Cisco VPN :: ASA 5510 - Can't Install CSD Image
Jun 12, 2013
I'm facing the problem that I can't install an CSD Image on the asa. Got the error:
[OK] webvpn
webvpn
[ERROR] csd image disk0:/csd_3.6.181-k9.pkg
The disk is (or was) full during extraction.
ASA 5510 has 256MB RAM, 1024MB Flash, ASA Version 8.2(5)41, ASDM 7.1(3)
View 1 Replies
ADVERTISEMENT
Aug 28, 2011
I have a pix 515, time to time the firewall start rebooting with invalid flash error I found erasedisk.bin in internet, after that i cant load pix532.bin ios file and others pix***.bin are not workingThe only file i am able to load is pix508.bin it,s start asking me activatin number before install I have a previous activation number ios version 5.3.2 but this number is not correct.
View 1 Replies
View Related
Dec 8, 2011
I am in vain trying to transfer image to my asa5505, but fails in last step copying the file to flash:
Boots to rommon
tftpdnld image -> asa5505 boots on tftp file in en mode, i try to copy command but this fails, always getting No such device error. I have tried all different solutions found on google for this step, but it simply does not work, as i am never able to ping anything from the ASA.
rommon #6> tftpdnld
ROMMON Variable Settings:
ADDRESS=192.168.1.115
SERVER=192.168.1.113
GATEWAY=192.168.1.254
PORT=Ethernet0/0
VLAN=untagged
IMAGE=asa805-k8.bin
CONFIG=
LINKTIMEOUT=20
PKTTIMEOUT=4
RETRY=20
tftp asa805-k8.bin@192.168.1.113 via 192.168.1.254
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
ciscoasa# copy tftp disk0:
Address or name of remote host []? 192.168.1.113
Source filename []? asa805-k8.bin
Destination filename [asa805-k8.bin]?
Accessing tftp://192.168.1.113/asa805-k8.bin...
%Error opening tftp://192.168.1.113/asa805-k8.bin (No such device)
Apparently it dont work with Eth, nor with vlan 1. Any way to shut down all functions in router so i can access everything?
View 2 Replies
View Related
Mar 17, 2012
I downloaded a new image to my ASA 5510 and found out up on reboot that the ASA doesn't have enough memory so I am booting to the "ciscoasa" prompt with no config. I still have my old image in disk0:. How do I roll back to this old image?
View 1 Replies
View Related
Feb 9, 2012
I'm have upgraded our ASA5510's from 7.0.8 to 8.4.3 and now I just need to do the ASDM, but get this error? The bin file has been uploaded: [code] Device Manager image set, but not a valid image file disk0:/asdm-647.bin.
View 3 Replies
View Related
Oct 10, 2011
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies
View Related
Jan 7, 2013
Have anybody direct link to download IDS image for GNS3 ?
View 1 Replies
View Related
Sep 4, 2011
I want the below mentioned IOS image for backup purpose. But I am not finding it in cisco.com or anywhere in the in internet. where can I get this version of image other than my router.
c2800nm-advsecurityk9-mz.124-3d.bin
View 1 Replies
View Related
Apr 30, 2012
I get an IOS image for GNS3? I dont work in a company that would do that for me
View 4 Replies
View Related
Oct 19, 2012
any 3725 IOS image that supports the ip sla command? I tried searching for it using the feature navigator but i received something like "15T" and I'm not too sure what that is.
View 4 Replies
View Related
Apr 2, 2012
How do I tell if my cisco 2960 has the Lan Base or Lan Lite image?
View 11 Replies
View Related
May 8, 2012
I successfully converted an old 1231G to CAPWAPP. However, when I try to join it to a WLC5508 I receive the floowing errors. [code]
View 2 Replies
View Related
Dec 30, 2011
i upgrade the IOS for switch c2960 and the swtich do not boot from the new image.
-show version
-show boot
-show flash
View 6 Replies
View Related
Feb 18, 2011
I`m having problem with booting Cisco router 2610 and I`m having this message :
C2600 platform with 131072 Kbytes of main memory
Program load complete, entry point: 0x80008000, size 0x439138
Self decompressing the image :####################################################################################################################################################################[OK]
After that, I can't type any thing?
View 3 Replies
View Related
Aug 4, 2011
i have an ASA 5510. it was running asa708-k8.bin and i have attempted to install asa821-k8.bin. i have done this on many ASAs before effortlessly.this time i have had an issue. the ASA will not load the new image, and for some reason will not even load the old.the ASA seems to just keep crashing. i have erased disk0 (advised in forum): and attempted to load the image from tftp. please see below. i know i need to re-formaet the flash, but cannot get into the ASA at all to complete this. [code]
View 2 Replies
View Related
Mar 29, 2011
I got a PIX 501 off ebay and im trying to upgrade it to have an ASDM image on it.Ive downloaded every copy of the ASDM image i can get my hands on, and when i transfer it to the PIX when its up and running i get out of memory, If i do it through monitor mode, i get the error "bad magic number" no matter what i transfer to itI can transfer a new image to the PIX (a non asdm one through monitor mode.
View 3 Replies
View Related
Dec 26, 2012
i installed Prime LMS 4.2 on Vmware ESXİ 5.0 and then in console screen i create hostname,IP,DNS etc correctly.Then, in LMS 4.2 console screen and another client Win7 PC can ping each other however i cant reach LMS 4.2 via web browser remote client PC.
View 3 Replies
View Related
Mar 28, 2011
I am attempting to upgrade my 1261n's to lightweight but the upgrade tool (3.4) is telling me that it is not compatible with this model AP. Is there an article or quick run down on what I need to do to upgrade these AP's?
View 2 Replies
View Related
Mar 29, 2012
My site got the NAC-3315 appliance and we would like to reimage this appliance to inline posture mode (for VPN purpose)What's the proper migration process should deal with this? Is the NAC-3315 hardware comply with the Inline posture mode requirement?
View 4 Replies
View Related
Oct 22, 2012
I struggle with how to install an IOS into an AP. And I am still not very clear on how this is to be accomplished. I have an 881W and have downloaded what I believe to be the latest IOS for this AP (ap801-k9w7-tar.152-2.JA). Problem is that I have not really found a good or at least clear set of instructions in how to load this IOS into my AP, so I have not done that yet.Does the IOS that is currently installed into the AP remain after an update or does the new IOS overwrite the current IOS. And how does one recover from a, heaven forbid, faulty installation. What is the fallback from that. How I can update my AP. Because, right now, I am most certainly hesitant to even attempt an upgrade.
View 4 Replies
View Related
Jun 8, 2011
I have a problem with LMS s/w backup procedure. It outputs the following error: SWIM0036: Could not add this image to software repository.
View 8 Replies
View Related
Nov 12, 2011
My customer has purchased the standard Cisco 881 (Data) ISR router and now requires (Voice) CUBE services for the support of IP-IP gateway SIP services. I noticed there is multiple models for the Cisco 881 such as the SEC/3G & SRST. Any way to change the Universal image from Data to Voice to support CUBE if possible. Just want to try and eliminate purchasing new Cisco 881 with Universal image for Voice.
View 4 Replies
View Related
Nov 3, 2012
i have cisco 1260 Access point with standalone ios ap3g1-k9w7-tar.124-23c. i download new IOS to connect the AP to the controller the new ios is ap3g1-k9w8-tar.124-23c.JA5.tar. upgrade th AP to LAP. is it just install ios like in router & switch by tftp?
View 1 Replies
View Related
Nov 29, 2012
I am trying to TFTP an image to a Cisco 2504 WLC. The management interface is 10.1.1.1 /24 and I have my PC connected to a port on the WLC with the IP address 10.1.1.10. However, I still do not have connectivity between the PC and WLC.
View 3 Replies
View Related
Jul 5, 2011
Got a question regarding 2921 modules. Can I use VWIC2-2MFT-T1/E1 along with NM-HDV2-2T1/E1 on 2921 and what is the minimum requirements for IOS image?
As I understand, NM-HDV2-2T1/E1 is supported on 2921, however VWIC2-2MFT-T1/E1 is not, VWIC-2MFT-T1/E1 only. But VWIC-2MFT-T1/E1 is not supported on 2921.
View 4 Replies
View Related
Aug 23, 2011
I've a problem with a router 2811:
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
[Code]......
View 14 Replies
View Related
Dec 22, 2012
I purchased a used AIR BR1310G-A--K9-R from a local high school that was rebuilding their athletic field. The AP was used for communications for their pressbox staff. The AIR BR1310G was part of the schools campus wide WiFi network and was upgraded to an lwapp image c1310-k9w8-m 12.4 3c JA. Our home sits on a large lot and I would like to convert the BR1310G back to an autonomous AP.
In order convert it back to an automonous AP, I will need the original image. The school used a contractor for their WiFi network and they do not have a backup of the original image. I do not have a service account with Cisco so downloading the autonomous image from the Cisco website is out. What are my options for either obtaining an image file or using the current managed image without a WLC?
View 0 Replies
View Related
Feb 27, 2012
I wanna upload ios image of 36mb on a 2801 but I get error not available space. The router already has ios image of 40mb and available space is around 15mb. How to delete existing image and upload the new image?
View 7 Replies
View Related
Feb 13, 2013
I have a couple 1130AG switches. I'm trying to pull an image file from the flash on a Cisco Air AP1131AG. The file is c1130-k9w8-mx.124-23c.JA4.tar. The issue that I'm seeing is, I do not see a copy command to go through the tftp process. I've tried to use tftpd32 and enter the IP of the AP as the remote host, but that is not working either. Do I need to connect an ethernet cable straight to the AP in order to use Tftpd32, or can I use a console cable?
View 9 Replies
View Related
Jun 23, 2011
I have a PIX 501 and I am looking to download an OS as my current image is corrupt and the PIX will not boot. Where I can download the O/S from so I can tftp it across to the router.
View 1 Replies
View Related
Aug 28, 2011
I just bought a used PIX515e. It is running version 8.0(3) and ASDM 6.1.5 Because I do not know the history of the unit, how can I tell if the image used came from cisco and not some download site? I guess I should've thought about this before buying it but hindsight is...you know. Worse case is that the person who had it before me dl the software that was infected with a backdoor or something else. I don't have a service contract so I'm kinda stuck.
Can I download the image from the firewall flash and compare a MD5SUM?
View 12 Replies
View Related
Aug 23, 2011
I installed LMS 4.0 succesfully, but when i go to topology, can view all network, but the "AswitchA" Core 4507R+E be displayed as "?"
And it can not display this "AswitchA" into CISCO VIEW, display this messaje :
"Cannot find applicable device package for ... This error could be due to one of the following:
- The device package for this device type is not installed.
- Device support for this device type is not available.
- You are trying to open a component inside a device.
To correct the problem, either install a device package for the device type, or open the parent device to manage the component."
View 2 Replies
View Related
Apr 29, 2012
We deploy 881G routers at our store locations and are planning to upgrade the IOS to 15.2.2. One concern we have is if the router fails to boot to the new image. Is there a way to configure a second boot image as a failover in case the primary boot image does not load? Our current DR plan is to have a laptop on site that we can connect to remotely and setup a console session to manually change the boot file. This can be cumbersome and time consuming, so I'm wondering if the 881 has the ability to have another file loaded if the boot fails.
View 4 Replies
View Related