Cisco Wireless :: AIR-CAP3502I-A-K9 - How Many Clients Can Associate To AP
Nov 18, 2012
I need know how many clients can associate for this AP model
AIR-CAP3502I-A-K9
AIR-LAP1131G-A-K9
I have 45 clients currently associated with each AP.
View 2 Replies
ADVERTISEMENT
Sep 17, 2012
we have the following situation:
- 2 x WLC 5508 with about 80 - 120 access points (Aironet 3500) each
- 7 x WLAN's with different security settings
- 2 x ACS 5.3
On one WLAN we have the problem, that the students with their own laptops have to enter their AD username about 4-5 time, until they get a successfull 802.1x authentication. The WLAN has the following configuration:
- Hidden SSID
- Only 802.11b/g
- Interface assigned via AP Groups
- WPA2 / AES with 802.1x or CCKM (here I could only allow 802.1x, the clients do not need fast secure roaming)
- Authentication via ACS 5.3 and PEAP
- for more details see screenshots below
Most of the time I can't see any 802.1x authentication attemps on the ACS View, but when there are entries, they are successfull. So in my opinion I think there has to be a problem on WLC side, but I don't know where to search further. We already deactivated the client load balancing in the WLAN, because at the beginning the customer wanted to activate that - but it was clear that there are a lot of clients which had to authenticate multiple times.I know there were some bugs in the 7.0 train, so I upgraded finaly to 7.0.235.0 to overcome this bug here: CSCty07036.To fix the other bug (CSCtt70290) I just disabled all the session timeouts on the different WLAN's.
View 5 Replies
View Related
Feb 23, 2011
most of my wireless clients are associating to one ap when there are ap's closer. do i have some setting configured wrong on my controllers?
View 1 Replies
View Related
Aug 10, 2011
I have one room within which clients have problems associating.When using AirMagnet however one of the AP s appears to have the strongest S/n Ratio and overall signal strenght.I would have thought that would be the obvious AP for clients to associate with.However that is not the case and the users are trying to associate with various APs with lesser signal strengths. None of them have 100 % utilisation and if they all tryed to associate with the AP with the strongest signal that would alleviate the existing association problems. We are using AIR-CAP3502E-E-K9 with WCS 5500.
View 2 Replies
View Related
Sep 21, 2011
This summer the IT department at my location rolled out a little more than 100 AIR-CAP3502I-A-K9's to much success. We have had an issue with only one AP. This paticular AP must have gotten unplugged during the updating process after the initial conneciton to the controller was made as the LED currently blinks red-blue-red, indicating an error in the flash memory according to the manual.
View 2 Replies
View Related
Dec 14, 2011
We've just replaced some 1240 LAPs with 20 x 3502i.
Seem to have a problem, most of the 14 * 3502i have regersted on the network and working, 6 arent connecting and log below. I've replaced one of the AP with a differnt one, same model and batch and this works.
WISMs on 7.0.98.0
Scirpt
*Mar 1 00:15:16.015: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code].....
View 11 Replies
View Related
Nov 23, 2011
I was under the impression that the AIR-CAP3502I-E-K9 is a ceiling mount AP only. Is any one using these as wall monuted AP's?
View 5 Replies
View Related
May 8, 2013
We are setting up one of these for the first time. It is in a constant rebooting process.
Here is the boot process:
r WRDTR,CLKTR: 0x8200083f 0x40000000
r RQDC ,RFDC : 0x80000032 0x00000211
using eeprom values
[Code].....
View 3 Replies
View Related
Dec 9, 2012
i've one of my 3500 that when finish to download the os, the front led stop working. During the power on and all the test the led is flashing in various colors pretty ipnotizing :-) When it bacame operative, the led stops. If i issue the test led flashing console command it works.
View 1 Replies
View Related
Oct 18, 2012
I have 1 cisco AP (CAP3502I) which is not able to associate with WLC (version 7.0.235.0), using CAPWAP. Simply from debug I can see that AP is trying to contact WLC on port udp/5246 but can't see any response from WLC.
*Oct 19 07:06:50.055: UDP: sent src=x.x.x.x(4271), dst=wlc.wlc.wlc.wcl(5246), length=47
AP is getting config about WLC from DHCP option 43 and have own reservation to get same IP address (+default GW). AP is NOT associated but as it has IP address from DHCP then it is pingable. But don't know why, but I'm not able to tracert/traceroute to this AP, as I can see it is getting packets but it is not responding.
But on different locations, where are same APs model (associated with WLC) I have no problem with traceroute it, as APs are responding.
My question: It is not related that AP is not able to associate with WLC (still working on it) BUT should I be able to traceroute/tracert to unassociated AP (to his IP) and get response???
NOTE:
==> WLC is in DC and AP on one location, so diagram could be: WLC ---- L3 device ---- Provider MPLS router..........Provider MPLS router ---- L3 device -- L2 switch --- AP (CAPWAP)
@It means that there is NO FW on tha way :-)
I check many other APs with same model and non of them has problem to respond for traceroute, but this particular unassociated one has :-
View 3 Replies
View Related
Jan 28, 2013
Can i run both 2.4 and 5ghz at the same time? so my N user's can connect at 300Mpbs on the 5ghz bonded, and my G users can connect to 54Mbps?Also i ask because of coverage, my 5ghz does not cover as far as the 2.4 so those at the extremity's could at least get G with a good signal?
View 4 Replies
View Related
Aug 27, 2012
I have this issue after Cisco send us RMA. Whenever i restart the AP, it wont able to auto boot. I have to type command manually to boot the AP. Is there any command or way to make this AP to auto boot?
View 7 Replies
View Related
Mar 22, 2012
I'm wondering if there is an easy way to change the regulatory domain on a lightweight access point. The reason I'm asking is someone accidentally placed an order for AIR-CAP3502I-N-K9 access points instead of the AIR-CAP3502I-A-K9 flavored ones. I can see how it happened, since undoubtedly someone asked for the "N" access points, thinking 802.11n, and the other person was thinking AIR-CAP3502I-"N"-K9.
do I have to RMA them, or is there a way to magically turn them into the ones flavored for the Americas?
View 12 Replies
View Related
Jan 31, 2011
I am trying to have both my laptop and brother HL-3070CW printer, wirelessly connect. I go through the entire setup process and all is well. Until the end. It tells me that my security settings are incorrect. Therefore the wireless link status has failed to associate.
View 1 Replies
View Related
Jun 19, 2012
I am testing our new wireless network using 1 Cisco 2504 wireless controller with 5 licenses 4 Cisco Air LAP 1142N Access Point I configured it very simple for testing There is only one interface and vlan is untaggetd There is also only one WLAN with one SSID Currently security setting is WPA + WPA2 + PSK (I also tested with no security setup) Wlan session time is diabled and controller user idle timeout is set to 1000000 (Max)AP boot version is 12.4.23.3 and ISO version is 12.4(23c)JA3 Problem is clinet(iphone) does not automatically associate with 1142N Access Point even after it learned network. Phone has to be authenticated again to connect to network same iphone can automatically associate with old 1220 Access point but not with New AP if I urn off and turn back on wifi from iphone, it does see the network but does not connect but I have to manually reconnect to it with password I want iphone to connect known network without reauthentication process after iphone's wifi function is turn on?
View 24 Replies
View Related
Apr 2, 2012
I have created new ssid and i want to associate only one IP address with this SSID, so that only this user will be allowed to connect to AP. I have controller 5500 series.
View 6 Replies
View Related
Sep 16, 2012
Is it possible to rename the default webauthentication URL from [URL] to something like [URL]. We are running on 7.0.98.0, is it possible to do http for web authentication and https for Mgmt access if we upgrade the controller software?
We configured our guest wireless with no layer 2 authetication so users can associate with an AP and get an ip adress but they can't go anywhere unless they have a valid username and password(web authentication) - does this affect the performance of an AP since there will be many people associated with each AP, is there any setting in the WLC to de associate a client from an AP if its idle for certain time.
View 9 Replies
View Related
Apr 18, 2013
I have 10 Access-Point model 1131 AG are new AP.
When I connect the access-Point to the network, the AP associate only one time but i go to wireless for see the AP, i can see downloading of IOS, but the ios is 3.0.59, the ap don not nothing. I can not change any parameters.
View 4 Replies
View Related
Aug 23, 2012
I just installed a WAP321. I literally configured a test SSID, implemented WPA Personal security, and could not get an iPad or Blackberry to associate with the network. The error message that appears in the Blackberry is "EAP Authentication Failed". But isn't EAP applicable only to the WPA Enterprise mode? The access point works fine if I have the test SSID without any security, but as soon as I turn on WPA Personal security, nothing can connect. Is there something really obvious I'm missing here?(When I select WPA Personal security, I have tried with just the "WPA2" version and "AES" cipher selected, as well as with check boxes ticked on both WPA/WPA2, and on both TKIP/AES. Neither works.)
View 8 Replies
View Related
Jun 11, 2012
I have a 5508 WLC licensed for 100 APs. I have 1 - 1042 LAP connected for testing. I have DHCP configured for the AP, and it gets an address of 192.168.254.100/24 - the controller's management interface is 192.168.254.99/24. I can see that the AP is getting an IP and I can ping it from the controller. However, I simply do not see the AP associating. I enabled capwap debiugging and watched the events, but I didn't see anything crazy that clued me in. What am I doing wrong?
The controller is v6.0.199.4
Every time I have set these up in the past they have been pretty straight forward. I haven't gotten too deep into the config on the WLC becuase I don't want to cause more issues.
View 2 Replies
View Related
Apr 19, 2013
I have upgraded my WLC 5508 from 7.0 to 7.4 and the AP 1310 no longer can associate to WLC.
Seems that the AP doesn't work with WLC ver 7.4
Except changing these APs to autonomous mode, any other alternatives?
Besides, if we change them to autonomous mode, can Prime Infrastructure manage/monitor these APs?
View 2 Replies
View Related
Aug 27, 2012
We have other APs that associate w/o issue AIR-LAP1141N-A-K9. However our 1 1310 is having issues.. The Controller log shows:
2012-08-29 21:16:51 local0.error 172.16.10.70 ITCNJ1WC01: *spamApTask0: Aug 28 21:17:15.038: %LWAPP-3-DECRYPT_ERR5: spam_crypto.c:293 Error decrypting packet (using old key) from AP d4:8c:b5:15:3c:04 (session identifier a3ddb9c5)
2012-08-29 21:17:33 local0.error 172.16.10.70 ITCNJ1WC01: *spamApTask0: Aug 28 21:17:17.037: %LWAPP-3-DECRYPT_ERR: spam_lrad.c:3642 The system is unable to decrypt image data message; AP d4:8c:b5:15:3c:04
2012-08-29 21:17:33 local0.error 172.16.10.70 ITCNJ1WC01: *spamApTask0: Aug 28 21:17:17.037: %LWAPP-3-DECRYPT_ERR: spam_crypto.c:735 The system is unable to decrypt LWAPP packet; AP d4:8c:b5:15:3c:04
[code]....
View 3 Replies
View Related
Feb 1, 2011
I have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies
View Related
Feb 12, 2013
ragarding AP AIR-CAP3502I cannot learn option 43 from MS server but it can learn the DHCP ip address. We have 2 sites that option 43 does not learned by new AP's but other site works ok. I tried also to delete and add the dhcp scope and same issue. My temporary solution will be creating the DHCP pool with option 43 and 60 in the access switch and it work ok, new AP's able to show in the WLC. I just need more information why site AP's cannot learn the option 43 of the MS server but other site AP's work ok. Is this IOS bug? AP's issue? MS issue?
View 6 Replies
View Related
Apr 14, 2011
I have just installed 3 access points along with 6 repeater access points all running V12.4. They are all AIR-AP1242AG-E-K9 using the 2.4GHz radio.
Prior to installation I bench tested that the repeaters would associate with the access points and if one of the access points was turned off the repeaters would automatically roam to another access point. I did not have all 9 devices powered up at the same time, but did have 2 repeaters and 2 access points powered up to simulate association and roaming.
During installation as access points and repeaters were powered up everything behaved as expected (repeaters were associating to access points etc.) however during installation once everything was installed the 3 access points were all powered down for half an hour or so and once powered back on the repeaters did not automatically re-associate until they were re-booted.
I have now configured the repaters with parent MAC addresses to reflect the above current assocaition pattern but not yet powered off the access points to test if this forces re-association as this is now a live operational site!!
Is it normal to have to re-boot the repeaters if ALL 3 access points are powered down at the same time? i.e. If only one access point is powered down will the repeaters automaically roam to another access point o.k.?
View 5 Replies
View Related
Mar 9, 2013
have a problem with my EA6500 router. I can't connect to the internet, the connexion works fine. But, everytime i go on the smart wifi login page, i enter my login and password and then i'm asked to download the software for my EA6500 and to associate it with my account. The problem is that i just can't update it manually because i couldn't ever go on the tools page. Never.So i'm here with a great router but i can't configure it. I asked the support service several times but they always asked me to reset the router. Nothing changes.I 'm still unable to process after the login page, i have created a account successfully, i can login but everytime i just get stucked at " Associate your router with your account" page. My only options there is to click on OKAY or a link to download the firmware on Linksys support. I get the firmware but i can't install it because i can't go in the administrative page.
View 4 Replies
View Related
Apr 24, 2013
I have configured my new EA2700 successfully, upgraded the firmware to Smart Wi-Fi, can access it locally and configure anything as expected.
However, when I log on with my (validated) Smart Wi-Fi account, I am always stuck at this page (see screenshot below):
- Logon to [URL] works fine
- The I am redirected to this page
- Now I can only click OK
- Logon again to [URL] --> start over again...
The firmware is the latest version 1.1.39.145204 and no other updates are found. I tried IE and Firefox --> same result.
View 2 Replies
View Related
Jun 22, 2011
My desktop can go to internet with ethernet wire on. After installing wireless adaptor driver, the adaptor shows green solid light on 'power' and blinking light on 'Link'. The Linksys icon shows 'Cannot associate with the access point'. I called Verizon and was told that the adaptor might have problem. I want to know if really the adaptor's problem or the adaptor installation problem.
View 1 Replies
View Related
May 29, 2012
I have 10 new AIR-CAP3502I-A-K9 connected to a WS-C3750X-48PF-L switch. 8 of the APs power on and connect perfectly, but two are problematic. Both devices are granted power, but they never go past the stage of getting power from the switch. A look at POE shows: [code]
Where the AP that is not working is connected to Gi1/0/4. The interface shows down/down. I've tried shutting the interface, removing power, cdp etc.
Are there any other tricks you can think of to get it working or would you say that it's 2 faulty APs? I am not based at site unfortunately so I cannot console to the APs and check them out.
View 5 Replies
View Related
Jan 2, 2013
I just setup my new Cisco EA4500 and upgraded to latest firmware and signed up for my account.Local access to the router works fine and I see the Smart Wi-Fi admin/config interface However when I try to go to the following site: url...To access Linksys Smart Wi-Fi Tools, your router <em>requires</em> the <a href="url...Series Linksys Smart Wi-Fi Firmware</a> and you will need to associate your router with your Linksys Smart Wi-Fi account.On a computer or device connected to your router, open url... and follow the instructions. This requires that you enter the router password so have that ready.
However I see no way to perform the association step - my account exists and my router is configured.I am doing all this behind this router wi-fi network not remotely.
View 4 Replies
View Related
Oct 18, 2011
i got the problem with 1300 bridges,root bridge with omni antenna and non root with sector antenna , it can associate and can pin each other , but whenever i try to browse several web pages its get timed out and radio was down.
View 5 Replies
View Related
Nov 27, 2011
Is there anyway to associate a name to an IP in the RV220W? I am coming from a WRVS4400N v2. Folks are complaining that they can't connect, for example via Real VNC, via the PC name any longer. They have to use the IP address. In the past I put the names of the PCs in the WRVS4400N when I reserved IPs via MAC addresses (some call this assigning static IPs). There isn't any place in the RV220W to put the name. Even when I look at the DHCP list a lot of them show up as "unknown". I am sure this is a NETBIOS thing but I'd rather fix this in the router as I have always done in the past.
View 4 Replies
View Related
Jun 18, 2012
I have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
Result of the command: "show running-config"
: Saved
:
ASA Version 7.2(4)
!
hostname ASA
domain-name default.domain.invalid
[code].....
what I need to add to get the vpn client to be able to ping the router and clients?
View 3 Replies
View Related