Cisco Routers :: SRP526W - Forward Or Provide VPN Access For Clients?
Nov 10, 2011
We are having a SRP526W here which replaced a cheap, simple router. Now we would like to set up the VPN-access for outside clients again. So far this was done by forwarding PPTP (TCP 1723 and GRE) to the Windows 2000 Routing and RAS-server inside the network.According to this post the SRP521W, and therefore I suppose as well the SRP526W, are not able to forward GRE: [URL]
Is there a way to provide VPN access for outside clients with this router? Maybe with L2TP (but then we would need to forward ESP) or IPSec (ESP and AH as far as I know)?
If there is no solution we would need to replace this device again with a cheap, simple router which is able to forward GRE - as you can imagine, we would like to save Cisco from this shame.
View 3 Replies
ADVERTISEMENT
Jun 15, 2011
I have a ace board(Acsm) in my switch 6509.I need provide access for clients over https, my scenario looks like this post [URL] .But, i have only one interface, and need to configure nat for inbound clients, to access the server with ip address of the interface vlan of my ace(if i set ace gateway in a rserver, the ssl termination works). The Topology is: Client(https) -> Ace(Https) -> Ace(http) -> rserver (http). Need to configuring this nat? I need that external clients arrive at the server with the ip of the same network as him, he did not right back the packet to the default gateway, but the origin of the same network as him, so that the communication function successfully, end order.
View 1 Replies
View Related
Nov 15, 2012
i have a SRP526W and it won't boot correct, nothing is changed, I just turned it off and changed the place, now it won't boot. The POWER/SYS LED flashes and DSL Data LED is solid green!!
View 1 Replies
View Related
Aug 17, 2012
My SRP526W (running the actual firmware 1.01.27) didn't recognize my new Huawei E372 USB dongle (it's a T-Mobile web'n'walk Stick Business II, already installed the newest firmware 11.203.03.10.55).Using a Huawei E172 or a Huawei E353, both USB dongles works well. But they are slow compared to the E372. I'd really like to use the E372 stick because it's super fast with up to 42Mbps download speed.As I could read in the release notes of the SRP526W, the Huawei E372 should be supported since firmware version 1.01.26.Inside the Huawei E372 you can find the printing "Model: E372u-5", maybe this is a different model which is currently not supported by the SRP526W.
View 0 Replies
View Related
Aug 23, 2011
I've design a network with wrt54g2 router,and I'm configured with IDIRECT MODEM and its providin dhcp and it's working properly.But I want to provide static IP to my clients.
View 2 Replies
View Related
Dec 27, 2012
Is there a way to get the E4200 to NOT provide itself as a dns server to the DHCP clients? I have the unit set up to provide two dns servers to the clients, but the 4200 always provides itself as a third and it uses my cable providers dns servers. I am using a dns based filtering service to prevent certain material from being accessed within my network as the first two resolvers. So long as both or one of the provided servers is working it doesn't fall back to the unfiltered third, but I would prefer to remove it entirely.
View 8 Replies
View Related
May 4, 2011
I have a couple of ASA 5505's which work fine for what they are doing VPN and all that - we have 1 DLINK DFR-700 Firewall left and I need to get a new ASA to replace this since it is old.
All this box really does is port forward external clients to 1 address on the internal lan for client software updates. Any example configs?
So lets say we have client a with IP 1.1.1.1 and client b has 2.2.2.2 - at the moment this is what happens client a and b come in through http and get mapped to the internal http server 10.10.1.2
So I need to setup about 100 clients which can come in through http only - get mapped to the internal IP and also keeping the internal server to be able to access anything outside.
View 1 Replies
View Related
Jul 25, 2011
I have a RV082 and several of my remote laptops cannot access my server using its domain name. It can be accessed using its internal ip address. The issue is that you can log onto the server using remote access and the ip however you cannot use any shortcuts using the domain name. You can see the server with the domin name however no access path is available. This is only on a few remote user laptops. Others work perfectly.
View 1 Replies
View Related
Mar 10, 2012
When clients connect wirelessly to the WRVS4400N they successfully get a DHCP address from the Windows 2008 server. After they have the address they can no longer access the server. It cannot be pinged, no drives can be mapped and internet access fails because the same server is running DNS. The WRVS4400N is setup for DCHP relay to the server. Wired clients do not have this problem. Wireless clients that connect to a secondary WAP on the same LAN also do not experience this problem. I have updated the router to the latest firmware version, reset it to factory defaults and reconfigured from scratch. Turning the server firewall off has not made any difference either. I have been able to bypass the internet problem by adding a second external DNS server in the DHCP scope options.
View 5 Replies
View Related
Feb 1, 2011
I have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies
View Related
Sep 27, 2011
we have a ASA 5510 firewall and i have created remote vpn user who connects the internal network via vpn any connect after connecting i want him to only access his internal PC via rdp and not access other internal website or shared folders without connecting to the RDP however now he can access the internal website wihtout connecting to RDP?
View 3 Replies
View Related
Jun 8, 2011
I've got an ASA 5505 running 6.3 I've connected the management interface to our management vlan (which contains switch IPs, ilo's etc)Is there a way to allow access to this vlan from another?
View 1 Replies
View Related
Feb 26, 2012
I need to configure a network in 1 small office space that segregates 2 company domains but allows them to share an Internet connection, a WAP, a couple of printers, and a non-Cisco VoIP phone system. And, it needs to provide guest access to the internet and printers via wireless. I have a SG300-28P, an SA520W, and a WAP2000 to make it all happen. [code]
View 3 Replies
View Related
Oct 16, 2010
I set up my internet access by adsl modem as gateway, then RV042 as load balancer and dhcp server, security by MAC address restriction and static IP assignment. WAP 610N used as access point.works great for first few weeks, then somehow I can't access the network.I've been using linksys on my SOHO network, no problem before (RV042+WAP54g)
View 9 Replies
View Related
Feb 6, 2013
I've been trying to set up my new Cisco 1921 Router to provide internet access to my local network but with no success. I've been reading guides and looking at videos and I have to be missing something becaouse I can't access internet (ping/tracert) from my local network.
The DHCP server works fine and the clients on my local network gets ip-adresses from the router but can't ping or tracert outside the local network.
[code]....
View 2 Replies
View Related
Aug 26, 2012
Recently setting up a RV042G for my SOHO. Everything seems to be fine except for SSL port forwarding. I know the router's external static IP is reachable because I test it out with remote management functionality from an external IP. Port forwarding also works correctly because I have other behind the router servers in both UDP and TCP working flawlessly. PPTP VPN also works corrrectly. What I can't get it to run is an Apache server. Looks to me RV042G kind of drop all SSL or HTTP ports from the WAN side.
Configuration:
- 4 port forward rule under "Setup/forwarding" for 80/8080/443 and 8443 all to the webserver with a static IP.
- Firewall page I have Firewall, SPI, DoS enabled.
- Added a firewall rules to allow all HTTP and HTTPS traffic from WAN1 to the webserver static IP.
- Toggle Block WAN Request, HTTPS and multicast does not affect the result.
- Toggle and mapping the remote management port to other port beside 443 does not affect the result.
The same setup will works corretly under my old Netgear FVS router. Am I missing something in RV042G setup?
View 3 Replies
View Related
May 29, 2013
i go to setup/port forwarding and it has every port except port 22 available to forward. what's up with that?
View 1 Replies
View Related
Sep 17, 2011
how to forward ports using routers
View 2 Replies
View Related
Apr 2, 2011
Looking to remote access my CCTV DVR, need to port forward. Set up dyndns domain already.
View 1 Replies
View Related
Oct 14, 2012
I am new to the RV180W. I am running the most recent firmware--version 1.0.1.9.
I am having trouble getting FTP to work with my QNAP NAS.
QNAP indicates that I should forward ports 55536-56559 to my NAS. I created a custom service to accomplish this, and then, under port forwarding, I selected the service and forwarded it to the private IP that corresponds with the NAS.
However, the port forwarding configuration only allows me to specify *ONE* internal port. With other routers I have always specified the same private port *RANGE* that corresponds with the public ports that I have opened up.
View 11 Replies
View Related
Aug 28, 2011
I'm trying to setup a simple port forward in the RV 120W Router, but can't seem to get it to work.
I created a custom service called RDP for TCP port 3389-3389. I added a Port Forward to Always Allow the service RDP, from any source IP to destination IP 192.168.50.23. I have tried it with "same as incoming port" and also specified port 3389 for forward from and to.
Firewall access rule is enabled and set to Inbound, Always Allow, RDP service, Any source & destination IP, DNAT IP is 192.168.50.23.
View 7 Replies
View Related
Mar 6, 2013
I have two ports forwarded on my F7D4302 router, used for security cams, trying to add a third. The router does not open the third port. I've tried several different configuration without success. Since I've already been successful with the first two, I am puzzled.
View 2 Replies
View Related
Mar 28, 2013
I am attempting to forward port 25565 on my router, and having some trouble. I've set a static IP address as both 192.168.2.10 and 192.168.2.111, and attempted a dynamic IP address. The port forwarding page via 192.168.2.1 in the browser looks like this, with the Private IP Adress changed to whatever corresponding IP address I have set (checked with cmd /ipconfig).
After testing with multiple online port checking tools, the ports remain closed.
View 1 Replies
View Related
Dec 20, 2012
I have a customer with a Sonic wall that I want to replace with a 521.He currently has port forwaring setup so that only 3 ip addresses can access the port forward. Everyone else is dropped. Is there a way to do something similar?I can make it work for a single one via the DMZ tab with a source ip address. but there is not a way I can find to add the allow for the other two remote connections.
View 1 Replies
View Related
Oct 27, 2011
A client is thinking of putting in a srp527w. they get assigned a static ip on the adsl interface (165.228.204.x), and then have been assigned another block(203.39.183.x/29).how can i have it so that i am able to forward individual ports from the external ip's, to selected internal ip's.
View 1 Replies
View Related
Sep 25, 2012
Until now i used a D-Link router with a DDNS account on dyndns.com. I used the ddns account for accesing the surveillance camera when i wasen't at home. The ports for the cameras are 80 and 83.I have a static ip and when i tiped the IP on broswer i was able to acces the camera with port 80 and when i tiped ip:83 i was able to acces the camera with port 83.Today i got a RV180W router made de configuration (ddns, port forwarding) but now when i type the ip address i can't see the camera, instead the router interface is loading and when i tipe ip:83 i get the message "The connection has timed out".I've tryed diferent things but i can acces the camera only by internal ip (192.168.1.x) but using the DDns address i can't acces the camera.
View 3 Replies
View Related
Feb 25, 2013
We have a Cisco RV042 Router. Two ISP's and using dual wan setup. We are trying to connect to a pc on our network using rdp. The pc we are trying to connect to has been configured to listed for rdp on port 3390. I have tested it internally and connect via rdp thru said port.
I have setup a port forward rule on the router to forward port 3390 to the ip of the pc. I have setup protocol binding for port 3390 service on wan1.
View 4 Replies
View Related
Mar 25, 2013
I updated my RV180W to the latest firmware and found that port forwarding works I started using it.I've just noticed that since changing over to the RV180W, my Apacher server logs show the router's IP address instead of the remote IP address - every remote request appears to come from 192.168.0.1.
How do I get it to forward the remote IP.
View 1 Replies
View Related
Mar 11, 2013
I feel I'm having an issue, and I'm unsure why.We own a Cisco RV042 V03 with firmware 4.0.4.02-tm.
I have successfully demonstrated that I can open and forward ports 8001 & 8081 from the WAN side to a specific IP Address on the LAN side.I performed this by going to Setup --> Forwarding, then setup Port Range Forwarding & Port Triggering.
I also changed Setup --> UPnP, then UPnP Function is set to Yes.
My issue is that we would also like to forward 11101 through 11164 in the same maner. However, when I step through the same method described above, it does not seem to work.So now I am confused how I could open the 8001 & 8081 ports, but not the higher 11101 thru 11164 ports.
View 3 Replies
View Related
Oct 9, 2012
I cant work out how to get my Netgear DGN2200v3 to port forward.Portforward.com describes how to port forward for a Netgear DGN2200 but NOT for the DGN2200v3.The difference between the DGN2200 and the DGN2200v3 is that when I log into the router and go to port forwarding/port triggering there is no box to fill in the server IP address. It just says service name, service type, starting port, ending port.
View 1 Replies
View Related
Apr 1, 2013
How do I forward ports on the N600 DB F9K1102v3? I have looked through everything. When I go to port forward, I enter the info and have it all down correctly, I click save and once it reloads it isn't there and the port isn't forward.
View 1 Replies
View Related
Jul 25, 2011
I'm having a problem forwarding port 1723. What i'm trying to do is to use VPN to access my server pc and I don't want to use the VPN software that is in the router. When I telnet the port it goes through but when i try to access it outside of the office I can't get through. I've been using [URL] to check port 1723 and I get this:
Error: I could not see your service on XX.XX.XX.XX on port (1723)
Reason: Connection refused
View 4 Replies
View Related
Dec 20, 2011
I attached an Iomego Home Media network hard drive to my Linksys E3000 router (via ethernet cable). Before setting up the remote access on the Iomega, I forwarded the ports that it wanted (443 and 21) to the static IP of the Iomega. I checked to see that they were open using yougetsignal.com and they were both open. After setting up the remote access on the Iomega, the 443 port closed and I cant even get into the "manage storage device" page for the Iomega. Iomega uses TZo for the domain names. They tell me that the association is made between the name and my public IP address. My router is out of warranty since Sept, so Linksys wont give me the time of day. I contacted my ISP and while they block a couple of ports, 443 is not one of them.I've installed the latest firmware (1.0.04 - Build 6). Reset and rebooted numerous times, Port 443 remains closed.
View 8 Replies
View Related
