Cisco WAN :: 1921 - Slow Connection / Cannot Open Websites?
Jul 2, 2012
Regarding to subject above, I using Cisco 1921/K9 which I have bought from ECSM on 19-march 2012 currently facing a problem with the cisco. My problem is the I can’t browse most of the webpages and very slow browsing even I’m using Unifi 10mbps .
I couldn't open websites ex. msn.com / yahoo.com but if i bypass the cisco router there is no issue appear. I have checked the setup and there are no problem on the configuration or the Unifi line . I think it would be any hardware problem. I have attached the info of configuration the cisco .
View 2 Replies
ADVERTISEMENT
Feb 22, 2011
I was playing a MMO game called Wizard101, when randomly, I disconnected from it. I tried first to re-connect to the game, no success.So I tried going to its website, loads very slowly, sometimes not loading at all.Then I wanted to try go to its fansite, to ask for support there, but it turns out that the fansite isn't loading too.I try to load a few more pages that is related to the game, but none of them will load.However everything else seems to load just like normal.
I try to fix this with using my usuall fixes:
- I tried connecting to the websites on another computer. Didn't work.
- Restarted my internet + reset my router back to standard. Neither did this work.
I haven't changed any of my internet settings in a few months; so I doubt anything there would be the problem.
View 1 Replies
View Related
May 22, 2011
I just installed a Cisco ASA 5505 in my company's network,however the network became so slow and many websites cannot be opened or it takes toolong to open (yahoo, hotmail etc.) resulting to a request time out sometimes.
Here is my configuration:
ASA Version 8.2(1) !hostname xxxxxxenable password xxxxxx encryptedpasswd xxxxx encryptednames!interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 !interface Vlan2 nameif outside security-level 0 ip address
[Code].....
View 2 Replies
View Related
May 7, 2011
I am using Comcast as an ISP and have a standalone Arris modem. I, obviously, have a DIR-655 router REV B with a firmware revision on 2.00NA. I have already turned off packet shaping and QOS. Also, I have set the firewall settings to Endpoint Independent for both TCP and UDP, and assigned static IP addresses to my computers. The problem I am having is that whenever I go to any secure websites, i.e. anything that starts with https, it takes an extraordinary long time to log in and to navigate to any webpages therein. I also cannot upload photos to a website and when I try the Speed-test.net website the download speed is OK but the upload test errors out, it doesn't connect.
View 2 Replies
View Related
Jan 21, 2011
I loaded in Qwest wireless software for their internet and now I can not open half the pages I use to be able to.
View 1 Replies
View Related
Feb 24, 2013
I currently have a problem connecting to certain websites via wifi using our home connection. We have the same issue with an HP laptop, Nexus 7 tablet, and also with an iPod. We tried connecting to the internet using other methods or using other connections, and the devices worked as expected.For example when using our wifi, I can open the results page of Google, but when I try to go to the website it won't load. I can download using Google play on my Nexus, but I can't access social networking sites on all three devices.
View 1 Replies
View Related
May 14, 2012
I'm unable to open a few websites through the DIR-825. I can connect the PC to the ISP modem and these sites open just fine. It's not a browser problem.
I've updated to the very latest firmware and still have the problem. I've also researched this issue and can't seem to find a work-around for this issue.
View 7 Replies
View Related
Aug 15, 2012
when i am browsing,automatically new websites are being opened in new tabs.
View 2 Replies
View Related
Jan 16, 2013
Been more than 2 years since I purchsed this router from US and has been working flawlessly till now. Lately I have been facing issues with few websites not opening when my laptop is connected to the router using a lan cable. Sites like speedtest.net (I get the download speed but when it needs to upload it is stuck there forever), [URL] is another which just does not open.
I tried opening these sites using e4200 wifi and everything works perfectly. I even updated the firmware to the latest 1.0.05 build 7 Aug 23, 2012 but still the same issue.
My router set to Automatic configuration - DHCP...
Also when I directly connect the internet cable to my laptop lan, everything opens without any issues.
View 4 Replies
View Related
Nov 26, 2011
There's a WRT54G2 v1.5 router in the apartment I just moved in to (belongs to my roommate) which crapped out the other day. My computer and iPod touch both recognize the router's signal and connect to it, but I can't access any Web sites after that (both work fine on other wireless networks). I can, however, access the Web via the cable modem, but when I plug an Ethernet cable into one of the ports on the Linksys router, I have the same problem as when I'm connecting wirelessly. So far, I've tried resetting the router (with the reset button on the back), updating the firmware, changing settings (beacon interval, frag & RTS thresholds....saw that suggested on other forums) & leaving the network unsecured (it's currently WPA2/TKIP & AES, what it was originally).Is it safe to say this router's done for, or is there anything else I can do to resurrect it?
View 1 Replies
View Related
Apr 10, 2012
When I connect through my router, GMail, Livejournal, Yahoo and Facebook and some other sites are really slow, especially Google and Livejournal. If I connect directly to the modem, they are fine. I've reset the modem to factory and it's still slow on both my Vista PC connected with a cable and my GF's Macbook on wifi. I clear the cookies regularly, use CCleaner, scanned for adware, viruses. What do I do?
View 14 Replies
View Related
Jun 23, 2011
I got a new DIR-655 RevB today, and set it all up. It works fine right now in terms of speed, but certain websites (specifically, facebook.com) load very slowly on wireless. I've tried on two computers with different browsers / operating systems and it still loads slow. I also have comcast which I use a linksys router with, and it loads instantly. Connecting through wired works. Also, I get no slow down when connecting wirelessly if I use a VPN. When I do a speed test, I get my full speed, so that's not a problem.
A few things I have tried:
-Changing the wireless channel
-Disabling QoS
-Disabling traffic shaping
-Changing DNS servers
-Transmit only N/G
-Reducing MTU size
-Disable Dynamic DNS
-Disable advanced DNS service
-Connect to facebook through SSL and not
-Turning router off and on again
Also as a side, unrelated problem, whenever I enable a few ports to be forwarded, I can't connect to the internet when either wired or wireless?
View 6 Replies
View Related
May 23, 2012
I have the port numbers but do not know how to proceed from there. Router is a WRT160N V2.
View 9 Replies
View Related
Jun 24, 2011
I have an SMC2804WBR router. It runs slowly and refuses to even load some web sites. If I unplug it for half an hour, it works fine for three or four minutes and then slows right down again. SMC support told me to reset and reconfigure the settings. I tried it twice. It made no difference at all. It works fine for a few minutes after it has been unplugged but then slows right down. I have the cable connection plugged into a PC running Windows 2000 and that is where I have the router plugged in as well. This is not the machine I use on a daily basis. I use a MacBook Pro via wireless. If I purchase a new router that says the operating system can be OS X or at least XP, can I configure it from the MacBook and will it still work with the PC running on Windows 2000? I was thinking of scrapping the SMC and getting a Linksys E1200-CA.
View 1 Replies
View Related
Mar 14, 2012
I have on Desktop wired to the router which is my main pc. When I access internet the website load really slow, but when I connect the pc directly to Comcast modem, it's blitz fast. My internet speed is 15 Mbps. I have another desktop and laptop. None of them have the problem. What settings I have to change to get back to speed I used to have before.I messed up some settings on the Cisco Connect and accidentally reset the router. After re-installing the router the problem started.
View 9 Replies
View Related
Feb 16, 2013
Region : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
View 4 Replies
View Related
Aug 16, 2012
I purchased the AE3000 Wireless Adapter for my PC, and has been working fine until now. When I first start my PC, my ping starts anywhere between 20-80, then after I try to access anything on the internet it shoots up between 600-1200. It just started happening about 3 days ago, but now it has gotten worse. I can't play any online games, and websites are slow to load.
View 1 Replies
View Related
May 23, 2012
I have a 2911 router with some cisco 2950 switch WAN is 4Mb fiber Why open a Web page is very slow. [code]
View 5 Replies
View Related
Jul 18, 2011
im having a problem with a network drive on a gigabit network that is shared from a file server. Theres a few shares that all contain similar ammounts of data (about 80gbs worth) however one drive for some reason takes 5 seconds to open. It doesnt matter which computer on the network you try from either its still delayed. This has only in the last week started happening. Other drives set up open instantly.
View 9 Replies
View Related
Apr 3, 2012
has full Download/Upload speed while I only have a max. of 5kb/s download speed. The ping is perfect (20ms) and the upload rate is around 150 kb/s. I tried it out with my laptop on Windows 7 and Ubuntu and also with my Android Smartphone. I don't know why it's not working.
View 7 Replies
View Related
Sep 20, 2011
I have a small Windows XP Workgroup network. We have a large folder on the server with over 10,000 image jpgs. Up until six months ago it opened fine, but now when I try to open this folder from any of the workstations it takes several minutes.I've tried unsuccessully many of the proposed fixes over the past few months included changing the RAID controller and this is my last resort.
View 1 Replies
View Related
Oct 5, 2012
We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability
delay down 1 up 1
!
track 20 rtr 2 reachability
delay down 1 up 1
ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else. If Cisco-921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?
View 4 Replies
View Related
Nov 13, 2011
I hope this question has not been asked here in the past, as I have googled for answers many times..I live in UAE and the ISP here blocks many sites and services which made me do the following:I have a notebook PC running WindowsXP with two connections to the internet.LAN connected to my ISP which is 30mb/sWLAN connected to the internet through DD-WRT router running OpenVPN and the speed is not that fast.hat I do now is that I have to disable my LAN and access the internet through WLAN (VPN) and have to enable LAN again whenever I need to download large files
View 5 Replies
View Related
Feb 28, 2013
At our small business I would like to be able to test connecting to some of our websites as an external IP address user outside of our network although still being physically connected to the internal network. Any thoughts on the simplest way to set this up? I have the capability to setup vlans on our switch, could I make one of the vlans/ports have an external connection instead of an internal?
View 1 Replies
View Related
Feb 14, 2013
The aDSL circuit is up and connected and I can reach the internet, however not all sites on the internet are reachable. This is occurring on two seperate 887VA’s and the circuit has been tested with a netgear router and no issues occur. The router has been tried on 5 different ADSL connections and the same problem occurs although more websites can be reached on a home broadband connection (ADSL2+ Annex A) as opposed to the problem being more severe on an ADSL2+ Annex M circuit. The problem seems to affect websites that are full of adverts more than sites that have single domain landing pages.
The sites that I cannot reach are pingable. This happens on multiple machines behind the router. The same config is used on an cisco 877-M router with no issues.
! Last configuration change at 14:52:30 UTC Wed Feb 13 2013
version 15.2
no service pad
[Code].....
View 8 Replies
View Related
Apr 26, 2011
We are using a CISCO1921-SEC Router. On the "WAN" side we have 1 public IP Adress assigned by DHCP. At the moment we are using the WAN Interface with a crypto-map as endpoint of some IPSec connections. We set up a zone-based-firewall with "WAN" and "LAN" zone. In this setup all IPSec Endpoints are on one Interface - connections to the "LAN" zone can be managed by rulesets. What about connections between IPSec connections and the zone "self".We like to terminate each IPSec connection in a separated zone. How can this be configured ?Each one on a "tunnel inetface" with "tunnel source ..." binding ?
View 4 Replies
View Related
Oct 26, 2012
I would like to use a Cisco 1921 at my house and create a "Easy VPN Remote" connection to our ASA 5510 at work. Can I use the Easy VPN Client with the base license, or do I need the security license to take advantage of the VPN tunnel?
View 4 Replies
View Related
Apr 3, 2011
I recently upgraded my modem and before then my internet connection was working. I was able to connect to websites and all. But once i upgraded it wouldn't allow me to connect. my other computers are able to but not my main one. My ISP told me to bring it in to the shop cause they said something was blocking my connection. I ran some basic things i saw on the internet. i am able to get to web pages through ip address but not through the [URL] type ones.
View 18 Replies
View Related
Oct 15, 2012
I am attempting to bring up a remote router using a pppoe connection by replacing the current Tenda 308R router with a Cisco 1921 using the Ethernet connection on the WAN side. The connection works fine with the Tenda in place but when I put the Cisco in I get no connection and no answer for my PADI queries.I always get padi timer expired. I do not think it is even getting to the ppp authentication. [code]
View 5 Replies
View Related
Nov 9, 2012
i have a laptop and i don't have an internet in it so here are some wirelesses connections but all of them are sercured it asks me to enter the security key to access to the point so is there anyway to open it like to hack it without having to know the Password key?
View 1 Replies
View Related
Oct 4, 2011
My connection is modem to vonage adapter to wireless Time Capsule router. I get to the Internet with no problem, but my VoIP phone is not connected. I was told the ISP blocks VoIP. Now I'm using a VPN to be able to use Skype. Is there a way to override the blockage on the Vonage connection.
View 1 Replies
View Related
Sep 27, 2011
I'm wondering if it's possible to setup SSL VPN connection via OPEN VPN client?I'm a Mac OS 1.7 user with Tunnelblick.
I tried to use "built-in" SSL VPN Tunnel client but unfortunately it's not working - during installation Java exception appears saying that either I don't have admin privileges or there is not enough space.. Of course I'm admin and there is plenty of space...
View 5 Replies
View Related
Mar 18, 2011
my dial up connection isn't available on my cellphone's wlan
View 1 Replies
View Related
