We just purchased a company with multiple sites using Sonicwall's and Dynamic assigned external IP's. I am running a ASA 5510 with a outside Static.
I have done lots of S2S with both ends static but never a Dynamic to static.
what the commands are to set the ASA to accept dynamic VPN tunnels.
My dynamic ASA is trying to use a Cradle point 4G connection to a head end ASA-5510. The remote end with the Cradle point 4G is not even initiating the tunnel! I need another set of eyes. it was initiating the tunnel last week but not completing the connection. Now its not doing anything. i am going backwards. Below is my remote ASA config.
ASA5510(config)# sh run
: Saved
ASA Version 8.2(2)
host name ASA5510
enable password 8Ry2YjIyt7RRXU24 encrypted
password 2KFQnbNIdI.2KYOU encrypted
names
[code]...
I have a laptop directly attached to the inside interface. The PC and ASA can ping each other. The test interface is the one I am trying to use. Does my default route need to point to 192.168.0.1? Or is the remote peer correct? I thought the remote peer was correct? The 4G modem is like a pass-thru device. If I connect my laptop to it I can get out to the internet.
am in the progess of replacing a Zyxel USG 300 to a Cisoa ASA 5510.In the Zyxel I have some Site to Site, where the peer is a dyndns.org adresse, becourse the peer is a dynamic ip-adress.
I have maybe 10 site to site´s where the peer is a dynamic with a dyndns.org adress, and the presharedkey is diffrent at each tunnel.How can i make this configuration at the ASA 5510?
We have an ISP connection that is connected via an ethernet interface on a 5510 ASA. We are allotted 10Mbps. I have currently have the interface set to 10Mbps Full. However we want to upgrade the connection to 25Mbps. I know I can set the port speed to 100Mbps and then set a shape/police statement and shape down to 25Mbps.
Management wants to be able to call the ISP and arbitrarily adjust that speed up temporarily at any time without any user/admin intervention on our side. I can simply leave the port at 100Mbps i.e. no shape statement on my side however I will run into problems with large amounts drops, overruns, retransmissions, etc due to the ISP shaping the connection speed during normal operations. However they then could then adjust the speed at any time without needing me.
I do not know the best way to make this work. Is there some sort of dynamic/smart shaper in the ASA or another cisco device?
I'm trying to figure out how to get two 5510 ASA's to establish a Site-to-Site VPN.The version with two static IP's is working perfectly and stable but I haven't figured out how to get a VPN running between a static and a dynamic IP
View 12 Replies View RelatedThere are three different sites, two are composed of Multilayer switches cisco 3560 and 3570 as core switches (a 3560 in one site and a 3570 in another site), the last site doesn't have any routers just a 2950 switch. Each site has two asa 5505 as firewalls. Two Internet connexions are connected to every site, one on every firewall. One Internet line is used to connect the different sites together using VPN crypted with IPsec and the other line is just for Internet access. The line that is used to interconnect sites contains voice and data traffic.At the moment all the routes are static routes, the network isn't too big for now and counts not more than 20 subnets.But it is evolving, and I want to use dynamic routing, EIGRP to be more accurate. I've looked into it and I'm not sure how to make it work. The VPNs active on the ASAs don't support dynamic routing, so I thought about GRE tunnels but the ASAs don't seem to allow it either.
View 11 Replies View RelatedI have ASA 5510 and public FTP server from my local network to external IP address, with static nat translation. All works, but I need request to ftp come from internal ASA interface (need use gateway different ASA). How configured ASA for forwarding request?
View 4 Replies View RelatedI have one ASA 5510, a primary ISP (cable, the single public IP lives on the ASA), and a backup ISP (ADSL, separate router that hosts its single public IP). I use IP tracking to detect link down on the primary. When I pull the plug on the cable modem and go to "Route monitoring", I can see the ASA's default route is now the backup ISP default route.That conforms with [URL] Pings to 8.8.8.8 fail however, and when I do a packet trace the ASA complains about the dynamic nat rule that still points to the primary ISP's interface.Only when I change the existing dynamic NAT rule (on my inside interface) to use the backup ISP's pool (which is a single 192.168.x.y address) , does 8.8.8.8 reply to my pings. So it kinda works but it's not full auto . I can't add a second dynamic nat rule on the same inside interface, nor can I select 2 IP pools in a single dynamic nat rule.
View 4 Replies View RelatedWe currently have an ASA 5520 communicating with 10 ASA 5510's, all on static outside addresses. I was asked to add 5 additional 5510's on dynamic address. All worked well in testing until it was decided that some of the dynamic clients needed to talk to each other.
My testing shows packets just dying in the 5520.
my computer is XP SP3 and i have a realtek installer with it's usb but when i installed it the xp says cannot install hardware because the wizard cannot find the nessesary software but when i see the install from a specific location i see that it have the files ther i tried it on another pc but it worked what am i going to do?
View 2 Replies View RelatedSince Monday, when I have tried to access my emails in Outlook, a box pops up saying Enter Network Password The box is already prepopulated, with Server: pop3.live.com User name: my email address and a password that shows up as a bunch of stars.
Clicking on "ok" or "cancel" just causes the box to pop up again. (I can still access my emails on Hotmail, BTW, and all internet is working fine). I access the web through Qwest/Century link and MSN.
I am hesitant to delete the password 'cause who knows what it is?? It is NOT my Windows Live/Live Mesh password, as it has one too many stars. But the box came up prepopulated so I assume at some point this was the correct password.
In the past when this happened, you could call Qwest/Century Link and they would walk me through (as best as I remember) redoing all the pop 3 settings. Now, they say they "don't support" MSN.
I am trying to configure QoS on my Cisco 851w router using the class-map command.However it won't accept the class-map command.The router is running cisco IOS version 12.4(15)T10 "C850-advsecurityk9-mz.124-15.T10.bin".
View 3 Replies View RelatedI need to put a FWSM and a line card WS-X6148A-GE-TX to a router 7606. The FWSM version is 3.2(13). The router is running IOS 12.1(18)SXD3. The Cisco document here says the required IOS for router 7606 is 12.2(18)SXF or higher. I have downloaded the IOS 12.2(33)SRD4 and loaded it to the flash card. When I turn the router on, it doesn't load the new IOS and goes to rommon. Which IOS I should use to make the router 7606 work and accept the FWSM.
View 2 Replies View Relatedi have 2811 router can, i use the below image on it , i m thinking to run bgp with ISP to accept just default route.
View 1 Replies View RelatedI have 3750 stack with 4 switches.I am trying to make change some port to new VLAN, but switch 2 & 3 new change never works, the ports stick with old VLAN. Other two switches works as I expected on new changed VLAN.Tried to reboot, no progress.
#Show VLAN command confirmed the VLAN changes are made.
#show switch detail
Current
Switch# Role Mac Address Priority State
--------------------------------------------------------
1 Member 0019.e752.xxxx 1 Ready
2 Member 0015.f9bf.xxxx 1 Ready
[code]......
I am trying to get a 2811 to accept two IPSec peers however can only get one working at a time. I have setup fa0/0 and fa0/1 with their own public facing IP addresses with crypto maps associated to each interface however can only establish connectivity to one interface at any one time.
Relevent configuration below:
crypto isakmp policy 2
encr 3des
hash md5
authentication pre-share
group 2
lifetime 28800
[code]....
its a dell xps 420.
View 1 Replies View Relatedrouter will not accept kodak printer
View 1 Replies View RelatedBoth the integrated wireless adapter in my PC and a USB adapter work fine and conect automatically to my D-Link DIR-615 router. I have the integrated adapter disabled in the control panel. Just bought a D-Link DWA-140 Rangebooster N wireless adapter. This finds all the networks my older USN adapter finds but at greater strength. When I click on connect to my own network I get the enter network key box. I enter the correct key, but get an error message telling it's incorrect. I revert to the older adapter or enable the integrated adapter and I get connected automatically.
View 5 Replies View RelatedI cannot connect to the internet when I try it says "The remote device or resource wont accept the connection" It has been doing this for about 8 days... Sometimes It will connect the Internet explorer... But the past 2 days I CANNOT!
View 1 Replies View RelatedI accidentally did a system recovery. I installed all updates (I think),but now my linksys wireless adapter won't install. It says this version of windows is not supported. It worked before the system recovery. I am using XP.
View 4 Replies View RelatedI am currently on fw 1.33NA and it works fine just want to update so it works better I've tried the reset to factory and unplugged the internet port and ive tried fw 2.0NA and 2.10NA
View 2 Replies View RelatedI just purchased a DAP-1522. The sticker on the bottom says it's a version B1, with firmware 2.0.In the web interface, it says: "Firmware Version : 1.21 , Fri 26 Jun 2009"I downloaded the 2.01 firmware from the D-Link site and when I try to upload it, it says it's not an image file.
View 11 Replies View Relatedi have a WRT54GS flashed with dd-wrt, can i setup a portal, where when you first connect you are redirected and have to accept a set of usage terms?
View 4 Replies View RelatedI use a cisco asa 5520 to terminate multiple site to site VPNs. Due to the configuration of a parteners network, i have had to install 2 routers into this parteners network, i have been supplied static private IP addresses for each router each router has a unidue LAN subnet which is the VPN's protected network.The partener use's PAT with only one public facing IP address.The VPNs are initiated from the parteners network using an IP sla ping.
Upon installing my first VPN router in the partenrs network, once NAT-T was enabled on the local ASA the VPN started working fine. After installing the second VPN router i tried installing the new config on to the ASA but via CSM, the ASA complains that it can not have 2 VPN's with the same peer address configured.
I am trying to connect to a PIX 501 firewall via serial connection. My problem is that I cannot issue commands to the firewall. Whenever I try to type something into the terminal, nothing happens. I have the connection settings configured properly (9600 baud, 8 data bits, 1 stop bit, no parity, no flow control) and have tried PuTTY and HyperTerminal and have the same results. I get output from the firewall, but my keystrokes do not seem to be going to it.
View 2 Replies View RelatedComputer was running fine, then I lost internet connection, ran troubleshooting report, it says the remote device or resource wont accept the connection. Nortons antivirus expired a week ago, tried to resubscribe in case i had a virus, but cant subscribe cause it wont pick up wireless. Have the broadband plugged straight into laptop and still nothing?
View 1 Replies View RelatedI'm trying to connect my printer to my wireless network via my new Netgear Gateway 7550. The printer will not accept the Wireless Network Key for the router.Had no problem with the old 2Wire gateway.
View 1 Replies View RelatedI have a three mobile wireless dongle/modem i want to be able to share it, i have found you can buy wireless routers to do this, but they seem to be £60+ because they also contain a mobile receiver transmitter my question is, is there a wireless router, that accepts a usb dongle for the modem connection rather than containing the mobile equipment? which makes it so much more expensive, as the dongle already contains the mobile part anyway tonyuk123 has chosen the best answer to his/her question.Click here to view the answer that was selected.
View 7 Replies View RelatedI am using TP-Link wireless router model no. TL-WR941ND.my isp provided static ip via cable modem.ip = a.b.c.d subnet = 255.255.255.254 = /31 but the router does not support subnet mask saying wrong subnet mask?
View 2 Replies View Relatedhow do I configure my ipad2 to accept wireless transmissions?
View 1 Replies View Relatedproblems found says remote device or resource wont accept the connection
View 1 Replies View RelatedI get this message in response to clicking on "Diagnose Connection Problems" which was returned to me in I.E. 9 after visiting yahoo.com, other sites and most interestingly, even after trying to get to my DIR-825 at IP address 192.68.0.1. The only common element here is the DIR-825 so I suspect there may be some kind of misconfiguration in the device. The only way that I have been able to clear this condition is to reboot or repower my DIR-825.
View 7 Replies View Related