we have replaced a PSU in an ASA 5585 and after it, when we want to see the new PSU serial number, strangely appears the old one instead of the new one. Do we have to do anything in order to get the inventory updated?
View 4 Replies
I have an ASA 5585 in transparent mode, multi-context. It seems that the option to configure a BVI in one of the traffic contexts isn't there. In other words, while I see the option to configure a bridge group interface in the admin context, no such option comes up in the traffic context.
[CODE]....
I have had my DIR-655 for a few years now and it has been running fine up until a few months ago.
I haven't changed any features or done some major changes but it started cutting out all network traffic. WiFi drops internet connection but is still connected and both my NAS and my wired computer are also cut off from the network but shows as connected.
The router GUI is not accessible when this happens. The routers leds are lit but for some reason all network activity is dropped. Restarting the router resets everything.
This is rather sporadic but happens at least 2 times a day.
I have disconnected the internet connection and left the "internal" network be up and running and then too I get the network "cut-off" after some time so it is not dependent on my ISP.
I have Hardware Version A2 and am running Firmware Version 1.32NA. I tried to install the 1.35NA and it goes and does something but when it comes back it is still on 1.32NA so the FW upgrade doesn't kick in. Is my hardware too old for it possibly?
i've upgraded our WLC 5508 from 7.0.220 to 7.2.115.1.For our guest WLAN we use web authentication with customized startpage, no login error page and no logout page. The customized login page is displayed correctly. After successful authentication the browser is forwarded to the default CISCO login page "login.html". No further autentication is possible, also no internet access.Reload the customized webauth bundle to the controller didn't change anything. Is there a change in the HTML/Java code of this controller version? I didn't find any hint in the release notes. Or do I need the newer web authentication bundle with version 1.0.2?
View 6 Replies View RelatedAlright it said to click "Check for updates" and then go back to download the update but everytime I click "check for updates" it says I don't have an internet connection even though I can still connect to the itunes store and everything. ran diagnostic in itunes and it told me to enable my network interface and I did that but it still wont work! My Internet signal is brilliant but I can't download the upgrade unless I update the software or something but it won't let me unless i have an internet connection which I do.
View 2 Replies View RelatedThe latest driver is version 3.2.7 for Windows 7. I am still on the 3.0.2.0 driver which works fine for me. I just wanted to note that the 3.2.7 driver obtained from Windows Update doesn't work well, drops connections and takes longer to establish a connection. I've tried to update twice and each time I go back to the older driver.Can someone at Linksys examine the performance of this driver?
View 9 Replies View RelatedI made a big mistake and updated my EA6500 with the wrong firmware.I selected "ver.1.1.38.149770" which I shouldn't have done since it's for the the EA6700 which i read aftwerwards....how stupid can one be Anyway, the device is not started up as it should.I'm able to use it as a cabled router but it's not sending out any wireless signal and the led light is blinking.A factory reset obviously didn't work since the firmware was wrong.So, my question is if it's possible to revert to an older firmware using the USB port?Or for example push a firmware using an ADB command if it's possible to connect using a cable?Or in some other way?
View 4 Replies View RelatedI've been trying to port forward my WRT54G2 router.I've tried to update the Firmware, use another computer or another browser.But it still doesn't work!
View 1 Replies View RelatedI can't inventory a 4507R + E / SUP7E Version 15.1.1 SG with the last version of LMS 4.2.1. Next, the extract of IC_Server.log.
[code]....
We have several unknown devices within our inventory. When running an inventory report the message I get back is "No Credentials available".
For inventory checks is it just SNMP that is used or is it the standard credentials that are needed ?
I am planning to edit the credentials for the single device manually to see if this makes a difference. Our integration is with ACS and we have a machine account with admin priveleges.
Device Verification for the device states "Device Not reachable" for SNMP and SSH. There are no drops on any of our firewalls but snmpwalk does work from the command prompt from the LMS server.
Are there any further checks I can make for these 2 messages:
* "No Credentials available". * "Device Not reachable"
I have been having problems getting devices into DFM once I enable fault management.I am now having issues with the basic LMS / RME I am getting the following issue:"No Device exists in LMS or Inventory is not collected for devices."I experienced this before and resolved by reapplying the licence.The issue has gone from - all devices discovered and added to LMS and DCR ok turned on Layer 2 Topology and Faults and then no devices appearing in DFM.after restarting the Daemon manger I have no devices in LMS. total device approx 1900 - standalone setup.
View 5 Replies View RelatedAfter I upgrading all device packages, inventory collection failure to complete. All devices stuck on pending state and at the end of the job all devices are under not attempted and job result description ses " Timed out. Make shure that ICServer is running". I made sure that ICServer is running.
LMS runs on windows 2008 R2 server
I have Cisco Works LMS 4.0 on Win 2K8 64 bits on VMware EXs. I am facing issue with reference to Inventory Collection, my 10% devices (including Routers & Switches) Inventory collection is failed and give me error (Device sensed, but collection failed). I increase the SNMP timeout 10 sec, 30 sec, 60 sec and even 100 sec the result be the same.
View 1 Replies View RelatedA customer of mine have 2 VSS systems for wich IC times out during collection when trying to read from flash on them. From the ICserver.log
[ Thu Dec 13 16:45:19 CET 2012 ],WARN ,[Thread-20],com.cisco.nm.rmeng.util.logger.XDILogger,67,com.cisco.nm.xms.xdi.pkgs.SharedInventoryCatIOS.FlashAGI_CISCO_FLASH_Mib,g$eval,70,com.cisco.nm.xms.xdi.pkgs.S
[Code].....
LMS 4.0.1 installed on Windows Server 2008 R2 Standard with SP1. Created Inventory collection job, but couple of hours later, it is failed with all devices Not Attempted. Increased SNMP timeout on 10 sec, started again for only 1 device - collection failed again. I am attaching pdshow and ICServer file.
View 6 Replies View RelatedThere are 3 newly installed Cat4506-E.SSH and SNMPv3 access are verificated. Devices are managable in every way only the inventory is missing.If I try to collect manually then they fail but I can't figure it out why.
View 2 Replies View RelatedWe have LMS4.0 monitoring 100+ devices. In that collection we have 2 4506e switches. The switches are identical,but one is inventoried successfully and the other always fails.Both have verified their credentials. The 4506e failing inventory is the only device not being inventoried.I looked at other post and increased snmp timeout with no effect.
View 1 Replies View RelatedWe have 694 units Cisco Catalyst 4507R plus E swithes accross the network. LMS 4.1 can discover it no problem however, i cannot extract inventory information for these switches. I get the this "Number of devices that do not have inventory collected data" on the report.installed System image file is "bootflash:cat4500e-entservicesk9-mz.150-2.SG1.bin"
i saw this supported version:
150-1.XO (or) 03.01.00.SG <<--- should i have the exact image or higher version will do? [Inventory Config and Image Management]
Reference: [URL]
Is the image installed on my switches not supported? seems like I have higher version.
I have an LMS 4.0.1 server (on Windows 2008 R2) with all the LMS and device updates applied that fails when trying to do an Inventory Collection on a Cisco 3925E router. The router is running IOS Version 15.1(1)T2. This device is apparently supported according to:
[URL]
Some 'show ver' info:
Cisco IOS Software, C3900e Software (C3900e-UNIVERSALK9-M), Version 15.1(1)T2, RELEASE SOFTWARE (fc1)
ROM: System Bootstrap, Version 15.1(1r)T2, RELEASE SOFTWARE (fc1)
System image file is "flash0:c3900e-universalk9-mz.SPA.151-1.T2.bin"
Cisco CISCO3925-CHASSIS (revision 1.0) with C3900-SPE200/K9 with 689152K/293888K bytes of memory.
'show inv':
NAME: "CISCO3925-CHASSIS", DESCR: "CISCO3925-CHASSIS"
PID: CISCO3925-CHASSIS , VID: V02, SN: FGL152610R8
[Code]....
We have just installed lms 4.2 and are having problems collecting config and inventory from ws-svc-wism2-k9. The response from TAC was that this is not supported. And it also says this in
[URL]
Is this really the case ? Will there be released packeges to support this. It would be really useful if this was supported in lms4.2.
I was trying to add a 2504 to PI, but I keep coming up with this error in Unknown Devices: Collection Status : Unexpected error. [code]
View 4 Replies View RelatedI reinstalled CiscoWorks LMS (Windows 2008 R2) updated th LMS with all availible devicepackages and imported all devices with a xml bulk import of the former installation. Now I am frustrated.... because after the reinstallation LMS has problems collecting the inventory data.The inventory collection for one local device (Cisco WS-C3560-8PC-S) starts and nevers stops.... I have to stop the ICserver to stop the inventory collection.
I have only 4 of nearly 1800 devices where it was possible to collect the inventory information.All the rest is supposed to unreacheable...Reports> Inventory>Management Status>Unreachable Devices.But if I take one of the devices which is reported to be unreacheable and do a device diagnostic (Monitor> Troubleshooting Tools> Troubleshooting Workflows) says it is reacheable...
The inventory does not appear in the "Collector Status"?
By reruning discovery with new seeds etc I have more devices discovered. Howeverr they are not shown in the inventory, only in the Device Discovery Summary however.
View 10 Replies View RelatedI'm looking for Inventory Management tool to take complete details of all IT Assets over network.
View 1 Replies View RelatedDoes the 5585X supports BGP ? What if someone wants to use Antivirus + IPS feature in that . I have seen IPS modules for 5585X but looks like the antivirus module is not avaliable for 5585X
View 1 Replies View RelatedI added this wlc in lms and tried to collect inventory. But it is failing after taking long hours.(LMS Version 3.2.1,WLC 4404 -Version 7.0.116)(SNMP walk is successful & using SNMP V2c)I hope the specific package is available in LMS as i could find the WLC 4404 in Device update->Sys Obj ID -> <id of 4404 WLC> Any bug could be the reson for this...?
View 6 Replies View RelatedCreating several Inventory-Report Templates via Report Designer I was asking myself how to export/import these templates for use on other systems, performing backup.
View 1 Replies View RelatedInventory in CiscoWorks with new devices ASR9K Series is not working. CW version: LMS3.2.1. Device: ASR-9006 AC Chassis. Credentials correct. Screenshot1: inventory request fail.
View 8 Replies View RelatedOn our CiscoWorks 2000 installation, running on Solaris with LMS3.2 and RME4.3.1, we noticed a few weeks ago, that the job "Inventory Collection" needs more and more time to finish. At the moment the job execution time is as high as 8 hours, compared to 3 hours before. When we look at the network traffic during job execution, we see after the collection phase (~3h) several hours with no traffic together with a very high CPU load. I mean to remember that this job used to complete around 15 minutes after data collection phase. Restarting the application and rebooting the system didn't work.When we look in to the IC_Server.log, we find devices with a completion time of over 20'000 seconds. Increasing from day to day. [code]
Affected devices are Cisco Nexus 5548P. We tried to delete/add these devices. That works for a few days, then the runtime starts to increase again.
Are we hitting a bug? And is it possible, as a workaround, to exclude devices from only the Inventory Collection?
I want to gather an inventory of all devices that shows the AAA client name, IP addresses, authentication method and key under my Network Configuration on my ACS appliance. Is there a report to run in it that will shows this, or is something that has to be done manually?
View 1 Replies View RelatedYou all know the senario; A managed device, let's say a c2801 router is being replaced with newer platform, let's say a c3900e series router. Might aswell be a C2960 being replace by a c3750x
I the goodolddays, with LMS3.2.1, you would get the "conflicting device" notice that the SNMP OID has changed on this managed device. you then need to press update and the device would then be managed once more.
How is tyhis done in LMS 4.2.2 ?
I seem to see more and more device in one of my installation, that DCR sees teh new OID and updates, but Inventory fails ... I get more of this, and the error is just; Internalt error in the job-browser .
I see Device Center info is wrong, but DCR info is right ..
What to do, and how do LMS handle this ? Can I get notice around when a device has been changed ?
When I do an Inventory Collection, the job doesn´t work with some devices and I have to restart the server. The job doesn´t fail but the log ICServer.log doesn´t got any information and it works for hours and hours and when it finally stops I can see that devices are not attempted.
I have done some succesfull Inventory Collections with Cisco 3750 switches and 805 routes. I have tried witch Cisco 2811 routers and 2950 and 2960 switches but it doesn´t work.
I have tried to update my LMS4.0.1 but it doesn´t find any actualization. However, in the Cisco download page there are some patches.
I'm currently experiencing some problems with LMS 3.1 where inventory collection fails on cat6500 switches running 12.2(33)SXI1, Sup720.
I have changed the SNMP timeout to 30 seconds.
