Cisco Wireless :: WAP4410N Does Not Exceed 130Mbps In N Mode At Close Range
Sep 25, 2011
I have a WAP4410N which I have had for awhile and the performance was flawless at what appeaared to be 300 Mbps. I udated the firmware recently to 2.0.4.2. This is when the problems started. Within 15 feet of the acccess point it would drop the connection and speeds were under 65 Mbps. I factory defaulted the unit and reinstalled the firmware with no changes. I run several other access points of differnt manufacturers and I get fantastic performance on draft N and G. I did check all the laptops for network adapter incosistansies. Have I made a configuation mistake? I only changed the IP address to bring it into the range of other devices. I use a sa520 router and a Trendnet Gigabit switch and a server with MS SBS 2008 which works well with all but the WAP4410N.
View 2 Replies
ADVERTISEMENT
Sep 18, 2010
I have a simple wireless network that works fine, except for one room where the signal is too low. So I purchased a WAP4410N to use as a range extender. provide the exact settings that are need to set this up? I have tried many, many different configurations, and I can't get it to work properly. In particular, it will not give me an IP address and therefore won't connect. Also, is it important to use the SAME SSID name? or better to use a different name so as not to confuse the two signals (base unit vs repeater (4410)).
View 1 Replies
View Related
Jun 17, 2011
I have a WAP4410N access point. In the datasheet, it shows that the Antenna Gain in dBi as 2. I need to increase the range of the access point by replacing the antenna with a 7dB one. I would like to know the maximum dBi supported by this access point.
View 0 Replies
View Related
Jul 11, 2011
Will the WRT160N work with the WAP4410N range booster? Will it power the booster over ethernet cable? my location has several concrete walls and the signal from the router is blocked. Will the WAP4410N work better in this environment?
View 1 Replies
View Related
Aug 29, 2011
The admin guide for the WAP4410N, explains the default setting for the Wireless Network Mode field:
"B/G/N-Mixed—(Default) Connects all the wireless client devices at their respective data rates in this mixed mode."
What does this mean exactly? Does it mean that I can have some clients using G at G speed; and some clients using N at the faster N speed? And both at the same time?
I can't see how that is possible as the AP only has one radio?If it is possible; then why is one of the options G only - that allows both G and N, but a G speeds only?
Should I set the Channel Bandwidth to 20Mhz or 40Mhz? The admin guide says that N will use 40Mhz and B/G will use 20Mhz. What is the difference in practice?
View 4 Replies
View Related
Sep 21, 2010
I also have problems with this type of accespoint, i have 2 (one in AP mode and the other in Client/Repeater mode).
Very often the connection between the pc and the repeater, and also between the 2 accespoints just "drops" out (like its resetting itself).
The accespoints are in enough range of eachother, so thats not the problem.
After the contact with Cisco here in Holland they said this type (4410N) is not stable with the 2.0.0.5 firmware, and its also limited to the B and G (not N) wireless, because else the accespoint will be even less stable??.
When can we expect a propper solution to this Cisco problem?
View 18 Replies
View Related
May 26, 2012
1) Apparently, my Cisco modem likes to assign new IP addresses to things, so I didn't figure out the web access page until an hour in (was NOT 192.168.1.245)
2) Do I input the same IP address, subnet, DNS and default gateway as my Cisco modem? It has a wireless router and switch bundled in, should I use the wireless network's MAC address or the wired?
Currently, it's set to 'automatically configure':
IPv4
Local IP Address: 192.xxx.x.xx
Subnet Mask: 255.xxx.xxx.x
Default Gateway: 192.xxx.x.x
Primary DNS: 64.xx.xxx.xxx
Secondary DNS: 0.0.0.0
I can access the page fine, but I cannot get the wireless client working...
3) I did a site survey and found my existing network and inputted its SSID and MAC address, but nothing happens. I still get one bar on my wireless devices indicating the AP isn't working.
View 1 Replies
View Related
Jun 16, 2011
I want to configure two AP WAP4410N in Bridge Mode and I don´t find the correct configuraction tips.
View 11 Replies
View Related
Sep 21, 2010
I have just been escalated to Level 3 support about my bridging issues.Bridge / Repeater mode configuration separated by 150 feet. Worked perfect for over 3 months.Upgraded firmware due to lockups starting to happen, now cant get the bridge / repeater to work longer than 15 min.After MANY support calls, new devices sent (version 2's) still no luck.
Talked to Marcelo at1 866 606 1866 and he stated that the Bridge / Repeater mode will not be supported farther than 50 Feet.(seems like a cop out to me) He didn't seem to have an answer as to why it worked for 3 Months other than interference Of which I have ran spectrum analyzers and see no Interference. **** even 10 feet away I cant get the units to work longer than 15 min.So I definitely think the 50 foot thing is a BS answer.
Also they have told me that External Antennas are not supported with these devices.Again even though People 500 feet away connect just perfect (without a bridge / repeater mode) with 50% coverage!
so here I am (spent 600 bucks) on bricks.. and nobody will support the device and I cant seem to get my money back.I have 8 customers with these devices, I am not going to use Cisco any longer. However will continue to fight this,as we all seem to have the same BS issues.
View 1 Replies
View Related
Dec 13, 2012
I have been using WAP4401N for almost a year in our office and I’m very happy of this device, never had any problem. So I bought 3 new ones for our customer which supposed to work in configuration below:
Network ----- AP1 –Bridge mode ----- AP2 – Bridge mode -----AP3 – Access Point mode.
Everything was working perfectly fine to the moment than bridge was broken. I can get access to all AP (obviously when connected to proper part of network) however not able to ping from AP2 -> AP1 or opposite so basically no link between AP1 and AP2. After reboot everything is working fine to next time (happens twice in two days). When I go to System Performance can see Connection is enabled but doesn’t work.
I upgraded firmware to latest version (2.0.5.3) but haven’t worked. When I’ve done some research found many users having similar problem with this device and basically they recommend to don’t buy. Unfortunately this is not an option for me as I’ve already purchased them.
View 6 Replies
View Related
Dec 7, 2009
I have purchased 4 of these devices about 2 months ago and have experienced all of the issues reported within this thread. The came with the 2.0.0.5 FW rev installed, so unless the 2.0.0.5 on the cisco DL site is different, nothing I can do with that.I've tried making them work as stand alone AP's, Bridge<-> Bridge, etc... all modes seem to lock up eventually needing a reboot to get any functionality back.Ultimately, I need to make them work in AP<->Client-Repeater mode. I've not been successful in making them work in any mode for a prolonged period of time.
having just rfound this thread today, I have not tried hard coding the NIC's to 100/full, but will give it a try. If it works, great, but then that would defeat the purpose of buying an N radio AP. I would like the potential 300Mbps throughput.
View 13 Replies
View Related
Jul 26, 2012
Does the data rate to N connected clients go down to G rate if there is even a single G client connected?
View 2 Replies
View Related
Mar 5, 2011
I am trying to set up a WAP4410n Wireless access point and add to my home network. One problem I can't seem to get around. The IP adress range setup does not accept 1 (example 192.168.1.245) as a range setup for IP address. How do i get in communication with the unit when I can't view the setup due to the factory default set as 192.168.1.245? If it were 192.168.0.245 I could easily change my routers IP range to include it.
View 0 Replies
View Related
Jun 19, 2011
I recently decided to buy a DIR-655 router to create a wireless network in my home. I hooked it up last night and speeds look fine with my rr standard 10mpbs service. However, I decided to check the wireless status and my macbook, macbook pro, and my desktop computer are only getting at most 130mbps. Is there anything i can do to maximize this and go beyond 130mbps
View 3 Replies
View Related
Feb 20, 2013
I have a issue, my DIR-615 V.E3 has been working good. I have multiple computers connected and all get between 280 and 300Mbps. But then after a few hours the speeds drop to 130Mbps on all computers. After I reset the router the speed returns to 300Mbps. I have it set up to run on N speed only so g devices are not connecting.
View 14 Replies
View Related
Apr 16, 2012
D610 - Intel PROSet
tab: Advance>>"Use Windows to manage WiFI" (F10)
When in Windows MODE the view network in range does NOT pick up anything even though the connection still exists.
How do I configure to see the networks in range ?
View 12 Replies
View Related
Jul 4, 2011
My HP Envy 14 has an Intel 6200AGN wireless card. Is it not good enough to achieve 300mbps on my D-Link DIR-655? The firmware is current on the router and the signal is 100% almost every where in my home. Even when I'm a few feet away from the router, the most I'm able to get is 130.Do I need to change a setting on the router or upgrade the wireless card?
View 2 Replies
View Related
Apr 30, 2011
I have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
View 1 Replies
View Related
Feb 9, 2011
BRAND NEW DIR 655. Took a bit to get working. Connected at 300mbps beautifully. Then I started to notice I was lagging--I checked my connection speed and it's back down to 130mpbs.I made sure to do WPA2 only, 20/40 range... I don't know what else to do to make it "stick" to the speed I want. It's obviously quite capable of it. If I reboot it it connects at that speed.... it just randomly reverts back to 130.
View 14 Replies
View Related
Aug 25, 2011
We are trying to create a 4 member (4Gb/s) static LAG group between two switches, a Cisco SLM2048 and a Cisco SG300-52. The LAG group (4 x 1Gb) shows up on both switch and we do get 1Gb/s of throughput between the switch but that’s it. Testing with a flat network and 2 x 1Gb computers on each switch shows we cannot exceed 1Gb/s of combined throughput through the 4 member LAG. Pulling out any 3 of the 4 members shows that the throughput stays unchanged at a maximum of 1Gb/s . Putting all 4 computers into one switch shows they can do a combined 2Gb/s total. So why can’t the 4 member (4 x 1Gb) LAG group exceed 1Gb total?
View 1 Replies
View Related
Apr 9, 2013
Cisco 4500-X do not support egress queing on VLAN interfaces (SVI) which means cannot do a traffic-shapping, is there a work around via policing? I can police the traffic and then on the trunk interfaces do "per-port-per-VLAN" QoS but again only the policing not shapping so I was wondering what is the effect of "exceed-action transmit" command
policy-map SHAPE
class class-default
shape-average 8000000
Versus...
policy-map POLICE
class class-default
police 8000000 4000 conform-action transmit exceed-action transmit
View 10 Replies
View Related
Feb 6, 2012
I just started using NMAP and found that port 139 is open on my router. Browsing through the router's settings I don't see any option for closing ports or disabling NetBios.... how should I go about securing this port?
Here is my router. [URL]
View 4 Replies
View Related
Dec 19, 2012
I just bought a Cisco Linksys E900 wireless router. Can someone explain to me why the router (192.168.1.1 on my case) has ports 1990/tcp and 5916/tcp open on the LAN?? I cannot find a way to close those ports.
[code]...
Every client on the LAN (wired and wireless) can connect to those ports on the router. I do not want that to happen. It is unncessary and it is just not secure. I only want the router to have port 443 open on the LAN for the web mgmt interface. I do not want any other unncessary port open.
View 4 Replies
View Related
Mar 25, 2013
Getting the following alarm from my ISE:Cause:Base License Enforcement Details: Base concurrent users exceed license allowable count.Currently only using 1656 out of 2000 base licenses so I'm not sure what the issue is. Running 1.1.2.145 patch 3.
View 1 Replies
View Related
Sep 24, 2011
I have a Compaq Presario V2000 running Windows XP and whenever i close the lid of the laptop the wireless disconnects.
I have all of my power settings set to NOTHING. I have set the adapter, Minimum Power Consumption disabled, same with the Power Save Mode.
View 6 Replies
View Related
Mar 15, 2012
So finally that my e4200 is capable of disabling wps i run in to another question.
how to close ports 139 445 ? these are open by default and i didnt figure out how to close them, in browser setup..
and YES port 139 IS a security issue. people denying this, are the same, that denied any vulnearibilties to wps.
View 1 Replies
View Related
Dec 7, 2010
Recently I faced 1 issue in MLS 6509.MLS had all Gig modules in slots 6,7,8 taking System detected CRC error rate on port ASIC data bus exceed fatal threshold, ("System detected CRC error rate on port ASIC data bus exceed fatal threshold".) causing the module reset by the SUP. After this active SUP causing it to failover the standby. This process was continuing every few minutes resulting in the SUPs on MLS rolling.what could be the issue for Sup rolling reset?
View 1 Replies
View Related
Jan 31, 2012
How can I Block the port 80 on Windows XP?
View 6 Replies
View Related
Dec 24, 2012
i want to know that how long a tcp should wait for close the connection.
View 3 Replies
View Related
Apr 5, 2011
I opened a computer in other network via remote desktop(because I forwarded port in router)....and tried to access other computers in the network via remote desktop again from that computer but after I done, I don't know how to close the secondary remote desktop. There was one close button on the top, but if "close" it, whole rdp connection was closed. The secondary rdp connection is still open in the computer.
View 1 Replies
View Related
May 3, 2011
I've been trying to set up a customers security camera's for remote viewing. He has a HP running Vista, a netgear grt614 vs10 router, and a static IP address through Verizon. My problem is this. I set up port forwarding for port 80. All seems to work well sometimes and I can connect to his DVR no problem. Then other times I can't connect at all. I'll run a port checker and it will tell me port 80 is closed. Is it possible that Verizon will off and on block inbound port 80? I seem to only be able to connect during buisness hours. Is it possible that his PC needs to be on for the port to be open. The DVR is the server which is always on and the router is always on. I don't know why the computer would have to be on.
View 6 Replies
View Related
Feb 14, 2013
I'm using Cisco AnyConnect VPN Client v2.4.1012 running on Windows 7/64 to connect to a client's network environment. Is there any method to the way that the client forces my Firefox and IE browser windows to close?
View 3 Replies
View Related
Sep 28, 2011
About a week ago my laptop started acting strange. I noticed when I brought my computer to my room (which is where i usually use my computer) it said that there were connections available where the signal bar is. Which is odd because it usually just auto connects. So i clicked on the signal bar and connected to my internet, but it lost the connection shortly after so I clicked connect again and it said windows was unable to connect to the router. Then shortly after that it said no connections were available. So i brought the computer to the computer to the family room ,where the router is, to check the router. It was nothing wrong with the router so I looked back at the computer and it was automatically connected to the internet with a five bar connection, but when i left the family room with the computer it immediately lost the signal. So i decided i should just stay in the family room. The next day the same problem occured and i went back to the family room to use the computer but i noticed the connection wasnt usually at five bars like it usually is wen im that close to the router but it was 4 bars or 3.
The next day i went over my fathers house for the weekend, and when im over there i pretty much always have a five bar connection even though im not in the same room as the router because im 1 floor directly above the router. Now when i used the computer over my dads house it had a 3 bar connection, disconnected from the internet at times, and when i try to connect bak it said that windows could not connect to router like it had said in my room bak at my own house, even though it always used to have a very high connection before this problem happened. So wen i got bak to my house i went to the family room to connect to the internet and now im having the same problems i had over my dads house. Now i try deleting some programs to see if they affected the internet and have even turned off some start off services on using mpconfig but that didnt work either
View 11 Replies
View Related
