Cisco Routers :: WRVS4400 - WLAN Very Slow?

Nov 26, 2011

i noticed that my network speed was very slow (connected wirelessly with N) i shut down the wireless and connected to my LAN i ran LAN Speed Test

WLAN 27sec
LAN .15sec

i rebooted the router & times were <1sec, however a few minutes later it was slow again running latest firmware V2.0.2.1

View 2 Replies


ADVERTISEMENT

Cisco Routers :: RVS4000 And WRVS4400 VPN Routing

Jan 24, 2012

I'd like to simplify my setup a little bit, but unfortunately I'm not sure how to do this.
 
I have a triangle of CSB RVS devices, 2 RVS4000, 1 WRVS4400 each router has a gateway to gateway VPN with the other 2,  so from any of the 3 sites, you can access the resources on the other 2.  It also works well, that if for some reason one of the VPN legs goes down, it routes through the other router.  atleast It appears to work that way when tested.
 
I have 2 laptops that go around,  Mine and one at the office.  If either of these are off site and connect to any of the routers through the QuickVPN client.  they can only see the resources on the router they connect to. How would I be able to connect in to 1 router, and be able to access resources on the other VPN'ed routers?

View 1 Replies View Related

Cisco VPN :: WRVS4400 Finding Computers On Network

Aug 10, 2011

I have got my WRVS4400 setup and i can VPN into the network. Once in i cannot access any of the computers inside the network. I can log into the router and see that they are connected but I cannot find them in my windows network.

View 1 Replies View Related

Linksys Cable / DSL :: Slow Speed When Using LAN1 As WLAN On WAG120N

Jan 16, 2012

Recently I have changed my ISP and switched from an ADSL (4Mbps) connection to a faster fiber connection (100Mbps). I own an WAG120N which after firmware 1.00.12  (currently installed on the device is 1.00.16) should allow LAN1 to be used as WLAN. This is true and I can use it to connect to the new provider.
 
However the speed when using LAN1 as WLAN on WAG120N is very slow: download 20Mbps and upload 10Mbps. The LED on LAN1 is orange instead of green as before. I have tested the ISP connection with an WRT160NL and the speeds are much faster: download/upload 87Mbps

View 3 Replies View Related

Dell :: Inspiron 1545 / 1397 WLAN Card - Slow Internet / Frequent Disconnects?

Dec 4, 2012

Older model Inspiron 1545' using the 1397 WLAN card. Has been working fine, until perhaps the past two weeks. Now it frequently drops out, requiring manual disconnect and reconnect. Tonight Internet very slow on that laptop.

There are other devices using the same wifi (including this iPad used to post this), which connect to the wifi and Internet no issue. To me, its pointing to the laptop - either the WLAN card itself, or something in the laptop starting to fail (the laptop does have issues restarting - where it won't do that unless left for say 30 mins).

I'm suspecting a recent windows update or mcafee security update - no other software has been installed or updated.

I've tried changing antenna setting from auto to aux with no change to the above. Have checked for newer drivers - the laptop reports the version we have is the latest ( from 2009) - although they are the windows driver. Running windows 7, 64 bit - as supplied by dell when laptop was brand new. should I give up on the 1397 card and use another USB wifi adapter ?

View 3 Replies View Related

Cisco Routers :: Get RV042 V3 Run On Both WLAN Ports?

Aug 19, 2011

I've been having a lot difficulties to get Cisco RV042 v 3 run on both WLAN ports. I've tryed in Smart Backup Link and Load Balancing .... nothing.What I want to do is:
 
1 web server in LAN lets say IP 192.168.15.2
1 dns server in LAN lets say IP 192.168.15.4
 
I want to have the router running as Smart Backup Link in case one of the internet connections fails (I will say that the DNS server handles most of the domain names on the web server so it needs to be publicly available as well, and the main domain name of the web server is managed by independent DNS server somwhere in internet, so it has mechanism that can be use to change the entries let say DNS round robin way).
 
1. WLAN1 with PPPOE and WLAN2 with static ip by the second provider LAN fasion, ports forwarded to the web and the dns servers - NOT accesible. Router firmware latest version 4.
 
2. WLAN1 with static ip by the second provider LAN fashion, network normal operating but cannot access the server on port 80.

View 2 Replies View Related

Cisco Routers :: Resurrect Dead WLAN On WRVS4400N

Jul 3, 2012

After replacing my WRVS4400N Gen2 with a RV220W, I would like to know if there is a solution to resurrect the dead wlan, killed by the well known buggy firmware some time ago (I could not let it fix it in those days, cause some of use may need those devices every day, so "send it in and we fix it in some weeks" was a bad joke).

I do not need the "old" router atm, but it would be nice to have a backup device in hands, because the VPNs created by those devices are vital for my business. Is there a cheap way to fix this device, or would you say it would be cheaper to buy something else? (And after those two devices, I'm not sure that the next one would be a Cisco device again .

View 1 Replies View Related

Cisco Routers :: Configure RV042 Dual WLan / Web And DNS Server

Aug 19, 2011

I need configuring Cisco RV042 dual wlan and port forwarding for 2 servers web and dns in LAN

View 1 Replies View Related

Cisco Wireless :: Setup A 2504 To Have One Guest WLAN And One Staff WLAN?

Jun 10, 2013

I would like to setup a 2504 to have one Guest WLAN and one Staff WLAN with a controller port for each WLAN connected to different devices.
 
I would prefer to connect the WLC Guest port to an ASA 5510 and the WLC Staff port to an internal 2960S switch. Will this work? I haven't setup a 2500 series controller previously.

View 4 Replies View Related

Cisco Routers :: RV220 Host Name Resolution LAN / WLAN Stops Working?

Sep 11, 2011

I'm running a Windows Server 2008 R2 connected via cable to my RV220. The server is hosting several websites running in separate virtual machines. These websites are accessible through a reverse proxy set up on the 2008 R2. In addition the 2008 R2 provides access to storage over Windows file sharing (client backup, file sharing ...). Most of the clients are connected via wireless.My problem is that after some time (~24h) I lose the connection to the services provided by the 2008 R2 server as a result of (host) name resolution has stopped working. This only happens for wireless clients. Wired clients are not affected.To give more details: Network clients connected via wireless can't see clients connected via Ethernet and the network shares are not accessible anymore (even by putting in manually "\hostnameshare", but "\[IP address]share" still works). Being connected via Ethernet the communication between client and server works flawlessly - the server appears immediately on the network device list. The other way around is also not possible: the server can’t see clients connected via wireless. The reverse proxy is still accessible through wireless connection by putting in the IP address, e.g. "http://192.168.1.123/homepage" but "http://hostname/homepage" won't work.A restart of the router will fix things but only for the next couple of hours.

View 4 Replies View Related

Routers / Switches :: Modem And Router Won't Create Internet Using WLAN?

Nov 23, 2012

Trouble connecting to the internet wireless with Motorola SB6120 and Linksys WRT120N. The modem works directly with LAN but as soon as I try to use the router, I can connect to the network but no internet is available.

View 4 Replies View Related

Cisco Routers :: RV220W - Very Slow Wi-Fi Connection?

Aug 5, 2011

I'm an IT professional with more than 10 years experience. I have spent last 5 days trying to figure out why the wifi connection to this router is so slow, but still no luck. I'm getting only 13Mbps even if my laptop is next to the router! (wired connection worked ok)
 
I have tried all sort of setting combinations, 2.4GHz/5GHz; N only/ G,N Mixed;  Auto/20MHz bandwidth; different channels; WPA2 encrypted vs open; disable firewall; wmm enabled/disabled; 1.0.0.26/1.0.1.0 firmware... no matter what I try, I always get only 10 - 15Mbps speed.
 
Once I replace this router with my old router, it worked perfectly --- getting 70 - 80Mbps with exactly the same testing environment and configuration.
 
I really expect this router to offer much faster wireless speed according to this review: [URL]

View 12 Replies View Related

Cisco Routers :: SRP526 Slow Internet After A While?

Jan 24, 2012

Recently I placed an Cisco SRP 526W, but this modem is acting quite strange. I have configured an ADSL connection, some NAT forwardings and a VPN tunnel, all of this is working fine. When the Cisco is booted and running, everything runs smooth. Internet is working nice, I can connect over the VPN tunnel to the internal network and so on. The problem is that after a while, mostly after a day or two days, internet browsing is showing problems. IE can't display the page and I have to refresh 1 on 2 times to reach te webpage. I can't connect over the VPN tunnel to the internal network or the internal ip-address of the router, the router is not responding on ping request on the internal ip and external ip. The NAT forwardings are still responing though.
 
After a reboot everything is running fine again, but I can't let my customer reboot his router each day.
 
From the ZyXEL modem/routers we used to place at our customers I know the NAT table runs full and I had to use a greater value

View 6 Replies View Related

Cisco Routers :: Very Slow WAN Speed (RV180)?

Jan 30, 2013

My brand new RV180 seems not to be able to exceed 1.1 MB/s WAN download speed. Using a simple Linksys WRT-320N I used to have 5-6 times this speed. Value is with default settings, various sources (HTTP/NEWS downloads). Trying to improve this wit QoS-settings dows not improve this in any way.

View 2 Replies View Related

Cisco Routers :: RV215W Wireless N Is Too Slow?

Jan 6, 2013

Recently I bought RV215W router and after installing it in my home network; I started experiencing very slow internet connection over wi-fi. Wired connection to this router are working fine. After several hours of trouble shooting, I am able to isolate the slow internet issue to Wirelss N connection. Wireless b/g works fine.
 
Router is using 1.0.0.16 firmware. I tried to check is there any latest firmware upgrade for this device. Couldn't find any firmware related information in cisco web site.
 
One another point related to USB WAN; I am not using any USB for 3G connection. USB indicator is keep on blinking.

View 3 Replies View Related

Cisco Routers :: Slow Internet On Mac Using RV082?

Nov 29, 2009

I've been having trouble with the internet connection speed on my Mac. I originally noticed the problem when my mail kept timing out whenever I sent an attachment, I went to different forums trying to find the solution but nothing really worked, so I found work arounds for the email and lived with it. Recently the company I work for moved offices and I was no longer behind the RV082 and my internet ran better dispite the slower connection. Once we finished moving, I needed to use the Dual Wan Load Balance feature of th RV082 so I set it up in the new office and my internet was slow again. Unfortunatly in the new office there are several more Macs than just mine so I really need to get it working. Currently we have 2 seperate networks for PC and Mac and I really need to get them on 1. Is there a setting I may have overlooked or is it not going to work with Mac.

View 26 Replies View Related

Cisco Routers :: RV100W - Connection Is Slow / Go Down?

Dec 20, 2012

i got an issue with vpn and cisco rv100w, router is configured well and computers and iphone can connect with PPTP. Problem became when we map NAS drive from computer or we move data (1-4 Mb). Seems connection go down, speed is so slowly and drop the connection.Is it from router? or from Internet provider?
 
More data, If I connect to http of router/NAS .. all go fine, only when we need data from NAS (map drive by windows) copy, open files, ..., connection is so slowly and drop connection.
 
I saw in the logs of the router

[code]...

View 1 Replies View Related

Belkin Routers :: N1 F5D8231-4 Is Too Slow

Jan 11, 2013

Lately I notice my router is very very slow. most of the time I cannot use my ipad or it takes too long and sometimes never finishes downloading a web site. I called Belkin support, and I was told that I need to update and configure, and to do that I have to pay more than what my router cost.

View 3 Replies View Related

Cisco Routers :: EPC3825 - Very Slow Internet Using Wireless?

Aug 2, 2012

The other day I decided to upgrade my old 10/2Mbps connection to a 100/5Mbps cable connection and my ISP gave me the EPC3825 router. When using an ethernet cable everything works great and my speedchecks max out every time, the problem is that I can't have cables all over my apartment so I'd like to use wireless. With a computer located right next to the router I've gotten as high as 20Mbps and usually I'm left at about 3Mbps. I'm aware that using wireless can result in a small drop of speed but this just seems too much, especially considering the fact that I ran a steady 10Mbps when using wireless on my old connection.

Model:Cisco EPC3825
Vendor:Cisco
Hardware Revision:1.0
Bootloader Revision:2.3.0_R3
Current Software Revision:EPC3825-v302r125532-110504c
Firmware Name:epc3825-v302r125532-110504c.bin
Firmware Build Time:May 4 14:04:04 2011

View 1 Replies View Related

Cisco Routers :: RVS4000 Slow With Fiber Connection?

Jan 8, 2012

I've recently upgraded from a 512k adsl connection to a 16mb fiber optic connection.Whereas I never had a problem previously, my rvs4000 slows to a crawl once or twice per week. The only solution seems to be to cycle the power since the admin interface freezes. I also have to cycle the power on my two wireless ap to get them back up.I believe I have the latest firmware, is this a common problem on a faster connection?

View 1 Replies View Related

Cisco Routers :: Slow Internet After RV042 Firmware Upgrade?

Jan 31, 2012

After upgrading the firmware on my RV042 router to version 1.3.13.02-tm, I am experiencing very slow Internet response on most sites.  In some instances, when the page does load, it lacks many graphics.  Frequently, I also receive a "server not found"error.  In all cases, reloading the page (once it has loaded) results in a complete page display.  This is occuring on two MacBook Pros and also on an iPad.  The router is a version 1, so no further upgrades are available.  I contacted support, but since it is out of warranty, they are unwilling to assist.  Prior to the upgrade, everything worked fine, as it has for 5 years.

View 1 Replies View Related

Cisco Routers :: RV042 To RV082 Tunnel / NAT-T And Slow Performance?

Feb 18, 2013

I have an RV042 VPN tunnel with an RV082.The RV042 has a public IP Address obtained by PPPoE, the RV082 has a public IP Address obtained via Static IP.The problem I see is a really slow performance. Both internet conections are idle and the performance is about 2 or 3 kbyte/s My question are if I should I enable any of this:

- Agresive mode
- NAT Traversal
- IP Compresion
- Dead Pear Detection
 
How can I troubleshot this slow performance?

View 2 Replies View Related

Cisco Routers :: 877 - Internet Access Behind RV016 Extremely Slow

Nov 4, 2011

We are having several issues with the new batch of RV016 (rebranded as cisco and with cisco firmware.  The Cisco RV016’s are configured to load balance aDSL internet access from 4 Cisco 877 modems/routers. Ports used are WAN1, WAN2, WAN3, WAN4.
 
Issues are: WAN 1 port resets to 0.0.0.0 regularly and traffic on WAN 1 fails   DNS fails regularly behind the RV016 onlyIntermittent internet connection behind the RV016Slow internet connection behind the RV016Extremely slow DNS query and reply behind the RV016  (DNS resolve takes 1min -1m30) 

The issues above are reported from different deployment sites and with different scenarios.  
 
We also test above with Code...

View 1 Replies View Related

Routers / Switches :: Internet Connection Has Become Weak And Slow?

Nov 17, 2012

My ISP tested my connection and told me my signal is very weak. I can no longer play games online because I lag tremendously. I can't steam videos while someone else is using the internet either. Also I can't access it on wireless devices unless I am in view of the router. I'm not sure what caused my connection to suck butI have the essential plan from cox.com. When I test my connection on speedtest.com I average 75ms/ping, 3.25mbps/dwnld spd, and

View 2 Replies View Related

Belkin Routers :: Very Slow Internet Connection With N300

Feb 10, 2013

Belkin N300 - bought two weeks ago and have had very slow internet connection since.

View 1 Replies View Related

Belkin Routers :: Play F7D4402Uk Connection Slow?

Nov 21, 2012

My Router has been gone from running at bout 7Mb download speed to 500Kb download speed. When the router is restarted using the menu software it will run quicker, but only for 20-30 second then back to a slow speed. It was off while we were on holiday in August and has not been any good since. Its a shame as it only 2 years old.

View 2 Replies View Related

Belkin Routers :: Slow Internet Connection With N600

Feb 13, 2013

Having an issue with my Belkin N600 router - when initially installed it was working fine but in the past week it has gtten slower - if I connect directly to my DSL modem my speed is 1.5 MBS when I use the router connection my speed drops to .1 MBS - tried resetting to factory defaults & that did not work also tried resetting my modem *& router still having the same issue.

View 9 Replies View Related

Belkin Routers :: N150 Slow Wifi Connection

Nov 20, 2012

My N150 wireless router sees 25mb+ speed from my internet connection but my wireless connects at 1mb. Why is the WiFi being resricted?

View 2 Replies View Related

Belkin Routers :: Slow Wireless Speed With N300

Apr 23, 2013

I purchased a Belkin N-300 router, model F9K1002V4, about 6 months ago, and recently upgraded my cable internet service to a 20+ mbps level, in hopes of improving the speed of my wireless devices. The speed on all of my wireless devices (a new laptop, ipad, and iphone) is still below 1mbps, even when I'm in the same room with the router. The speed on my wired computer registers above 20mbps, so I don't think the problem lies with the cable internet. I have tried to download the firmware update on Belkin's site, but my computer says it doesn't have the right program to run it, and it can't find the program on the web. I sent an e-mail to Belkin customer service, but they just sent me an automated reply, referring me back to their website, with the firmware update that I can't access.

View 4 Replies View Related

Belkin Routers :: N600 Accessing Hdd On Usb Port Is Very Slow

Oct 19, 2012

Accessing my hdd on the usbport is very slow. Have a n600 router. Can I boost this in any way?

View 2 Replies View Related

Belkin Routers :: N600 Gives 2 Slow Green Flashes And Then Nothing Happens

Nov 18, 2012

I was having problems setting up dd-wrt so I wanted to flash back to the Belkin firmware and try again. I went to what I thought was the product page for the N600 and found the latest version of the firmware and flashed to it. The only thing it does now when I plug it in is 2 slow flashes of the green light and then nothing. I tried holding down the WPS button while plugging it in and I get the light to stay green but it doesn't respond to 192.168.2.1.\

View 6 Replies View Related

Cisco Routers :: WRVS4400N Clients That Are Farther Away Connect At A Very Slow Rate

Mar 14, 2011

I have an WRVS4400N configured as a WAN and Wireless router and can connect clients (PC's and laptops) wirelessly thru out the office. The clients that are farther away (10-15 meters and on another floor) connect at a very slow rate i.e. less than 10MBps. I have a WAP4410N configured as a repeater. Immediately after powering up it will allow connections to the 4400 and clients work fine for a 1-2 minutes, then the connections drop and I can no longer connect through the 4410. Nor can I ping the 4410 through the 4400 although right after the pwr cycle I am able to ping the 4410. After another pwr cycle the 4410 is available for another short period.I have attached some info on the configuration of the units and I also have the configuration files available.

View 4 Replies View Related

Cisco Routers :: RV220W Wireless File Transfer Slow At 2MBps?

Jul 23, 2012

I have a RV220W operating in 2.4GHz N-only mode. Channel bandwidth is set to 20MHz, channel to 6 (a site survey shows that channel as completely clear), WPA2/AES. I am connected to a TrendNet wireless bridge. The admin page for that wireless bridge shows a link quality of 100% with a signal strength of 71%. If I select a higher channel (11), the signal strength drops to 51%.
 
I have a Windows 7 PC connected to the Trendnet bridge and a Windows 7 server connected to the RV220W, both via a 1Gbps LAN port. When I transfer a file from the server to the PC or vice versa, I get a lowsy 2MBps (~20Mbps) transfer rate. That seems awfully slow. I tried channel bonding from 20 to 40 MHz

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved