N Router?
Dec 8, 2011I have installed a DIR615 N Router and can get onto the Internet on the PC, but when I type in the device IP address it comes up with an "error" message so I cannot configure it.
View 6 Replies View RelatedZG-5000-11g - Unable To Configure Router After Factory Reset?
Mar 8, 2011I have a (Air Access) - ZG-5000-11g Wireless Outdoor Bridge , Ap Router, It has hanging problem, so I make it factory default. but now I have unable to configure it. find out default ip address.
View 5 Replies View RelatedCBV734EW - Unable To Connect And Configure The Slave Router?
Oct 17, 2012So I have a dsl modem (Tplink TD-8817) that i connected to my other route that has wifi(CBV734EW ). I configured them using this thread: [URL]
Now the problem: My pc that is directly connected with lan to my wifi router has acces to the internet. However when i try to configure the wifi router by going to its ip (192.168.0.1) im getting "The webpage unavailable" error. And i am also able to connect to my dsl modem(192.168.0.2) The reason i want to configure my wifi modem is the fact that for some reason only 1 wifi device at a time seems to be able to have acces to WAN.
Cisco WAN :: 6500 Unable To Configure Further Ntp Peers On Router
Nov 5, 2012What is the reason of following NTP error. I am unable to configure further ntp peers on the router. Could not able to understand the reason of 100 peers. I am adding only 2nd peer on the router but getting this error. There is no problem adding peers in other 6500s .
View 2 Replies View RelatedRouters / Switches :: Unable To Configure ZyXel Router P650H-31?
May 30, 2011i have a ZyXel prestige 650H-31 Model # router and i'm not able to go on to configuration page of the router i tried 192.168.1.1 several times, even after system reboot and router reset, but of no use. I've a wire connection with desktop (RJ-45 port) not USB AND MY PPPoE lights never lit. originally when i entered the gateway 192.168.1.1 it asked me for username & password, since i didn't have the password at that time i tried to reset the router but after that when ever i entered 192.168.1.1 in the browser it never came up with the option to enter user name & password. I've checked all the wires are also connected. I tried prompt command and it showed that timed out thrice and then sent= 4 received= 0 lost= 100%. I had D-Link router prior to it and later connected the D-Link router an i was able to get connected to net and browse normally.
View 1 Replies View RelatedRouters / Switches :: Unable To Configure The Setup On A Hawking 300 N Router
Mar 17, 2012I have a Hawking 300N and I have misplaced my disk and I neing walked through this to have it set back up. I hooked it all up correctly and it says no internet connection
View 1 Replies View RelatedLinksys Wireless Router :: E3000 Unable To Configure All Features
Feb 18, 2011I just picked up an e3000 last night. Set up was performed manually. Flashed to 1.0.04. No issues and I was up in under 10 min.Although I read the user guide, prior to purchase, I admit I did not expect that I would not be able to configure ALL of the router's features and functions from the web based configuration, without using the CISCO Connect CD.Parental Controls and GUEST Access cannot be configured unless you load the Cisco Connect software.While this is not a huge deal, this implementation is clumsy and cumbersome for advanced users. Honestly, I had no disire to install the Cisco Connect software. I was further disappointed to see that it stores the router's password.
My feeling here, let's not ruin a great thing. There are two types of users. One's who need a configuration wizard, and other's who don't. I guess some inroads are being made in the right direction as some GUEST access functions can be made in the web gui on the e4200. I hope this can be further expanded to all "e" series routers in the future. Overall, it works as advertised. Streaming 720p HD video over wireless 2.4Ghz band G only is flawless. This is no different than my wrt54g2, but I'm upgrading to a 1080p player and have read that N on the 5Ghz band is the way to go.
Cisco Switching/Routing :: Unable To Configure VPN On 2911 Router
Jan 29, 2012I have a Cisco 2911 router that I will like to use it for setting up a site to site VPN but the router does not support VPN commands. When I issue crypto isakmp command, it says command no recognized. When I issue ipsec transform-set command, it says command not recognized. The IOS running on my router is c2900-universalk9-mz.SPA.151-2.T1.bin. Also see the output of my show licences features command: [code]
what can be done on this router to enable use it for setting up a VPN connection.
Routers / Switches :: Unable To Configure Netgear Router With Clear Modem
May 2, 2011i am unable to configure my netgear router with my clear modem
View 1 Replies View RelatedRouters / Switches :: Configure 2 Static IPs Over Single Connection?
Jan 28, 2011This is the situation in our Lab.We have one telephone line with broadband connection and a system which is connected to a modem to use this broadband facility. Recently we have taken two static IPs over this connection for a project work.Now what I want to know is, how to configure these static IPs, so that I can connect two systems (each one to one static IP) to use these static IPs and continue to access the internet in the 3rd (already present) system.
View 7 Replies View RelatedCisco :: Configure 2960g Switch Static Routing?
Jan 26, 2013I have routing enabled, can build a static route, and go back and see it (sh ip route), but I don't know how to get the route right. I have one host (Host A) on Vlan 20 w/192.168.20.2/24 dg 192.168.20.11 (the vlan ip) and (Host B) on Vlan 30 w/192.168.30.2/24 dg 192.168.30.11 (the vlan ip). I can't ping them from any host man. I can ping the Vlans but not the host.
View 19 Replies View RelatedStatic IP / Configure Server 2008 For Internet Access?
Oct 9, 2012I have a static ip , So how co configure my server 2008 for the access from internet [URL]
View 1 Replies View RelatedCisco Firewall :: How To Configure Multiple Static IPs On ASA 5505
Jun 10, 2011I am setting up a Cisco ASA 5505 first time for My organisation, I usually setup Cisco Router, I have 10 Static IP, & Have 6 Server (S-1, S-2, S-3, S-4, S-5, S-6), Traffic Should be pass through the ASA and is distributed to the destination server that is specified in the packet. LAN servers can be separated into discrete networks for security. For example, a private LAN for internal traffic accessed only via remote dial-in VPN sessions and Want to Configure DMZ for Server (S-4, S-5, S-6) that allows public web traffic.
I have Attached My Network Diagram I have some question,
1:- Can we Configure Multiple Static IP On ASA 5505 ?
2:- If Diagram is wrong what change need to be done ?
Cisco Firewall :: Pix 501 (6.3) VPN / Cable Modem - Can't Configure Static IP
Sep 23, 2011I have a Pix 501 running 6.3 code sitting behind a cable modem. I use ip address outside dhcp setroute because I don't have a dedicated IP from my cable provider.
How do I configure the Pix to host VPN connections from my iPad when offsite? Since the outside interface is going to change, I can't configure a static IP.
Cisco WAN :: 3560 / How To Configure Static Routing To Different Gateway
Dec 6, 2011I have one Cisco 3560, and it is connected to Firewall...I already turn on the ip routing, which is able to do interVLAN..In 3560, the static route is 0.0.0.0 0.0.0.0 192.168.2.2
3560 (port 1) =====> Firewall (port 1) ======> Internet (WAN)
192.168.2.1 192.168.2.2
Which mean... anything from 3560 will be rote to Firewall port 1 (192.168.2.2) and all the user behind 3560 will able to connect to Internet (WAN).
I want different setup now, I'm trying to configure another port (port 2) from Cisco 3560 connect to Firewall port 2...
3560 (port 2) =====> Firewall (port 2) ======> Internet (WAN)
10.1.1.1 10.1.1.2
I want subnet 10.1.1.x route to different gateway (10.1.1.2) to Firewall go out to WAN... and not using 192.168.2.2 gateway to WAN.
Cisco Routers :: Configure SRP527w Without Static Outside Ip Address
Jul 17, 2010I need to know how to configure SRP527w without a static outside ip address to establish a VPN tunnel with VPNC3000.
View 31 Replies View RelatedTP-Link 3G/3.75G Router :: Unable To Configure BSNL-EVDO Data Card (ZTE-AC8700)
Mar 13, 2013Region : India
Model : TL-MR3020
Hardware Version : V1
Firmware Version :
ISP : BSNL
I'm unable to configure my Data Card (ZTE-AC8700). I tried with manual settings but it keeps on showing the message "connecting" but doesn't connects although my datacard is shown as identified by the device MR-3020. I'm using BSNL EVDO connection and my datacard is ZTE-AC8700. It doesn't uses any APN, only a username and password and dial number "#777" is required to connect. configuring my datacard with MR3020 ???
Cisco WAN :: Unable To Configure Service Policy Output Command In 2921 Router
Apr 25, 2011I am not able to configure Service policy output command in Cisco 2921 router.While configuring I am getting below error.Same config is working fine in Cisco 3845 router.I am suspectting the problem with license in IOS.
View 3 Replies View RelatedCisco WAN :: 12416 Configure Static Route Load Balancing
May 14, 2011I got an issue when configure my 12416 router.
I plan to configure Static route load-balancing, which just assign different administraive distance to static routes.The route with lower distance is preferred. For example, if ISP A is our primary Internet provider the default route may be configured with a distance of 1 (all static routes are assigned this administrative distance) and the default route through ISP B may be configured with a distance of 100. In that case the default route through ISP B will be used if only the route through ISP A becomes unavailable.
But when I trying to configureWith Enhanced Object Tracking to do the route failover (a generic track object can monitor presence of an ip route, state of an SLA), I found my IOS not support such Track command. [code]
Cisco VPN :: Configure Static IP Address In Remote Client ASA 5500?
Aug 13, 2011i am trying to configure static ip on remote client user side , i am using the following doc as an example but i am not getting the ip which i am mentiong in the user .[url]...
View 10 Replies View RelatedCisco LAN :: 1841 - Configure Dynamic / Static Nat With Route-Maps
Aug 4, 2009Basically I have an internet router (1841ISR) with 1 internal (LAN) connection and 2 internet connections. What I want to do is route specific traffic for 3 of my internally hosted services (smtp, https, etc) through one internet connection (fa0/0) and then route all other traffic through the unmanaged/dynamic IP ADSL connection (Dialer 0).
View 9 Replies View RelatedCisco :: Unable To Ping From Static IP?
Oct 26, 2012I am connecting a 2600 router to an ISP. Interface 0/0 is connected to the ISP using DHCP. Interface 0/1 is connected to the inside providing DHCP services to the inside. At least it should only be providing DHCP services to the inside. I also have a public static IP that is NAT to a private static IP. Everything is working except the computer on the static IP. From the router I am able to ping inside and out from each interface. I am able to ping both interfaces of the router from the computer on the static IP but I cannot ping outside the router. If I do a debug all I see a reject for the gateway of the static IP but it has “mobile IP” in the text string. Not sure what mobile IP is relating to. Networks are as follows:
0/0 DHCP 10.X.X.X
0/1 192x.x.x
Static 75.X.X.X
[Code].....
Cisco Firewall :: Asa 5520 / Configure Two Static Nat Statements From Inside To Outside And Backup Interface?
Oct 16, 2011I have a asa 5520 with an outside and backup interface. I am trying to configure two static nat statements from the inside to the outside and backup interface. Here is what I have configured so far.
object network obj-10.1.1.254
host 10.1.1.254
object network obj-10.1.1.254
nat (inside,outside) static 172.25.10.3
I want to also use nat (inside,backup) static 172.25.10.3
Cisco Firewall :: Configure HTTP Traffic To ISP2 And Static NAT To ISP1 On ASA5520?
Jun 20, 2011is this possible to configure HTTP traffic to ISP2 and Static NAT to ISP1 on ASA5520?
View 2 Replies View RelatedCisco Switching/Routing :: SRW2024-K9-BR / Switch To Configure Static ARP Entry For MS NLB Multicast?
Mar 14, 2013I need a switch to configure a static ARP entry for a MS NLB multicast.
Could answer me if I can do with the SRW2024-K9-BR?
Home Network :: Unable To Ping Static Ip From Outside Campus
Nov 7, 2012I have 5 Static Ip pool all IPs are working fine. I have deploy a IIS Server on Windows2008 and configure the Static IP on that server. earlier it was working fine . but since last month the IP is not pinging from Out Side but internal IP Pool its working. I have checked the SERver firewall and another Setting is Ok. if i changed the Ip from the server the new IP is also not pinging.
View 1 Replies View Related