Cisco Wireless :: 3602 - Minimizing Signal Into Certain Place
Feb 15, 2013
I have a case that to minimize wireless signal into one room.Room has dimenitons 3 x 6 meters.But the signal should pass to other room.I have tried many scenarios but couldnt reach the result that i expect.First i have used a 3502 with external antenna ports , but no antenna attached to it.I have set up the maximum power level from TPC menu from controller , but it was more limited than i thought.I can only connect whenever i put Ap next to myself.Then i have used a 3602 with internal antennas.The reason i have picked 3602 is , it has the lowest gain 2.4GHz antenna attached to it.I reset TPC to minimum power level (5) , but as expected signal can be heard from two rooms from the AP is located.
View 2 Replies
ADVERTISEMENT
Jun 3, 2013
I manage Wi-Fi on a college campus, and we have implemented 802.1x with RADIUS authentication running on a Windows server, and that works well. The issue is that the college is looking at removing wired connections in the dorms in favor of just deploying wireless, and the gaming consoles (Xbox, PS3, etc. ) cannot support 802.1x. We use Cisco 5508 Wireless LAN controllers with 1142 and 3602 APs.
I would like to enable MAC address authentication for these gaming consoles, wherein we (IT) would enter the MAC address of the console for a single connection and allow that console to connect to Wi-Fi, but I do not want to use WEP or any other TKIP passwords, because once the students would know the password they would use WEP/WPA instead of authenticating through RADIUS for their PC/tablet connections. .
View 2 Replies
View Related
Oct 16, 2012
This is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.
View 3 Replies
View Related
Apr 17, 2013
I am looking to enable the internal DHCP on my WLC. I have enabled it and it seems to be operating correctly but I think my routing and or settings allowing me to access anything beyond the private network is wrong.
DHCP is handing out correct IP info and DNS info.How do I route the new private network (10.1.9.*) out to our existing 10.1.4.1. (management IP is 10.1.4.253) Can this be done within the WLC ?
View 3 Replies
View Related
Apr 17, 2013
I am looking to enable the internal DHCP on my WLC. I have enabled it and it seems to be operating correctly but I think my routing and or settings allowing me to access anything beyond the private network is wrong.
DHCP is handing out correct IP info and DNS info. How do I route the new private network (10.1.9.*) out to our existing 10.1.4.1. (management IP is 10.1.4.253) Can this be done within the WLC ?
View 3 Replies
View Related
Mar 3, 2013
The last shipment of 3602 APs for a customer came with 7.3 software. Controllers are running 7.2.110.0 so APs had to be downgraded. After APs finished downgrading they were still up. When we moved the APs to another controller running 7.2.110.0 they would not come back up. Power was denied at the switch.
View 2 Replies
View Related
Mar 7, 2012
We are in the process of evaluating Cisco wireless controllers and AP. We have 3602 APs and 2504 controllers right now. We have multiple branch offices connected to the main office through layer 3 and they all have different vtp domains and vlans. I am trying to deploy APs at the branch offices and connect them back to the controller and the central site. I created a sub interface and ssid with one of the vlans at the branch office on the controller and was able to get the AP to join the controller through DNS. However, a client at the branch office connected to the AP was unable to ping anything at the branch and central sites. Any documentations on how to deploy such a setup where the controller is at the central site and AP at the branch office going through multiple routers in between?
View 1 Replies
View Related
Apr 3, 2013
Is 802.11ac wireless module for Cisco Access Point 3602 is available to order ? what Wireless controller we need to use for the support of 802.11ac wireless standard ?802.11ac will support only on 5700 series wireless controller ? Or it will support with 5508 Series also ?
View 7 Replies
View Related
Jun 4, 2013
I am busy setting up a wireless backhaul.. I have the bridge setup using 2 x 3602's ( Root / mesh) configuration. The bridge is self is up. The main idea is to get older autonomous access point (1231) connected to the ethernet and pull that back in to a temporary building. I have groupped the bridge to only have one SSID on it.
The switch port on the pwr inj4 is currently connected to a laptop - Ethernet Bridging is enabled on the mesh port. Now the laptop does get an ip form the dhcp server. This is where my issue comes in. I can ping the mesh ap's IP address, but not past it.
View 28 Replies
View Related
Dec 2, 2012
How to connect wireless modem in place of wired modem
View 1 Replies
View Related
Jan 3, 2012
I have Network Magic Essentials and use a Linksys WRT54GS router. I just received a Cisco Linksys 2500 and assumed that it would be a breeze to set-up in place of the WRT54, so that I could gain faster internet and improved range. After about six hours of frustration trying to set it up, I am pulling my hair out! I live in a remote area near a lake, and our only option here is a
Wi-Fi signal beamed to our homes via an antenna, coax cable to a "radio" ( Alvarion BreezeAccess). This has always worked very well with the WRT54, but with with the Cisco 2500, I can get on my local network just fine, but I cannot get connected to the internet. I can disconnect the 2500, and reconnect the WRT54, and get right back on the internet.
View 1 Replies
View Related
Apr 16, 2012
I know it is possible to create custom web auth splash pages on the WLC 5508. Is it also possible to embedd a small document (less than 1MB) that users can download directly from the controller? I need this for providing the terms of use for the Guest WLAN.
View 3 Replies
View Related
Aug 16, 2012
I am upgrading from 7.0.116.0 to 7.2.110.0 to support the 3602 APs. Is it a different license to upgrade to 7.2.110.0 or can I directly upgrade to 7.2.110.0 without a new license?We currently have a 5508 base license.
View 1 Replies
View Related
Aug 23, 2012
Can the Cisco 3602 APs be configured by a Cisco 5508 WLAN controller to provide client isolation?
View 2 Replies
View Related
Jan 25, 2013
I have a year old E1200 router. I just updated the firmware today, made adjustments to the MTU range to suit cable service and selected a different channel (9) as the neighbors were mostly on channels 2 and 6.My question is really in regard to the speed results of the router. In the immediate room where the router is located I am getting 17.6 Mbs download speed/ 3.53 upload speeds but if I move to my living room - less than 20 feet away and a few walls - the upload speed drops sharply to 3.21 Mbs download/3.21Mbs uploas.I have read where the router placement can be key. My router is sitting on the desktop. If I elevate the router will it improve performance 20 feet away or should I invest in upgraded router like a E3200 or look into a plug in type repeater?
View 2 Replies
View Related
Apr 4, 2013
I want a low cost solution router with 16 10/100 routed ports...The idea is to club 16 different segments on ofc to this router via media convertor and there will be dynamic protocols such as EIGRP or higher running between these segments.
The router needs to be security enabled...the equipments needs to be a router by defination (not a layer 3 switch)..As per my understanding there is limitation on number of HWIC-2 FE that can be put in ISR G2 series due to which I cannot reach that figure...
Kindly let me know if i can use SM-ES3-16-P in the place of HWIC-2FE for this kind of requirement.
View 5 Replies
View Related
Feb 16, 2013
I'm currently trying to setup a VPN to a Amazon instance but running into a few problems. My current setup is optimum lightpath into a windows 2003 server running ISA 2004 out the a switch handling several servers and laptops/desktops. To setup a VPN connection we purchased a Cisco 1941 IAS but having a problem running this through the ISA Firewall. I giving it a static address and porting it to a external address through ISA <opening UDP and the IPsec 50 and 5000> but nothing. Unles to get this to work I decided to just put a switch before the firewall plugging the optimum router into the switch and then plugging the VPN router and the ISA server in the switch so all the IAS doesn't have to run through the firewall <if I lost you be tell me>
View 7 Replies
View Related
Apr 18, 2011
I have been working nicely with an industrial scanner that runs on Linux, but the harddrive has become corrupted and I need to get it working again. The problem is that the main PCB has a realtek chip which I believe has the most basic webserver abilities that is used in the most basic way possible. To use it ARP commands were used to assign an IP address to the chips MAC address e.g. something like: arp -s 192.168.2.5 00-05-a4-00-a8-f8(the actual MAC address was lost along with the HD)So now I'm starting from scratch in XP, how do I find the MAC address in the first place?
View 4 Replies
View Related
Apr 26, 2013
I am looking to add remote sites that will authenticate with the Windows Server using VPN via Cisco rv042 routers in a gateway to gateway setup.My main concern is the placement of the server to the router and what would be considered best practice.In my mind, option 1 seems to be what I want - however, this would mean disconnecting the WAN feed to the server (my ip is static and tied into the MAC address of the server). While option 2 doesn't look right to me, it would leave the existing configurations in place which would minimize my downtime (I think)
View 10 Replies
View Related
Nov 7, 2011
I'm having a business DSL-connection which requires a modem from the provider (It cannot be replaced by another modem/router)I want to know if it is possible to place the Cisco 877W-G-E-K9 behind the modem and set it up as an VPN-server.The internet connection wil be established in the modem/router of our provider.
View 20 Replies
View Related
Feb 17, 2013
we have tried to use the Cisco Hierarchical model as close as possible. we now have the need for 10 gig servers. we have a 7k, 5k, 6500, and 2960's in our network. we have some open 10 gig ports on our 5k. where is the best place to connect the 10gig servers. or is there a more preferred way to connect these new servers?a 10 gig blade for the 6500, the new 6001 switch?
View 1 Replies
View Related
Mar 1, 2011
HAVE 3 SITES.BUT I WANT TO MANAGE MY NETWORK FROM ONE SITE.I WANT TO CREATE USERS FROM MY MAIN SITE FOR ALL SITES.
View 1 Replies
View Related
Sep 10, 2012
How does Replication of cucm servers and other servers like unity presence and all in a cluster take place?
View 1 Replies
View Related
Jun 10, 2012
We have a main office and 4 remote offices (only showing 1 remote office in the diagram). We are using GRE over IPSec VPNs to the remote offices which terminate on the 2811 router in the main office. We are using the 2811 as it is the only device that we have that can terminate GRE. The 2811 router is connected to the outside switch and is configured with a public IP address. We also have a ASA5510 in the main office which is connected in the same manner and is used for Web, e-mail traffic etc.Both the main office and remote offices have a 10Mbps Internet connection.
We have an issue with voice quality between sites as we are finding it difficult to control bandwidth utilization in the main office. When users in the main office download web content it can saturate the 10Mbps Internet connection causing voice quality issues. We have configured outbound shaping on the branch routers to make sure that aggregate inbound traffic from all branches to the main office does not saturate the link but we cannot control traffic from the Internet.I understand that controlling inbound traffic from the Internet is difficult without controlling QoS on the ISPs side. Is there any way that can reserve inbound bandwidth to ensure that web traffic does not impact voice? Also in this design, which is the best place to configure outbound QoS from the main office?
View 4 Replies
View Related
Dec 29, 2011
I have an ASA 5510 that I want to connect to 2 isp (one of my private network uses the isp1, and all others the isp2). Excluding the 5510 does not accept PBR(policy based routing), i saw that you could put a router, like cisco 2811 in front of the ISP. my questions are : can i put a switch 3750 in place of the 2811 router? , I have vpn connections in isp1, this architecture is compatible?
View 2 Replies
View Related
Dec 16, 2011
Difference between mapping a drive and adding a network place...?
View 2 Replies
View Related
Sep 1, 2012
Have WBR-2310 D-Link router. Internet modem and wireless router were working. While trying to connect new wireless printer, lost internet connect. Had to re-enter internet provider user id and password. Was told I needed to make sure that information was in my D-link router, so I typed 192.168.0.1 as internet address. I don't get a webpage to enter the userid and password.
View 2 Replies
View Related
Jul 25, 2012
we have several Dell machines using W7 and all of them are exhibiting the problem of not connecting to some wifi sources. The wifi appears to connect but no internet connection takes place.
View 1 Replies
View Related
Dec 5, 2012
We will be converting two 6500s to VSS. Each chassis has a Sup2T module, fwsm, 6908-10G blade, wism1 blades and two or three 6748-SFP blades. I was wondering how long the conversion process takes? If I remember correctly at the 2012 networkers lab it took maybe 10 minutes while using Sup720s. The instructor mentioned that with Sup2Ts it would convert a lot faster.
View 3 Replies
View Related
Apr 20, 2011
How to place security + a password on a folder that is shared on a local area network. i don't want other users to access the contents in the folder since we are all on the same local network.
View 4 Replies
View Related
Jan 22, 2013
Today, I received the Dell Inspiron 660s I ordered and I had a question about the network port on the computer. Is the network port the place for connecting a router and then the router connects to a modem, or is there another connection I should make?
View 1 Replies
View Related
Mar 13, 2007
I use a BEFVP41 VPN router. I have changed several settings. How can I backup these settings and store these settings in a save place.
View 3 Replies
View Related
Jan 22, 2013
Cannot get on net although there is a signal.
View 1 Replies
View Related
