I have encountered an error while creating the new poller by selecting the interfacerror template.
Is it the license limitation?? if license limitation how can i find out the current devices count in the performance monitor page?
I'd like to know your experience regarding how client count affects performance.
What I have seen in a university network, with a very high client densiity, using 3500 APs, is that around 55 clients ping reply time gets over 200 ms; around 60 users there's packet loss; then, as CC increases, somewhere between 60 - 70 the service gets totally lost. Off course, this depends on bandwidth consumption per user, interference, etc.
Also, I'd like to know what we could expect from 802.11ac regarding this topic. Is there any information on tests, or some estimation already published?
if there is a MIB available for the EHWIC-4G-LTE-V card that would allow me to monitor the current RSSI level?
If I issue the command "show cell 0/1/0 radio" on my Cisco2911 router, I get the following info. I'd like to monitor the "Current RSSI" level in Solarwinds.
Router>show cell 0/1/0 radio
Radio power mode = ON
Current RSSI = -67 dBm
LTE Technology Preference = AUTO
LTE Technology Selected = LTE
It is required to monitor newly placed WAN link performance . How can I configure my cisco 1841 router to obtain the following information.
1) Errors
2) Jitter
I am having some question around Prime Infrastructure..Does a general document exists regarding the licensing count of monitored devices ? Indeed I am wondering about the specific points. Is it true that :
- A 3750 stack unit count as one (for example a 4 units stack consumes 4 license) ?
- A WLC (except 5500) does not consume a license but only the Lightweight APs.
- An autonomous AP does not consumes a Lifecycle licence ?
I have an AT&T Router that is my gateway to the internet, I have no access to it. I do have the inside ip address of it which is on my private LAN. Just for shiggles we will call it 10.25.240.1 255.255.248.0. That is my gateway address for all of my current devices.I have this shiny new ASA that I want to throw in there to eliminate a proventia and a sidewinder.
The diagram shows two stacks, these are my virtual server clusters with 3560X switches with the vlans configured, and several more switches all configured with vlan 832, connected to a 2950, which is connected to my internal 2600 router. I have 4 Vlans running on 4 different ip ranges, all controlled by the internal router, with only one vlan, let's say 832 that is trunked to the outside world. That vlan has 172.16.1.x 255.255.0.0 network attached to it. All is well, and traffic is routing behind the internal router, but I cannot seem to figure out how to get the traffic to pass thru the ASA. [code]
how to find the current logged on user on a domain network? I tried nbtscan but it gives me ip address, machine name and mac address. In the server column it gives <server> and in the user name column it give <unknown>.
View 1 Replies View RelatedDespite there are all devices are managed in DFM (accorduing to Collection Summary Portlet or Rediscover devices) there are no devices in the Fault Monitor with the message "No devices are available"Does it mean, we have absolutly no faults in our network or does it mean that we have a problem with DFM?
View 2 Replies View RelatedI have some questions about monitor of status of services on Network Devices such as HSRP, Etherchannel (between Access ports and Servers), etc. How we can track those information in addition to Syslog. Is it possible that the Fault Monitor displays them?
View 1 Replies View RelatedMonitor a VPN tunnel that has as end devices a Cisco ASA 5520 and a NetScreen Firewall. I'll like to be receive an alert when the VPN is down.
View 1 Replies View RelatedI've got the E3000 set up and working. What I'd like to do now is monitor all the devices' connectivity to it. The bandwidth it consumes and stuff. Is there a way to do that on my router?
View 6 Replies View RelatedI am looking to track what my kids are doing on the internet. I have an ea4500 and was wondering if there is a detailed log file that I can look at?
View 3 Replies View RelatedI have load CISCO-ENVMON-MIB and initiate walk in it but unable to find OID of Cisco 2960 temperature monitor. I have search over net and found .1.3.6.1.4.1.9.9.13.1.3.1.3.1 for temperature but this OID is not responding in this mib.
View 2 Replies View RelatedI went to Furrynutz link where I never found the direct download lilnk to the widget. I then chatted with a Microsoft representative at the widget page and he linked me to the same Furrynutz's link.
My DIR-825 has the latest firmware, 2.06xx and works flawlessly, even the shareport usb port works without a hitch with a Seagate Expansion 3TB drive connected into it. What I simply would like is the D-Link gadget.
I just switched internet providers and i have wireless, since then, my boyfriends laptop is having problems staying connected to the internet. the desktop and my laptop stay connected his doesnt. it will say connected or limited access but i cant get a webpage or when i do its internet explorer cannot find page.System Info Utility version 1.0.0.1[CODE]
View 14 Replies View RelatedI turned a Belkin Surf N300 into an access point using the settings page via IP address, now I can't seem to find that page again so I can switch it back. The model number is F7D6301 v1.
View 7 Replies View RelatedThis issue just started happening. I have a Sierra Wireless Aircard 595 plugged into a WRT54G3G-ST. I will be browsing the internet and all of a sudden, I get the message that Internet Explorer cannot find the web page. At that point, I cannot get to any website. I have several PC's, both wired and wireless connected and they all have the same problem,. I have tried Google Chrome, Firefox and IE9 and all browsers have the same issue. My email continues to download through Outlook, I can use WS FTP and I can also log in to a remote computer using Logmein. It is just browser access that is affected.
There is no set time table to the error. Sometimes it happens within minutes, sometimes it is 30 minutes and sometimes it is over an hour. The only way out of it is to either unplug the router, let it set 30 seconds, then plug it back in or I found that I can go into the setup and do a disconnect from mobile broadband and reconnect and it starts working again. Of course, Sprint says they do not deal with issues unless the card is plugged directly into my PC, which is not the environment that I am running in (even though I bought the router and card from them.) Does Linksys still make a mobile broadband router?
Can't find WAG160N firmware upgrade download page on this site A few mounth ago it existed
View 3 Replies View RelatedI cant find the WUSB600n ver.2 drivers on your support page: url...When I click "Version 1.0" it shows me the Win7 driver but by clicking "Version 2.0" it just says: "Guides and Information" but theres no drivers. I suppose it's a bug.I have a new Laptop so I need the Win7 64bit driver for ver.2.
View 2 Replies View RelatedWe have a pair of Cisco 6513 switches, to which a selection of Wintel/Linux/UNIX servers are attached, but we have some connections that we can't identify and the data centre is a remote lights-out operation operated by a 3rd party in another country. determining which server NIC ports connect through (via patch panels) to which ports on the Cisco switches.In particular, I have a UNIX (HP-UX) server that has 4 dual port NICs (ie. 8 LAN ports), of which only one is assigned an IP address, but I can see that the other ports have connectivity at level 2 (HP-UX has a "linkloop" command that is analogous to an IP "ping" but takes a MAC address, and I get a response from each when I check from another server). This means that I know that there is a physical, electrical, and level 2 connection.The one server port with the active IP address set up shows in the switches address table ("sh mac-address-table") and it gives the port it is attached to. But the remaining 7 ports do not have IP addresses assigned and so are not listed in the table.
View 8 Replies View RelatedI am having a major issue trying to connect my Windows 7 HP Netbook to my Xbox 360 over either Twonky/Serviio or Windows Media Centre. The Xbox just isn't picking up my computer, my homegroup recognises the Xbox and it is 'Allowed' to share media, but when I test my PC connection within the Xbox dashboard, it fails to connect to PC. My network is wireless.The strange thing is I have TwonkyServer Mobile running on my Android phone and that was found by my Xbox immediately with no need to change settings or search for devices. It streams media just fine from my phone. This leaves me thinking that it is an issue with my PC as opposed to my router, I have double checked my router settings (Sagem 2304), UPnP is showing as enabled, I've reset and unchecked/rechecked the UPnP but still not working.
My TwonkyMobileServer is also unable to find my PC server although I have been able to find my MobileServer in Windows Media Player and stream media from my phone.Windows Firewall has been disabled, I've also Uninstalled my antivirus software, Avast and AVG, although AVG doesn't seem to want to disappear that easily and is still lurking in my System Tray telling me i've 'Lost protection'...Norton Internet Security is also lurking around which is odd, I can not recall installing it! It doesn't seem to be a fully installed version and doesn't seem to want to be uninstalled. Could these AV software and supposed Internet Security software be holding me back?This leaves me thinking that my PC is holding back my Network. Is there any thing I haven't thought of? Would it be the Anti-virus leftovers ruining my streaming dreams??
My internet comes to D-link 655 wireless router from there I have wired connection, one of the connection goes to a switch from this switch I connect wired devices in my office.Another connection from D-link 655 router goes to another wireless router in my living room which is a Linksys router. My few devices and a laptop connects to this router.My problem is I am not able to see the devices connected to my Linksys router from my office devices
View 2 Replies View Relatedi am setting up a new Monitoring System (CA Netvoyant). It has some default Cisco monitoring capabilities ( I believe these are soem standard MIBs). I am wondering how can I add more useful Cisco MIBs for the devices I have in my network. There are thousands of MIBs and it looks like it is not easy at all to find the useful ones.For example the MIBs that can give you Emergency and up to warning level information, cpu, memory, interface errors, module failures (in case of Cat 6500), FWSM, BGP, VPN tunnel status notifications. Is there a list of useful MIBs for each device type, like Cat 6500, ASA5540, Cat 3750-E etc depending on IOS Image? setting up the SNMP monitoring system?
View 1 Replies View RelatedI have recently purchased an SG-300-52 Managed Switch. (This is the first managed switch I have used, so I am trying to figure out what I can do with it and how it works.)
I would like to know how to find out the IP address of each computer connected to each port of the switch. Is this possible and if so how can I do this from the browser interface?
I've had been successfully using a WRT400N to extend my wireless network as follows:
The WRT400N connected to my network via an Ethernet port in my kitchen. The cable ran down to a corner of my basement connecting to Verizon router that brings in our Internet, TV etc.
The Verizon router's poor location was a problem, and placing the WRT400N in the kitchen worked perfectly, providing excellent network access and Internet to wireless devices throughout my home. It worked fine for over a year.
Recently, we had a power outage which reset the WRT400N to factory settings. and I am having trouble getting it to work again. I set it up in the first place, but am now having difficulties. Clearly, I am no guru!
I tried to get it going again by: 1) plugging the WRT400N into a PC and giving it a new IP address that would not conflict with the Verizon router (both default to 192.168.1.1) 2) turning off DHCP, 3) renaming the router, 4) changing the router password, 5) setting up a WPA2 security key.
I then plugged the WRT400N back into the kitchen Ethernet port, but something is wrong. Wireless devices cannot find the WRT400N.
The good news is that I can "see" the WRT400N through any PC on the network via a browser and access setup, but the bad news is that devices cannot see or connect to the wireless signal.
When I go to "Status" it shows the IP address, subnet address and default gateway all at 0.0.0.0. On the SETUP page, it has the correct router address (192.168.1.9), and a subnet mask of 255.255.255.0. Not sure if it is supposed to be this way...
I'm facing a problem on vWLC. I configured the vWLC and Aironet 1252, I created 2 SSID with below settings.
1. WPA2 Auth 802.1X
2. Web-Auth
Inside Wireless, I configured this AP Mode as "Local", but all of the client device such as iPhone, Laptop can't find these SSID.
Where can I find a log or list of devices that attempted to access my EA4500 wireless network?I am using the cloud services to monitor my EA4500 usage in an apartment environment.
View 1 Replies View RelatedI have ASA 5510 with CSC-SSM-10 .ASA 5510 IOS version- 8.4.2 and CSC-SSM-10 IOS version 6.6.1162.Web filtering is working fine with respective to my configuration.From yesterday morning, i was facing issue with the sites like gmail, webmail.After giving credentials like username and password in the web page, the page is not resonding.In troubleshooting process, i removed all the acls, class maps which will direct all the traffic towards the CSC. In this scenario all my mail service sites are opening.If we apply the these ACLs and Class-Maps, only my mail service sites only affecting.
View 1 Replies View RelatedI am configuring Clientless SSL VPN on ASA5505 with 8.2(2)17. After the login, default page should be "Home", but if activating "Anyconnect". it always goes to Anyconnect as a first page. If disabling "Anyconnect" using SSL VPN Customization Editor --> Portal --> Application, it always goes to the other one. Never get "Home" as a first page, can I set the first page manually?
View 3 Replies View Relatedi need to get into the web page because i need to open my XBL nat and when i type in the password to get into the routers page i get a blank screen
View 2 Replies View RelatedIn previous LMS versions the DCR could hold more devices then the licenses of the other other applications permitted and using the "user defined fields" we have used it as a general device repository for some customers, pushing only the supported cisco devices to the various applications.In LMS 4 cisco has removed all allocation possebilities from the various applications and replaced it by an all or nothing type of allocation.Does this now mean that any entry in the DCR is automatically counted as a used device license?
View 1 Replies View RelatedASA v 8.2What does the ACL hit count count ? I always thought that the acl hitcount counted the numbers of packets hitting that line in the ACL, however that is not the case. if I setup a icmp permit rule then that will only increment 1 even if I send 4 packets that hits the line. udp and tcp seems to do the same. is there some way I can make the ACL actually count the packets that hits ? where can I learn more about this ?
View 4 Replies View RelatedAny method to determine the maximum number of concurrently used SSL VPN licenses (sessions) on an ASA5540 over a period of time? For instance, over a week, the MAXIMUM number of concurrent users that were utilizing SSL licenses on the box. We are trying to determine current license capacity of the device.
We are running 8.2(5) on the ASA itself, and have 6.47 ASDM deployed.