Cisco VPN :: VPN 3305 - How To Telnet Or Browse Into Router To Access IOS
Apr 4, 2011
I recently acquired a Cisco VPN 3000 Concentrator Series (fairly old hardware) without a manual, and I'm trying to figure out how to 'telnet' or browser into the router to access the IOS. The device has been reset and I am plugged into the console. I'm running Windows 7 and enabled the Win7 Telnet Client in the OS. Can any tell me how to do this or at least point me in the right direction to obtain the user manual for basic instructions?
Model number: CVPN3005-E/FE
I found the manual for it after going through some hyperlinks. But when you access the console in the Windows OS, is your network connection supposed to show disconnected, or connected but no internet access?
View 4 Replies
ADVERTISEMENT
Feb 18, 2013
i have 68 sites with Routers. On each site I have one equipment DIRECTLY connected to the Router that needs to be accessed by telnet port 23.
I have 15 off this sites that the access via telnet to the equipment’s connected after the routers are not working. These sites are using Router Cisco 3925. The other sites that are working are using Routers Cisco MWR 2921.
Both router models are running the same configuration with no filter on it.
The equipment’s after the routers are all accessed directly via telnet without the router. If the router is directly plugged to the equipment the 15 sites with Router Cisco 3925 are not accessed via telnet.
There is any bug related with the IOS version that Router Cisco 3925 is using?:
Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.1(2)T2, RELEASE SOFTWARE (fc1).ROM: System Bootstrap, Version 15.0(1r)M8, RELEASE SOFTWARE (fc1).System image file is "flash0:c3900-universalk9-mz.SPA.151-2.T2.bin"
View 5 Replies
View Related
Dec 16, 2010
Sothe Internet connection that we have in the office is 22 Mbps down and 10 Mbps up. So, when I connect my computer directly to the cable modem, I get exactly that! But, when I connect the router and connect to the router, the connection drops to 7 down and 4 up. Why?
We have an Adtran NetVanta ...Replace the router? Or, get a different LAN module for the back of the NetVanta?
View 7 Replies
View Related
Aug 3, 2012
i have 2 questions regarding wrt160nl.
1.Is it possible to have ssh or telnet access on the router, with the default firmware?
2.Is it possible to disable one of the antennas on the router, while has installed the default firmware?
View 1 Replies
View Related
Jul 18, 2011
I'm trying to find out if there is anyway to enable telnet access on the WAG120n modem/router .I can't seem to be able to find related info in the support web site for this device. Any info if telnet is even available ?
View 2 Replies
View Related
May 4, 2012
I'm configuring an asa device for web access: SSL VPN service. I can have a user authenticate for web session with their active directory domain credentials (username and password). Once their web session has started, moving to the "browse networks" feature for a share viewing requires them to authenticate once again - "authenitcation required". I'd like to configure the device so that authenticating to the windows file share will be attempted using the previously entered credentials.
View 2 Replies
View Related
Feb 10, 2011
I have the following configuration to enable me telnet to a cisco switch, but couldn't even ping the 192.168.1.22.
vlan 22
!
conf t
int f4/4
switchport mode access
switchport access vlan 22
[code].....
View 8 Replies
View Related
Sep 20, 2012
I've set up this router in the office, and I can access it via PPTP without any problems from home (via windows VPN), Router is sat in DMZ with full access to the internet.
Q1,I've created a 2 phase ipsec vpn with an IKE & preshared key (AES/MD5/1), but I can't find out how to get my encrypted hash for it?also, I can't access the IOS via telnet/ putty, I found an article online explaining how to enable it via url string, but it didn't work,
Q2,I've setup the cisco client on my laptop, and working on the pcf file, without much luck.. Everytime I try to connect it get " error 412. the remote peer is no longer responding. "
With wireshark, I can see the requests been made to the router.. ( from the office )
Within my PCF file i have ...
[main]
Description=MYNAME
Host=<external IP>
AuthType=1
GroupName=vpnname
GroupPwd=<myUnEncryptedKey>
[code]....
View 1 Replies
View Related
Jun 20, 2011
I am trying to access my RV042 through telnet. I go to http://192.168.1.1/sysinfo123.htm?ConsoleSimulation=1
which enables telnet. However when I type my username and password it will not authenticate.
View 16 Replies
View Related
Jun 16, 2011
I try to access to WS-SVC-NAM-2 module in the Switch 6509. But is not work although the HTTP port is enabled (I tested with the command telnet @ip 80).
I try telnet access to the module to check the config , but I always the message that the lo gin / password is wrong even though they are valid.
View 4 Replies
View Related
Apr 29, 2012
We've got a SG200-18 switch that is to be used as a workgroup switch in our environment (SW Version 1.1.1.8). Working with CLI on big and mid-range Cisco-gear over the past two decades I'm having a hard time figuring out the following on the SG200:
o) I want to change the Management-VLAN from the default "1" to the management-VLAN used in our environment. Sure enough I created that vlan in the SG200-config, however when it comes to assigning the management-IP and VLAN for the management interface in the corresponding pulldown under "IPv4 interface -> Management VLAN" the only thing selectable is the default "1". (see screenshots enclosed)So how do I set a management VLAN different from 1?
o) How do I enable telnet/ssh-access to the SG200-18 - I'd be far more comfortable with a CLI-environment?
View 2 Replies
View Related
May 15, 2013
I want to remotely access Cisco 500 switches via TELNET and WEB BASED from a server. I dont know the ip addresses for Cisco 500 switches which are configured as backbone which the ip address assigned on the network is static ip address. Specifically I want to get their configuations inorder to get their specified assigned vlans on the network. I know the ip addresses for their specified cisco 500 switches' gateways. I know that cisco 500 switches can be accesses through web. Is there other ways to solve the problem apart from going onsite and connect to the cisco 500 switches using network cable since cisco 500 swithes dont have console ports?
View 1 Replies
View Related
Jul 11, 2012
I have a network with 3 sites that are on different subnets. Each site has an ASA Right now, I am only able to connect to the ASA that is connected to the subnet I am connected to.I want to be able to connect to the ASA that are on the remote subnets on the address of the inside interface.The sites are connected all together by site-to-site VPN.Is there any way I can achieve that without opening the outside interface directly on the Internet?
View 2 Replies
View Related
Dec 6, 2012
Region : UnitedKingdom
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : Latest
ISP :
In trying to make sure it was NOT wide open to the internet (amongst many other problems of setting it up, which I ,may address later if I can actually connect to the thing ever again) I told it to only accept connections from a range of address inside the LAN. Now it wont accept anything except telnet from the LAN.Short of wiping out 6 hours of trial and error configuration and resetting it, are there any other options I can exercise via the telnet interface?
View 2 Replies
View Related
Sep 3, 2012
I have installed a CISCO v887 router in Amsterdam officeI established a VPN tunnel between AMS office and Edinburg office.
1. The VPN is up and running
2. I am unable to browse anything from LAN computers in Amsterdam office.
3. From LAN computers I can traceroute to yahoo.com but from browser I cant browse yahoo.com and web page hanged out in this situation (website found waiting for reply). But nothing comes over and LAN users are unable to use internet.
[code]...
View 11 Replies
View Related
Sep 3, 2012
I am facing an issue with a cisco 877 router. I am not able to telnet to this router from outside using the public IP. I have also notices this works when the Nat is removed.
View 7 Replies
View Related
Nov 3, 2011
I can connect to skype but i can't browse anything in the internet. I'm using a CISCO WRT54G2 wireless broadband router.I cannot ping also but im online in skype or chatting application.
View 5 Replies
View Related
Apr 5, 2012
I'm having difficulty logging onto my 1801 router over the internet I can ping the device and tracert to it but I can't telnet or SSH ,Here is the config - Can you see whay this would happen. Its on ADSL link.
View 7 Replies
View Related
Apr 6, 2012
Is it possible to enable the snmp in a router via telnet with the wan address(I have the routers' passwords) ? If yes, how
Router 1 : Cisco 871 w
Router 2 : Sagem – F@st 3304 v2
View 5 Replies
View Related
Dec 2, 2011
I am facing a problem that I can not browse the websites (or receive POP emails, but I can send emails) via the DSL router CISCO1941/K9, the DHCP is configured at the Switch (not on this router) and actually the PCs are able to do a ping for the hosts (like [URL] and so on) but they can not browse !!
Below is my DSL router configuration if u would to give a look
Router#show running-configBuilding configuration...
Current configuration : 3434 bytes!! Last configuration change at 19:26:41 UTC Sat Dec 3 2011 by bilal!version 15.1service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname
[Code]......
View 4 Replies
View Related
Aug 1, 2011
We have a router that was installed a few months ago which has the following version: 15.1(3)T
I am unable to reverse telnet to a new ASA firewall, however when I move the console to a second older router with an older version of code I am able to reverse telnet
Are there any known bugs, issues with version 15.1. I use the following command as normal: telnet x.x.x.x 2001
View 5 Replies
View Related
Sep 22, 2011
My Setup / I've been lurking on here a while, working hard to understand the basic networking concepts and eventually pursue the CISCO certs. I bought a lab and have since managed to setup a four router config (2610XM-DTE, 2621-DTE, 2501-DCE, and a linksys E1000 with routing, DHCP, and NAT turned off to make it a wirelss access point) with three switches (2@2950 and a 2924XL).
So far, I have managed to bring in my public IP using DHCP, and setup PAT. The network is fully functional, I can ping every interface, and reach the web on host PCs from any switchport. I am also able to telnet into the FastEthernet interface IPd with my public address.
My Issue : My concern right now is in feature support. I recently read on here that CISCO does not support UPnP, and due to my limited resources, I am using the only public IP I have to allow remote testing/learning on my lab. The issue is that I also have a PS3 and XBox 360 on this network that is requiring UPnP for certain online games and features.
The only solution I can see to this problem is to return my public IP back to the E1000 router, which is running RIP Version 2 (white papers said version 1, but a debup ip rip showed that updates were being ignored due to illegal version), and then poing my other three routers to it for outside access.
The questions I have in this scenario:
1. Will NAT still function if I use the E1000 and set the interfaces connecting to it as ip nat inside? I'm assuming that PAT is already hardcoded onto the router to allow for multiple connections to public IP space.
2. If my IP is 68.X.X.X, I set the E1000 to an IP of 192.168.1.1 and the FastEthernet it connects to is on my 2621 with an IP of 192.168.1.2, would it be possible to telnet into 192.168.1.2? If I were to forward port 23 out of the E1000 to the 192.168.1.2 address. Will my login and password for line vty 0 4 understand the request if the original telnet was to my public IP?
3. If all of that is just non-sense, is there another work-around that allows me to acheive UPnP through my E1000, while retaining telnet ability to my lab so I can try things in different scenarios or while I'm away from home?
View 5 Replies
View Related
Aug 28, 2012
Is it possible to connect WRT54GC with telnet?
View 3 Replies
View Related
Apr 23, 2012
We have several routers that can only be accessed on telnet port 6066 (vice 23). I have no global exec privilege so I can not provide config.So my question is: how do you configure the router to accept port 6066 for telnet and deny port 23?
View 4 Replies
View Related
Aug 13, 2012
We have 400 branches is ended on ASR 1002 router. ASR 1002 is the Hub router. When we disconnect/connect WAN interface or Shut/no shut tunnel interface, at the moment, router is not reacheable via telnet.
But if i disable the EIGRP on tunnel interface, tunnel are ok, then when i enable eigrp on tunnel interface, all eigrp neighbourhoods are OK.Is there any way to limit NHRP or EIGRP packets ?
View 1 Replies
View Related
Jan 7, 2013
We have a cisco 2911 router configured with password for telnet login, but I always failed to login use telnet, does any one know any place need to be modify?
View 6 Replies
View Related
Oct 21, 2011
I have just bought a new router and am trying to connect it. I did the basic set up with an install disc to the problem is that when I connect to the Wireless network it only gives me limited access to the internet for instance I am able to use Skype and other applications that rely on internet connection, but when it comes to web browsers (both Mozilla & Safari) it shows the url section loading but only ever makes it mid way (the page always stays blank) .
View 4 Replies
View Related
Nov 12, 2011
Well actually now i have another problem. I easily works to like search on google. for example wikipedia works too. But from the moment i want to go to facebook or something similar, it doesn't work?
View 1 Replies
View Related
Nov 13, 2012
I am working on a friends vista machine and I cannot browse the web internet is connected I can ping say 8.8.8.8 and get a reply but if I ping (url)it say its unreachable. I have reset winsock and the tcpip stack stopped and started the DNS service tried manually entering DNS servers and no luck.
View 3 Replies
View Related
May 25, 2011
Since my brother doesn't want me to download things from his network, I have to use some other guys network. The problem is not to connect, but it's to browse the internet. I do not know why this happens, but it does. The network is unsafe if that
View 1 Replies
View Related
Jan 19, 2011
We've got about 15pcs at work, all on one network. All connect to one switch, and the router connects to the switch so all has internet access. Four pcs has got windows vista on, the rest XP. Yesterday I tuned on the one pc with Vista on, but could not connect to a mapped drive. I checked in the network places, i could see only three pcs, all three xp pcs. I can browse the internet, but not the pcs on my local network, and I can ping the pcs on the network.
View 1 Replies
View Related
Jun 1, 2011
I cant browse my NAS through Network view in Win 7.
I can Ping it and can connect network shares by using it's IP address but it wont appear in my Network as an Icon. My wifes win 7 laptop does see the NAS in her network. I can also see my wifes laptop in the network view. So it must be my laptop.
It must be that my laptop is not resolving the name properly for some reason.
View 1 Replies
View Related
Dec 16, 2012
Recently installed a WRVS4400N router on my home network. Prior to that I was using the wireless built into my FIOS router. I wanted something more secure so I went with the WRVS4400N. I turned off the FIOS wireless and am only using the cisco wireless.
Im having intermittent issues with the wireless. I have many things hooked up to my wireless including a HP printer and a Sonos system. Most of the time if I just open my ipad I cannot see anything else on my network including the printer. If I try to see the Sonos system can cannot, sometimes I can open the app on my iphone and then I can see it.
Sometimes I can see the printer and sometimes I cant. Sometimes when I do see it and then print to it, it will be gone before it even prints.
I don’t seem to have any issues thru the LAN connections.
Also, ive noticed that the wifi is much slower than the old FIOS box.
FYI, when I remove the cisco and fire back up the FIOS wifi I don’t have any problems at all at any time. And its much faster.
I have tried channel 6, 11 and auto. Also turned off IPC and still no change.
View 1 Replies
View Related
