Cisco WAN :: Running Config Different From Start-up On 6509 Msfc2 Reset
Jan 25, 2011
I had to reset a 6509 MSFC2, using reset command on the switch. However when the msfc2 reloaded it had a different configuration than the starup-config. I have a daily backup of start-up config and it was very different from that. I had to make many changes to bring it back to normal. What now I dont get is from where did the msfc2 got this config file? and how can I avoid this from happening again... I want it to load start-up config when it loads. [code]
View 2 Replies
ADVERTISEMENT
Jan 19, 2011
I need to upgrade IOS on my 6509 MSFC2. Below is the software version I have on the Sup2 and msfc2. The reason I need to upgrade the msfc2 IOS is that I need to implement ip sla/object tracking and it is not supported by the current version of IOS on msfc2. How do I select the new IOS that I should upgrade the msfc2, in order to achieve object tracking...I see a long list of IOS in the software download section of 6509 msfc2, but not sure which one to choose..
WS-X6K-SUP2-2GE: Sw : 8.6(4)
WS-F6K-MSFC2: Sw : 12.1(19)E1
View 4 Replies
View Related
Apr 17, 2012
If i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies
View Related
Nov 15, 2009
I have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
View 9 Replies
View Related
Nov 30, 2011
I have two 4506 switches in my organization. Recently the office was relocated and when both the switches were booted they ignored the startup config.The config-reg was set to 0x2101. No boot system command was configured.So I changed the config-reg of SW1 to 0x2102 and gave boot system command as stated below.When reloaded the switch booted to ROMMON and I had to manually boot the IOS.I want them to boot normally with IOS.Config of SW2 is not changed since relocation. I am specifying both configs bor your consideration. [code]
View 12 Replies
View Related
Mar 15, 2012
how can i take backup of startup config to tftp server through tftpd server.I am using 4506e switch
View 2 Replies
View Related
May 30, 2012
I had my network running seamlessly for years, I set it up using a guide from a magazine and had both wired and wireless working A1 and originally it was all win xp pro, 2 desktops and a laptop but got a macbook pro and got that using printer, sharing fies etc. All no problem and it was all easy peasy BUT I have mucked up big time and I think it was because I downloaded some system cleaning software, advanced care, toolwiz and pc pitstop but I was not paying attention and I am sure I clicked a few buttons I should not have done. Result disaster, no longer can share files or print etc.ll I want to do is reset everything and start afresh but how do I do that? I use a netgear router with norton security on main desktop. I have a wii, an xbox, apple tv running as well along with 2 desktops, a laptop and a macbook pro. Tried a few things but nothing worked, when I click on network places I get a list of shared folders but end location shows internet! I have to use netgear switch boxes as well but should not have caused the problem.
View 4 Replies
View Related
Dec 23, 2012
We just changed over to Comcast Business and after changing the outside interface to new IP and setting static route. I have access to internet and everythig appears to be good, However asdm will never fully load, alway stuck at 17% or 77%, and I always see "parsing running config".
When I do a show run it will not fully load either, always stop at certain out put. 5 seconds after pulling the Comcast cable out both asdm and running config will load fine.
View 12 Replies
View Related
Jan 14, 2013
We have LMS Prime 4.2. I know how to view the running config on a single device. How do I run a report that will pull all the running configs of all my devices in one report? I'd be able to same them as one big pdf or text file. ]
View 1 Replies
View Related
Oct 6, 2011
Any sample config for a remote access VPN on a Cisco Catalyst 6509 (with VPN mod).? Been searching just cant find one!
View 1 Replies
View Related
Oct 10, 2011
In our company we use the ACS 5.and i have a small problem, what we need to do is.create a profile that will allow SHOW RUNNING CONFIG but not configure terminal.i am investigating and im a littel bit lost i have created a new group but i dont see any option to put permissions.
View 1 Replies
View Related
Oct 20, 2011
have some problems with setting up jobs for the backup running config on my switches. Have RW and RO contact with everyone and can change the config in editor, but do not get config.txt
View 1 Replies
View Related
Aug 9, 2012
I am looking to replace the active supervisor (S720-10G) on our 6509E running in SSO mode. The new module already has the same IOs version as the standby supervisor.Once I have swapped the module how do I know that the config has sync'd correctly other than checking the logs? Is it a case of looking at the "Redundancy Mode (Operational)" state and ensuring is says SSO?Also, is there a command that will force a config-sync if it is running in a mode other than SSO?
View 1 Replies
View Related
May 28, 2013
I recently changed the entire configuration on two 6509 switches, and the fibre modules on slot 7 and 8 have gone down on BOTH switches. It would be easy to say that its a hardware fault but I cannot understand how module 7 and 8 can go down on both switches. Initially I thought it maybe due to IOS bug 22-33.SXI2a.bin" so I upgraded it to s72033-advipservicesk9_wan-mz.122-18.SXF12a.bin but it still down.These are the actions I have carrried out to try resolve the issue:
- Reverted back to orginal configs but no luck
- Tried to use "power enable" command but the status light on both modules seems to turn red and then go off again.
- I have also tried to put one of the fibre modules into a different slot but no joy
- Upgraded the IOS from 22-33.SXI2a. to 122-18.SXF12a
I am sure that hardware fault cannot occur on BOTH modules 7 & 8 on BOTH switches after config change.The error in the log shows that modules "failed to bring online because of registration timer event". I understand this means that it is unable to download the image within the allocated time. [code]
View 7 Replies
View Related
Feb 15, 2011
I've upgraded a 6509 switches wich are running in VSS, from IOS 12.2 (33)SHI1 to 12.2 (33)SHI5. After that I'm facing the folowing log messages periodically. [code] I know that this is a diagnostic result from TestUnusedPortLoopback feature. But this interface is disabled (shutdown).
View 5 Replies
View Related
Apr 2, 2013
I am trying to convince our Technical Lead that dual VSL links between our 6509-E chassis is a VERY good idea but he is fully convinced that the setup will work perfectly fine with only one VSL link. As I do agree that we can do this, I am looking for more concrete evidence that shows this would be a bad setup.
I know that we will lose the High Availably that comes with VSS, what I don't know is what will happen to all of the downstream switches that are connected and what will happen to the two 6509-E chassis..
View 5 Replies
View Related
Feb 21, 2012
in my 6509 switch while i checked is showing some thing like this RDCCI65F0#sh environment
environmental alarms:
no alarms
backplane:
operating clock count: 2
[Code].....
View 2 Replies
View Related
Oct 21, 2012
How I can shutdown a module when I am running vsl.I can use the following command #hw-module module 2 shutdown.As I have modules in both switch 1 and switch 2 how can I ensure I only shut down module 2 in switch 1.
View 1 Replies
View Related
Jan 14, 2013
I'm working at a company that has several 6509 switches running CatOS. They have two of the 6509's running in vtp server mode and the rest as clients. I set up a new vlan from one of the vtp servers and it propagated out. The problem comes when I try to assign a port on one of the vtp clients to this new vlan. It gives me an error that the switch must be in vtp server mode to add/delete vlans. I'm not trying to add/or delete a vlan just trying to add a port into an existing vlan. I'm hesitant to put the switch in vtp server mode. Is this a CatOS thing or is there a specific command to accomplish this?
View 5 Replies
View Related
Jun 5, 2011
my MSFC2 sent this strange log message. %DATACORRUPTION-SP-1-DATAINCONSISTENCY: copy error, The error message decoder tool says: "NOT FOUND". The level is "alert".
View 8 Replies
View Related
May 7, 2013
One of our customer , where there 2 6509 switch , one is Core_sw1 and other is Core_sw2 , catering about 32 Vlan , and HSRP in running for all Vlans , till here no problem , now there internet Router which having one Internet link , which connected and configured on Core_sw1 in a way that one interface of Core_sw1 is given Public IP and there is vlan 85 which internet vlan and vlan 85 ip are natted with that public IP with one simple static route given toward internet router , this is how internet is working ok.
Now i have configured vlan 85 in hsrp as all other are , how can give redundancy to vlan 85 user , that if Core_sw1 get down , internet traffic can get out through Core_sw2.using same internet router with single internet link .i am not talking of ISP redundancy , but Vlan 85 in Core_sw1 goes down , other Core_sw2 will server internet.
View 1 Replies
View Related
Jun 11, 2013
I have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.
View 9 Replies
View Related
May 7, 2013
I need to replace an existing ASA 5540 with a new ASA 5525X. I would like to pre-stage and configure the new box with the existing config, migrate license and export certificate files before swapping it with the old one during a change window. The new firewall will run 9.1 on deployment. Now the same 7.2(4) cannot just be copied over to 5525X running the minimum 8.6 version. There is a Web based tool available at [URL] according to Cisco documentation but the page does not load for me (Cisco intranet only tool ?). Is there another tool for automatic conversion ?
View 3 Replies
View Related
Dec 10, 2012
Does any know what " Last reset from system-reset " means? Is this becouse of a power failure or someone reloading the switch?
View 3 Replies
View Related
Apr 16, 2013
I have the WAP11 serial number G3110320414 that does not have a reset switch in the back. How do I get back to factory settings?
View 3 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Jun 21, 2011
My WCS quit, apparently after the server was rebooted following Microsoft updates while I was on vacation earlier this week.
WCS 7.0.172
Win Server 2003 R2 on VMware
4BG RAM
<6GB of 50GB disk space used.
After stopping WCS & rebooting:Health Monitor is running with an error.WCS is stopped.Database server is stopped Apache server is running After attempting to restart/start WCS:Health Monitor is already running.This was a clean install/upgrade a few weeks ago. 7.0.172 wouldn't install on top of the previous version so I had to uninstall, install and restore. WCS had been solid ever since.
View 10 Replies
View Related
Jun 22, 2011
WCS fails to start with a Tomcat error , see below ;See launchout below - without re-installing WCS
Checking for Port 21 availability... OK
Checking for Port 8456 availability... OK
Checking for Port 8457 availability... OK
Checking for Port 1299 availability... OK
[code]....
View 8 Replies
View Related
Oct 26, 2011
LMS does not start, although the services seem to be started. Find attached the pdshow output and let me know what more you need me to send.
View 3 Replies
View Related
Mar 27, 2012
Today my colleague add 2 lines of access-list to our PIX 525. After 10 minutes, my firewall was rebooted and until now can't start. The booting process as listed below.
The questions are :
1. What is my OS version? Flash?
2. How to remove those 2 lines (reset the config to default)?
Booting process
================
Rebooting..þ
Wait.....
PCI Device Table.
Bus Dev Func VendID DevID Class Irq
00 00 00 8086 7192 Host Bridge
00 07 00 8086 7110 ISA Bridge
00 07 01 8086 7111 IDE Controller
00 07 02 8086 7112 Serial Bus 9
[code]....
View 1 Replies
View Related
Apr 24, 2012
I've two SG 200-50 and I need to use LACP? What should I do?
View 3 Replies
View Related
Dec 12, 2011
UTLite33.exe from Campus Manager 3.3 does not want to start, it gives the following:
"UTLite33.exe is not a valid Win32 application".
View 1 Replies
View Related
