Cisco Switching/Routing :: RV180W Not Allowing Internet Connection?
Mar 4, 2013
I recently saw it for a good price online, and required a new router (had a netgear that died, and my backup was a really buggy Belkin which I'm currently using).I'm having an issue with the internet, in that when I connect my ADSL modem to the WAN port it seems to work fine, however the PC can't connect to the internet. When I go into the settings it says that the WAN connection is OK and even shows my external IP. I have it set via the stardard DHCP setup.Should I have done anything specific to my ADSL modem before plugging it into the RV180W? The Modem (D-Link 320B) also has a DHCP server on it, however I assume that this causes no issues when connected to the RV180W.
View 1 Replies
ADVERTISEMENT
Mar 4, 2012
got an old computer to use from a family member and it is not alowing me to connect to the internet. it shows all my wireless connections but wont alow me to connect and use the internet. how do i fix this problem?
View 1 Replies
View Related
Sep 24, 2012
I am trying to allow RDP through my 891w.I have tried a few different yjing to no avail. [code]
View 23 Replies
View Related
Feb 8, 2013
After setting up the domain name I try to use the crypto key and it is no where to be located. Below is some of the information I copied from TeraTerm
Switch-1(config)#ip domain-name justin.lab.comSwitch-1(config)#crySwitch-1(config)#cry?% Unrecognized commandSwitch-1(config)#crypto key ?% Unrecognized commandSwitch-1(config)#crypto key ^% Invalid input detected at '^' marker.
Switch-1(config)#?Configure commands: aaa
View 6 Replies
View Related
May 8, 2013
I have a 3945 with a basic DHCP configuration applied to it. This 3945 is connected into one of the access ports of my nexus switch. I'd like to simply have the 3945 hand ip addresses out to other clients connected to the nexus switch. I have zero experience with nexus & haven't been able to turn much up through searching the net.
View 1 Replies
View Related
Mar 3, 2012
I am using 3560.IP rouitng is being turned off on this.Curious to know if I will create etherchannel or port channel.I think etherchannel.Correct me if I am wrong.On connecting switches I have vlan10,20,30 to be allowed.I am sure I need to allow these all vlan in 10,20,30 which are on the trunk port on each side switch.Post that will add channel-port lacp and make it in active mode.Is that correct.This way traffic will be load-balanced/aggregated on minimum 2 ports who are the part of this.
View 2 Replies
View Related
Feb 27, 2013
I have a Cisco 2951 Router and I am trying to set it up to use DHCP and for security purposes I need to use the "IP Access-Group in" command. The DHCP will not work when I have this command on the interface that I need to run it through, DHCP works fine when I do not have the "IP Access-Group in" command in the configuration. When I check the log after the failed DHCP attempt it shows up as denied, as if it's being blocked. The IOS I have is c2951-UNIVERSALK9-m 15.0 (1) M3. Conf Reg 0x2102.
View 6 Replies
View Related
Dec 18, 2012
i bought a cisco 2950 series switch to play around with and im trying to set it up to SSH. I have google'd a bit on how to do this and i've sort of hit a wall... i have downloaded the cryptographic image from cisco's website, installed a TFTP server (think this is where my issue lies) but when i do the copy tftp flash global command i keep getting the error accessing "xxxx" message.I have tried allowing the server through windows firewall, disabling windows firewall, allowing access through the router..
View 6 Replies
View Related
Apr 21, 2013
I got : RV180W router updated with the last firmware.Static IP for the DMZ host (Synology Server 212+) My problem is that I had try all combinaison since 10 days to get IP source in synology interface (to block IP's of bad connections...) but, I only see the RV180W adress....So impossible to block bad connections IP.
View 3 Replies
View Related
Dec 15, 2012
I would like to ask if what is the difference between RV180W-E-K9-G5 and RV180W-A-K9-NA specifically the -E and the -A. As far as I know -A is the compliance code for Philippines. Am I right? If yes, what about -E? There is a documentation for wireless complaince on Aeronet devices but what about these SB products?
View 9 Replies
View Related
Feb 5, 2013
I'm trying to make the VPN connection between two routers CISCO RV180w.I performed the basic configuration in cisco "server". I did the same in cisco "client".The following configuration and logs, do not know what to do ...
SERVER CONFIGURATION:
IKE Policy Configuration:
VPN Policy Configuration:
CLIENT CONFIGURATION:
[code]....
View 8 Replies
View Related
Aug 25, 2011
We have a cisco 2800 router and are now required to allow users to be able to connect to another company's extranet. Having tried this it wont allow this connection so I have added this to the access-list 101
access-list 101 remark SDM_ACL Category=0
access-list 101 permit ip any host 192.168.0.246
access-list 101 permit ip any host 192.168.0.247
[Code].....
I dont think the gre is being allowed back in. I have attached a cut down copy of the config. I have just general experience of cisco routers and not cisco qualified.
View 2 Replies
View Related
Jan 29, 2012
We have a new internet connection from DSL cisco router 800 Series (877).
You has been delivered it to us with Cisco Router 800 series (Ver 877), when we connect it to the PC directly it’ll work fine with the static IP.
We configured the OSPF between the Switch and the Router. and we can reach to the DSL router IP from our LAN any where. but we can't exit from the router to the internet.
DSL router 877 ---------------> Core Switch 6509 ----> PC
Router 877 (DSL):
-----------------
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code]....
View 5 Replies
View Related
Feb 18, 2013
I am working with a RV180w and need to map drives from the internal network to the VPN client but whenever I try to connect to a shared drive I continue to get authentication messages from the DC. Any useful guide for configuration in this scenario. Internal subnet is on Windows 2008 domain.
View 1 Replies
View Related
Jan 10, 2013
I've read and read about setting up the WAN static IP connection, and can't get it to work. I purchased this router to replace an older Linksys Router (WRT150N) so that I could better implement VPN. All I need is 2 remote connections. The Linksys Router has been working great with a static IP setting, so I figured all I need to do to is enter the same IP, subnet, gateway, and DNS settings in the RV180W and it should work fine. Well it doesn't provide any connection to the internet. As far as I can see, it has all the same settings set that the linksys has.
Is there something additional I must do for a WAN static IP setting setup. I even contacted the ISP but they say their modem is fine and of-course they won't assist with the router. As soon as I connect the linksys back to the modem, I get access to the internet.
I'm no engineer, but something isn't allowing any Internet services. LAN is fine. I attached a W7 laptop to the router, and it says it can't reach the internet due to something about proxy services. There is no proxy server so not sure what it is referring to.
By the way I tried another manufacturer router just to ensure that it wasn't a defective RV180W, but that router didn't connect either - same issue. If I set it up on my home service, both work albeit only with DHCP WAN settings.
View 9 Replies
View Related
Jan 2, 2013
I have a problem with my switch. The model no. of the switch is as follows:
Linksys SRW2048 10/100/1000 48 Ports
Serial No: RJT00GC00395 GGR2906 MM
1. I am creating a home computer lab. I do have 3 servers HP ProLiant DL 385 G1. Two of them have 6 gigabit ports where as the third server has 2 gigabit ports.
2. Installed ESXi 5.1 on two servers where as installed FreeNAS on the third server and configured it as iSCSI storage and NFS storage.
Problem:
1. Every port works perfectly fine. However, when I keep connecting the ports of the switch to the ports of servers, internet gets disconnected.
2. Interestingly, my wireless internet also gets disconnected, the ports of the switch does not have any internet now.
3. This happens till I connect above 8-9 ports of the switch to the servers.
3. However, when I remove the connection between the switch and the servers, internet comes, wireless internet starts working; and the port of the switch also gets internet connection when I check the internet connection of the individual ports one at a time.
Some more information:i do have internet service provided by Time Warner Cable. My internet speed is as follows:
Download Speed: Up to 15 Mbps
Upload Speed: Up to 1 Mbps
I do have a modem *** router by Motorola which has 4 gigabit ports.Model no: Motorola SURFboard SBG6580 i am assuming it is some thing related to bandwidth of the internet.
View 4 Replies
View Related
Sep 25, 2012
Until now i used a D-Link router with a DDNS account on dyndns.com. I used the ddns account for accesing the surveillance camera when i wasen't at home. The ports for the cameras are 80 and 83.I have a static ip and when i tiped the IP on broswer i was able to acces the camera with port 80 and when i tiped ip:83 i was able to acces the camera with port 83.Today i got a RV180W router made de configuration (ddns, port forwarding) but now when i type the ip address i can't see the camera, instead the router interface is loading and when i tipe ip:83 i get the message "The connection has timed out".I've tryed diferent things but i can acces the camera only by internal ip (192.168.1.x) but using the DDns address i can't acces the camera.
View 3 Replies
View Related
Nov 8, 2011
I have a Cisco 1811W that after several years in service suddenly stopped allowing any wireless connection to laptops on the domain. It allows hard wired connections and devices that are just using the wireless hot spot like iPads and Iphones but not devices on the domain. These same laptops connect wirelessly without issue at our other facilities which use the same hardware.
Here is the config file of the router in question...
router#show run
Building configuration...
Current configuration : 11776 bytes
[Code].....
View 2 Replies
View Related
Jan 15, 2013
is it possible to configure a Cisco 881 router to split the incoming internet connection between two ASA's? If one ASA fails then the router would switch traffic over to the second ASA. The 2nd ASA would takeover from the primary ASA through the active/standby failover configuration and crossover cable. I'm trying to avoid configuring the switch to control the traffic using VLANS if possible.
View 3 Replies
View Related
Mar 19, 2012
we using Linksys router for Internet for different vlans now we take 3750 as core switch for another different vlans 10,20 we create v Lans 20,20 also create cpd servers and we need Internet for vlans 10,20 through linksys router how should we configure?
View 5 Replies
View Related
Nov 12, 2012
I have been reading for awhile now on all the Cisco forums on the 3560 and shaping egress traffic but I wanted to verify my thoughts on this. I have 3560 that connects to the ISP that is policing at 10Megs, I want to shape my egress traffic going to the ISP, I do not want to provided QOS to any specific traffic type but only shape all traffic outbound. Will my config below shape "all" egress traffic going to the ISP on the 3560, on a port that is physically connect at 100Meg Full duplex?
int gi0/1
srr-queue bandwidth shape 40 40 40 40
I gathered these numbers using the formula of 100* 1/weight, which would equal 2.5 and if each queue has 2.5 meg that would = 10Meg. However another concern is that I don't think I have the full 100Meg on the interface to use (correct?)
View 3 Replies
View Related
Jan 25, 2012
i'm already has one internet connection is conecting directily to the Core Switch 6509, and the Switch is route any internet request with default route:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.170.10.10
10.170.10.10 is --> Next hop for the DSL router internal IP, and it's working fine.
We have a new internet connection with another ISP/ with another DSL router, how to connect both of them to exit from the Core Switch 6509.
is it ok if i make another default route to the Next hop to the new DSL router as:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.80.10.10
10.80.10.10 is --> Next hop for the new DSL router internal IP.
View 6 Replies
View Related
Jul 15, 2012
I've got an 1841 router acting as the firewall for a LAN. It also does NAT and acts as the dialer for a PPPoE DSL line to the internet.
All is working fine, except now I need to allow a Tivo device to connect to certain ports on the Tivo servers on the internet. I want only the Tivo to be able to do this. The problem is that NAT is happening before my outbound ACL is checked, so even though I've got rules to allow the Tivo's LAN address out on all ports, it never works. I've verified this using a syslog server, and can see my external DSL IP trying to connect to the Tivo servers and being denied.
I've done things like this at work by NATting the appropriate internal host to its own external static IP address, which allows me to write rules allowing only that external address to do stuff. But I don't have multiple external addresses to work with here.
I tried applying my outbound ACL to the LAN interface of the router in the "in" direction (and removing the same ACL from the Dialer interface in the "out" direction), but that broke other things like the router's own ability to ping out to the LAN or to see a TFTP server on the LAN. I could maybe fix all of that with rule changes and inspect statements on traffic going out toward the LAN (not sure of this, think so), but I'm wondering:
Is there a better way to let just the Tivo makes outgoing connections to certain ports?
Config pasted below:
!
! Last configuration change at 17:15:10 CDT Sun Jul 15 2012
! NVRAM config last updated at 16:27:14 CDT Sun Jul 15 2012 by someguy
!
[Code].....
View 3 Replies
View Related
Jan 14, 2012
I just bought the 655, mainly for school/Xbox. My parents use it also, but I bought it for myself mainly (shh). I set it up correctly and got connected, but suddenly I wasn't allowed Internet access. The router connects to my laptop, but won't get Internet access. I called customer service and he didn't know what to do. We tried everything he knew and nothing worked. I don't want to return the router cause I read it was very good, but I need internet for school. I have Rev. A and F/W 2.00.
View 8 Replies
View Related
Aug 10, 2012
RV180W wired lan has no access to internet. VLAN is disabled ja router get ISP IP and DNS without any problems. PC ping respond DNS name query OK but web browser can not open or show pages (time out error). All router traffic between wired and wireless network the works just fine. Wireless network web traffic works without any problems. Router firmware is lates 1.0.1.9
View 2 Replies
View Related
Jan 8, 2012
I'm a college student working on a lab involving a Cisco PIX 501 Firewall.
My project involves 1 computer and a firewall. My goal is to use the firewall to allow access to the internet for that computer which uses a static IP 192.168.1.5 and ONLY for that IP address. The firewall is connected to the internet.
I have the computer hooked up to the firewall with the serial and using hyper terminal to enter commands. I think I need to use access lists in order to deny traffic on those ports for those particular hosts. I can't figure out exactly how I need to set it up.
What I need to do is permit internet access for 192.168.1.5 alone. Any other IP should not be able to access the internet.
I tried:
access-list 1 permit tcp host 192.168.1.5 any eq 80
access-group 1 in interface inside
I cannot access the internet using the computer with 192.168.1.5. The goal is to be able to access with that IP and no other.
View 6 Replies
View Related
Mar 6, 2013
We have the RV180W router and the WAP321 access point in our business. We want to broadcast two SSIDs from both locations: the office SSID, which shares routing to LAN traffic, and a guest SSID.The office computers are attached via ethernet to a switch off of LAN port 1 on the router. The AP is attached to LAN port 2 on the router.On the router, the office SSID and the LAN are members of VLAN 1. The guest network is a member of VLAN 2. From the router, everything works just fine.On the WAP, the staff SSID works fine, but the guest SSID has no internet. Both the office and guest networks get DHCP successfully from the router.Our VLAN membership table in the router and WAP are attached, as well as other configuration details.Why would we not be getting internet on the guest ID only on the WAP?
View 8 Replies
View Related
Nov 3, 2012
My Netgear wireless router had been working just fine and then inexplicably stopped allowing wireless internet access. My modem is fine. I contacted my internet service provider, and no luck. I unplugged the router's power source and plugged it back it in. Still not working. I switched the power on and off. Nothing. I do not know what to try next.
View 1 Replies
View Related
Nov 16, 2012
Belkin N450 Router. I want to restrict Internet access completely but allow LAN access to a shared drive for a particular computer on my wireless network. I have gone into the web based set up page and under access controls have enabled and added this computer to the list. I have blocked http, https, ftp and nntp. I don't know if this is enough. The reason I am asking is that I am in Iraq right now and I want to allow my fellow team members access to the wireless for using viber on their iphones but one cat even though he has hardwired internet wants to continuously suck off my wireless for his computer to download stuff since I paid for faster internet. I am trying to do this quietly and still allow him access to the shared drives on the LAN. Sooooo If I block him just outright will he still have access to the drives or do I need to pick and choose like I did above and if I need to pick and choose did I miss anything other then pop3 email and imap?
View 2 Replies
View Related
Mar 20, 2011
The following diagram represents my current network.
I would like for the Phone and the Laptop both on wireless to have internet access but not access to the other PCs/shares.
I have access to routing tables in both the cable router 10.0.0.1 and the wireless router
wired : ASUS RX3042H
wireless : Linksys WRT54G (default Firmware)
View 2 Replies
View Related
Oct 16, 2011
I have a 100mb conection and regularly get 90mb plus speed when conected direct to the modem. If I conect via the E4200 I only get 50mb ? I have tried disabling the firewall and QOS but this has had no effect. I am using a wired conection and the latest firmware. Its almost as the E4200 is capped at 50mb throughput.
View 6 Replies
View Related
Apr 14, 2013
Installed new N600 router and every box in the house can access the internet - except for my Vista powered laptop. My network shows up as Unidentified network with 'locla only' access. Ben scouring message boards all day. Can't find a solution at Microsoft.
View 3 Replies
View Related
Oct 29, 2011
I have a Linksys router (model BEFSR41) and I all the outputs going to two computers and two gaming systems (X360 and PS3). I have had the router for over a year and it works fine, but I recently decided to attempt to have my 360 access the media on my computer by linking the two together through the Media Center. To do this, I needed to enable my router to allow UPnP (according to Microsoft help). When I did enable this, the router would disconnect me every 2-5 seconds from the internet, then would reconnect me right away.I have no clue why it was doing this (it occured across all of my devices) so I just disabled UPnP and things went back to normal. How to fix this so that I can have a consistent and stable connection when I have UPnP enabled?
View 1 Replies
View Related
