I have upgraded my WLC 5508 from 7.0 to 7.4 and the AP 1310 no longer can associate to WLC.
Seems that the AP doesn't work with WLC ver 7.4
Except changing these APs to autonomous mode, any other alternatives?
Besides, if we change them to autonomous mode, can Prime Infrastructure manage/monitor these APs?
After upgrading to 7.2 on my 5508 WCS, the 1310 APs will no longer join. After a call to TAC they said the 1300 and 1400 APs are no longer supported on WCS. Is there any plan to add them back as supported in future releases?I was thinking I could downgrade my backup 5508 and change the APs to autonomous. Or is there some easier way to make them autonomous?
Also, as a low cost outdoor AP, I guess I am reduced to putting 1262s in a NEMA box with outdoor antennas. The 1552s are way too expensive for the quantity I need. Is there some other inexpensive outdoor AP that will replace 1300-1400 series?
Is it possible to rename the default webauthentication URL from [URL] to something like [URL]. We are running on 7.0.98.0, is it possible to do http for web authentication and https for Mgmt access if we upgrade the controller software?
We configured our guest wireless with no layer 2 authetication so users can associate with an AP and get an ip adress but they can't go anywhere unless they have a valid username and password(web authentication) - does this affect the performance of an AP since there will be many people associated with each AP, is there any setting in the WLC to de associate a client from an AP if its idle for certain time.
I have 10 Access-Point model 1131 AG are new AP.
When I connect the access-Point to the network, the AP associate only one time but i go to wireless for see the AP, i can see downloading of IOS, but the ios is 3.0.59, the ap don not nothing. I can not change any parameters.
I have a 5508 WLC licensed for 100 APs. I have 1 - 1042 LAP connected for testing. I have DHCP configured for the AP, and it gets an address of 192.168.254.100/24 - the controller's management interface is 192.168.254.99/24. I can see that the AP is getting an IP and I can ping it from the controller. However, I simply do not see the AP associating. I enabled capwap debiugging and watched the events, but I didn't see anything crazy that clued me in. What am I doing wrong?
The controller is v6.0.199.4
Every time I have set these up in the past they have been pretty straight forward. I haven't gotten too deep into the config on the WLC becuase I don't want to cause more issues.
I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error, I get this error from the LAP 1310 console as below:
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface
[Code].....
I have Cisco 5508 WLAN controller v7.4 and i have lap 1310 and it is not joining to this lan controller. What to do? How to join this lap to this lan controller? or how to convert it to autonomous because i dont find mode button on this access point?
View 6 Replies View RelatedI have 2 campuses. I have my 5508 wireless controller working beautifully on my main campus using LDAP. (YAY!!) Now for my problem. My remote campus has 1310 bridges. I was able to successfully upgrade one of them to work with the controller, however, I can't get the other two bridges to talk to the one that I upgraded and I can't get them to upgrade, it indicates that they need to be the root. I have several small buildings on that remote campus, than need that remote bridging in order to be able to have network access.
View 7 Replies View RelatedCan I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies View RelatedI want to upgrade a 5508 WLC from version 6.0.196.0 to the most recent 7.4or 7.3 is it ok to skip so many versions, will this cause an issue?
View 9 Replies View RelatedI have 2 * 5508 wlc , LAP1142 , want to implement wlc fail over , so what is your recommend WLC software . How about 7.3.101.0.
View 6 Replies View RelatedI have upgraded my new WLC to version 7.0.98.218. I noticed the N/A for the Field recovery version. On my old 4402 it is called the Emergency Image Version, and it is 5.2.157.0
How do i get a recovery version on the WLC?
How many APs does wireless controller 5508 and WCS (version 7.0) supports?
View 7 Replies View RelatedI have 2x WLC 5508 running version 7.2. 1st one is setup and running. My questions is: If I want to setup Active-Passive redundancy, do I need to manually setup the 2nd one exactly as the 1st one and put them in the same group? Or is it a way to copy all of the configs I made on the 1st one over to the 2nd one?
View 4 Replies View RelatedNew to working with Wireless and the Cisco Meshing concept so have a few questions to ask.I currently have the majority of the mesh setup and configured. I have a setup with two RAPs with 9 MAPS connecting to each RAP.
First question is how many MAPS can connect to a RAP generally?Secondly how can I block other cisco AP's that are not in my mesh network from trying to connect to my AP's
The below is constantly hammering the logs for 6 devices that are Cisco close to my mesh that are not mine.
8
Sat Nov 12 23:31:53 2011
Mesh child node '58:35:d9:aa:db:4f' has changed its parent to mesh node '88:f0:77:b7:c6:e0' from mesh node '88:f0:77:b7:c6:c0'.
Mesh Node '58:35:d9:aa:db:4f' failed to join controller, MAC address not in MAC filter list.
I have only added the MAC addresses of my AP's in to my AP Policy under security. Would these other AP's affect the mesh in any way?What I am seeing is the AP's constantly changing the child to parent relationship. I have inherited this network and they have about 20 AP's all within a square mile which is absolutely overkill. Would this close proximity of AP's together be the cause for the constant child parent changes?
How close should I have RAP's together. The network was setup so two raps are about 20 metres apart and the AP's on one side connect to RAP1 and the other to RAP2?How do you deal with Radar? The install is pretty much next to an airfield with radar running and a few times I have seen all the AP's disconnect and change channels.
My understanding is that for fully WLC 5508 integration with ISE 1.1.2, it needs Version 7.2.103.0. Question is if customer has 5508 with either 7.0.230 or 7.0.98, and ISE 1.1.2, can AAA part work? what part will not work, any potential issue if they don't upgrade 5508 to 7.2.103?
View 2 Replies View Relatedi have a wlc 5508(version:7.2.103) and oe600 ap, recently,someone oe600 does't work which has no ssid from the ap,so i cannot connect the wifi to access internet,but the ap still associated wlc,the LED display orange.according the cisco document,
[URL]
using a Cisco 5508 controller (code version 7.4.100.0) with an ACS appliance running version 4.1 or 4.2?I've found that the ACS constantly reports a 'Bad request from NAS' (Invalid message authenticator in EAP request). message. This usually indicates a mismatched shared secret but this isn't the case.The controller works fine opposite a Microsoft NPS Radius Server.
View 6 Replies View RelatedI know that the recommendation from Cisco for the mobility anchor feature to work well is to use the same IOS version on the anchor WLC and local WLC controller. Now I´ll install on a new site a 5508 local WLC with a newer IOS version which is installed on the other controllers ( Guest and local ). Later I´ve planned to update also the other controllers to the same IOS version. Now my question is, must I upgrade all other controller at the same time ?
View 4 Replies View RelatedWhat is the latest IOS version for the WLan Controller 5508 ?
Actually I am using, Software Version7.3.102.0
I see the following at Cisco website:
Latest Releases
7.2.115.1(ED)7.3.112.0(ED)
7.0.240.0(ED)
7.4.100.0(ED)
I need to know for shure if the aps listed below are compatible with 5508 controller version 7.1.91.0
the ap's are
AIR-LAP1242AG-E-K9
AIR-LAP1242G-E-K9
AIR-CAP3501E-E-K9
AIR-CAP3502E-E-K9
AIR-LAP1231G-E-K9
of course I checked release notes [URL]
I am using WLC 5508 version 7.0 facing issue while enabling global multicast mode .
client machine stops DNS resolution after some time once we enable global multicast mode on WLC .websites are opening with IPs but not with DNS names .
DNS resolution starts working immediately after disabling multicast mode on wlc .
I am trying to SSH into my controller after upgrading to 7.0.103 and I get the username prompt but it seems to be disconnecting as soon as I do. Is there something different about this version of code as opposed to the older ones?
View 1 Replies View RelatedI will install next week at a customers side a new Pair of 5508 Controller. They have at the moment one old 4404 with about 70 APs.So the bought the new 5508 with HA Pair.For the HA i will need 7.3 i read in the High Availability (AP SSO) Deployment Guide.There are now two 7.3 Versions, or i can choose the new 7.4 Version.
AIR-CT5500-K9-7-3-101-0.aes
AIR-CT5500-K9-7-3-112-0.aes
AIR-CT5500-K9-7-4-100-0.aes
So what software version will be the best at the moment?I will install also a Cisco Prime Infrastructure on a ESX host.For the 7.3 in can use the 1.2 , but for the 7.4 i must take the 1.3.
we have the following situation:
- 2 x WLC 5508 with about 80 - 120 access points (Aironet 3500) each
- 7 x WLAN's with different security settings
- 2 x ACS 5.3
On one WLAN we have the problem, that the students with their own laptops have to enter their AD username about 4-5 time, until they get a successfull 802.1x authentication. The WLAN has the following configuration:
- Hidden SSID
- Only 802.11b/g
- Interface assigned via AP Groups
- WPA2 / AES with 802.1x or CCKM (here I could only allow 802.1x, the clients do not need fast secure roaming)
- Authentication via ACS 5.3 and PEAP
- for more details see screenshots below
Most of the time I can't see any 802.1x authentication attemps on the ACS View, but when there are entries, they are successfull. So in my opinion I think there has to be a problem on WLC side, but I don't know where to search further. We already deactivated the client load balancing in the WLAN, because at the beginning the customer wanted to activate that - but it was clear that there are a lot of clients which had to authenticate multiple times.I know there were some bugs in the 7.0 train, so I upgraded finaly to 7.0.235.0 to overcome this bug here: CSCty07036.To fix the other bug (CSCtt70290) I just disabled all the session timeouts on the different WLAN's.
I need know how many clients can associate for this AP model
AIR-CAP3502I-A-K9
AIR-LAP1131G-A-K9
I have 45 clients currently associated with each AP.
I am trying to have both my laptop and brother HL-3070CW printer, wirelessly connect. I go through the entire setup process and all is well. Until the end. It tells me that my security settings are incorrect. Therefore the wireless link status has failed to associate.
View 1 Replies View RelatedI am testing our new wireless network using 1 Cisco 2504 wireless controller with 5 licenses 4 Cisco Air LAP 1142N Access Point I configured it very simple for testing There is only one interface and vlan is untaggetd There is also only one WLAN with one SSID Currently security setting is WPA + WPA2 + PSK (I also tested with no security setup) Wlan session time is diabled and controller user idle timeout is set to 1000000 (Max)AP boot version is 12.4.23.3 and ISO version is 12.4(23c)JA3 Problem is clinet(iphone) does not automatically associate with 1142N Access Point even after it learned network. Phone has to be authenticated again to connect to network same iphone can automatically associate with old 1220 Access point but not with New AP if I urn off and turn back on wifi from iphone, it does see the network but does not connect but I have to manually reconnect to it with password I want iphone to connect known network without reauthentication process after iphone's wifi function is turn on?
View 24 Replies View RelatedI have created new ssid and i want to associate only one IP address with this SSID, so that only this user will be allowed to connect to AP. I have controller 5500 series.
View 6 Replies View Relatedmost of my wireless clients are associating to one ap when there are ap's closer. do i have some setting configured wrong on my controllers?
View 1 Replies View RelatedMcAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
View 9 Replies View RelatedI just installed a WAP321. I literally configured a test SSID, implemented WPA Personal security, and could not get an iPad or Blackberry to associate with the network. The error message that appears in the Blackberry is "EAP Authentication Failed". But isn't EAP applicable only to the WPA Enterprise mode? The access point works fine if I have the test SSID without any security, but as soon as I turn on WPA Personal security, nothing can connect. Is there something really obvious I'm missing here?(When I select WPA Personal security, I have tried with just the "WPA2" version and "AES" cipher selected, as well as with check boxes ticked on both WPA/WPA2, and on both TKIP/AES. Neither works.)
View 8 Replies View RelatedWe have other APs that associate w/o issue AIR-LAP1141N-A-K9. However our 1 1310 is having issues.. The Controller log shows:
2012-08-29 21:16:51 local0.error 172.16.10.70 ITCNJ1WC01: *spamApTask0: Aug 28 21:17:15.038: %LWAPP-3-DECRYPT_ERR5: spam_crypto.c:293 Error decrypting packet (using old key) from AP d4:8c:b5:15:3c:04 (session identifier a3ddb9c5)
2012-08-29 21:17:33 local0.error 172.16.10.70 ITCNJ1WC01: *spamApTask0: Aug 28 21:17:17.037: %LWAPP-3-DECRYPT_ERR: spam_lrad.c:3642 The system is unable to decrypt image data message; AP d4:8c:b5:15:3c:04
2012-08-29 21:17:33 local0.error 172.16.10.70 ITCNJ1WC01: *spamApTask0: Aug 28 21:17:17.037: %LWAPP-3-DECRYPT_ERR: spam_crypto.c:735 The system is unable to decrypt LWAPP packet; AP d4:8c:b5:15:3c:04
[code]....