Wireless is still on also after time set in the schedule is over. I connected to the router through its web page and set wireless on with schedule from 8 am to 9 pm. But wireless is running also after 9 pm. I checked the time settings on the router and they are correct. FW version is 2.01
View 1 RepliesI have a wireless schedule setup on my DIR-655. Works great. Now I would like to run different hours on different days. Have wireless up on certain hours during the week, different hours on weekends.
How do I set up a schedule to one one set of hours during the week, and a different set of hours during the weekend?
Region : Netherlands
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.4 Build 110429 Rel.36959n
ISP :
I have a flaky internet connection, and it drops every few days. I've thus far powercycled my router by unplugging and plugging it back in, which fixes the issue.
I'm traveling soon, and would like to be able to have access to my stuff remotely, even after the connection drops.
I have two ideas:Run a script in Windows 7 which would soft reboot the modem - free, not sure if soft reboot is enough though. If that doesn't work, Get a hardware which would powercycle the router - haven't researched if these are readily available and cheap
Is there a way to schedule a soft reboot of my router using Windows system tools? I'd schedule it to reboot every night.
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : V1_121225
ISP : Cogeco
I bought the 4300 a week ago - and just recently discovered that you cannot turn off the wi-fi radio using a schedule.
I thought this was "wireless router 101" - since my last three routers had this feature... apparently not with TP-Link.
I have a dir-655 and have two schedules set up, one for weekend and one for week days, for wireless access. Is there a way to switch from one schedule to the other automatically?
View 1 Replies View RelatedIs there any way to schedule the shutoff of WiFi every night between certain hours?
View 1 Replies View RelatedCan I schedule a weekly reboot with this router?
View 3 Replies View RelatedI was just curious if there was a way to allow a computer and a ps3 to have unrestricted internet access while at the same time preventing other devices from connecting to the internet at a scheduled time (12 am to 8 am for example)?
View 3 Replies View RelatedDIR-615, HW rev. H1, FW v8.02
As the subject says... Sending logs using "On schedule" option doesn't work. I have my own personal email server I used to test this. When the router time reaches the defined "Start time" nothing happens. I tried both time formats (12h, 24h). The router does NOT initialize the process of sending the email. I see that in my server mail logs. If sent manually from Status -> Logs -> Email now, it works. If sent using "On Log Full" option, also works.
Any way to schedule a reboot of a DCS2102?I've got 3 of them here, and they are very good but every now and then they seem to stop writing to the storage. They haven't frozen cause I can still connect to them via a browser
View 2 Replies View RelatedIs it possible to get a time and date stamp on the image when using the FTP on a schedule? The time and date stamp is shown on a live video image on pages 20 and 21 of the manual but I'm not seeing how to get it on snapshots.
View 3 Replies View RelatedThis is on a DIR-655, firmware 2.01NA, hardware rev B1.Is there a limit on the number of DHCP reservations that can be added to this WAP?This WAP was working fine with 10 DHCP reservations (wired & wireless devices), 6 schedules, Access control of 2 devices by MAC (6 defined, only 2-3 active at a time).I started adding additional DHCP reservations, because I'm simplifiying my network, and when I add the 26th DHCP reservation I get the message "Schedule rules is Full! Please Delete an Entry."
I've been adding all of the new DHCP reservations as disabled, but I haven't assigned any schedules or otherwise to these new devices yet. So what's up with this message??
I realize that this is a new product, but nevertheless I have some feedback after running my 4 new DCS-930L camera over the past few days.
Currently, you can configure the camera to EMAIL/FTP images on a schedule or when motion is detected, but not both.
Why does it matter? Because I get flooded with email alerts after I get home from work and later in the evening every time I walk by one of the cameras or whenever a light switch is turned on/off.
If I could configured the motion detection to only alert during a specified schedule of days and hours, it would be great!
We have two 5508s in a boarding school environment and about 5 wireless networks. Administration wants to know how can we shut down the student networks @ 11:30pm and then have them come on @ 6:00am. Othern than doing it manually is there another way?
View 3 Replies View RelatedIs it possible to create a managed schedule to switch the wireless radio on/off? I want to set a start time and a stop time so that e.g. the wireless can be switched off during nighttime.
I had previously routers from both dlink and zyxel and they both had this feature.
I am sensitive to electromagnetic radiation and bought the EA4500 due to the 5 Ghz capability, - but then only to discover that the radio always has to stay on (at least as far as I have found out.
I just bought a RV220W. One of the features I need to setup is a daily wireless plan, i.e. parental control: my wireless connection needs to be open at different times depending on the day, for 2 specific wireless devices, while others wireless devices have continuous access. Unfortunately, the wireless schedule only lets me set up one start/stop time only (i.e. the same one every day).
I noticed that I could possibly set up a firewall access rule with a specific schedule, but I have no idea if this would work, and how to set it up. My basic idea was then to open the wireless SSID I want to control from 7.30am to 11pm every day, and then add a firewall rule that would close the access to the said devices (using their MAC address) from say 10-11pm on given days... But I am not quite sure how to set this up.
I own a WRT54G linksys router. works really great but i'm missing two features - being able to change the tx power - being able to turn wifi off on a schedules you can guess, i'm being apprehensive regarding EMF, so i'd like to turn off wifi at night and lowering the tx signal to the minimum required.the question: i saw two alternative firmware, dd-wrt and tomato, I think they both offer the tx signal control but no one has wifi schedule. do you know if there is a firmware which specifically gives me the requirements i need?
View 2 Replies View RelatedI have ACS 5.2 and would like to know if I can schedule a report to be sent to my email address each Sunday for example for all the failed and succeeded attempts for devices authentication.
View 3 Replies View RelatedThis week, I replaced a netgear FVS318G with a Cisvo RV180, firmware 1.0.2.6. I have a very limited knowlege of routers and protocols, mostly from exposure as a home user. My goal is to define firewall rules on my RV180 that define when my tween-aged kids can and cannot play on X-Box live, as was the case on the FVS318G. I am aware that X-Box has several port ranges. Specifically, I have defined the following for one XBox port range to always block, as an example:
[code]...
A similar rule on the FVS318 would block XBOX (and also on a schedule), but this is not the case on the RV180. I guess I don't uderstand how to correctly implement rAccess Rules on this device.
I would like to schedule automatic backups of our ASA5500's OoO-hours:
1. SSH from secure server and create _FULL_ backup - what would be the CLI command(s) ?
2. SCP from secure server and retreive file(s) - what is the location of the file(s) ?
LMS 4.21
Solaris 10
Trying to schedule a Best Practices Network Discrepancy Report everything works find (reports could be scheduled) except entering a eMail-Address in Textfield: E-mail.
Hitting the Submit Button results in nothing, no popup stating the created job ID; without any content in this field a job is able to be scheduled.
I have Ver E3, with firmware 5.10. Like it says above, Wireless N is not working. I've already going into Manual Wireless set up and selected Mixed G and N. All of my devices will connect, but only as G devices.I'm reluctant to set it to "N only" for fear that none of my devices will be able to connect.
View 14 Replies View RelatedI have a D-Link wireless adapter (DWL-G122) that I have been trying to install on a Windows XP computer. After various uninstalls and reinstalls of the drivers and programs that come with it, I have found currently the best way to get it to work is leave the D-Link programs uninstalled and have Windows install the driver itself.The problem is, it doesn't seem to keep the drivers on restarting, so every time the computer is restarted, it must be installed again. This is not ideal.It occasionally worked when I installed from the CD, but the D-Link programs that would install with the drivers created problems of their own.
View 2 Replies View RelatedOnce every couple of days the wireless service seems to disappear. I've connected to the router from a wired computer and everything looks ok from the d-link panel, however its not showing up as an available wireless network on the wireless units. Pulling the power off for 30 seconds tends to get it working again. I'm configured bg and n. I need a mix... an old B laptop, have one machine that has a G NIC, and the rest are N.
View 14 Replies View RelatedMy DIR-655 wireless has stopped working after a few years of flawless operation. It still works for wired operation. I was running Firmware 1.21, tried rebooting, resetting to factory, powered off the unit, etc. without success. Decided to Upgrade to the firmware to 135 NA, still no success. I am in British Columbia on Shaw Cable. On the Status Page under Wireless LAN, the Wireless Radio shows "Init failed".
View 3 Replies View RelatedHow to schedule automatic Xlate sessions cleaning in ASA5550. I want to clear few global nat sessions manually every week.Is there any way to automate that?
View 1 Replies View RelatedI bought the DIR-655 last year and till within warranty. Yesterday, I lost the wireless network on my laptops but internet was working. I contacted the d-link support and during the process of troubleshooting the problem, the internet connection was also lost. I followed all instructions given to me by d-link teams that spoke with me but the problem was not resolved. I tried to call the d-link support but my calls were ignored . Up till now, the wireless and internet connections through DIR-655 are not working.
View 5 Replies View RelatedI have a DIR-825 (B) for over a year now. This morning, the wireless on it suddenly stopped working. Meaning, all my machines not longer seeing the signal from that router. If I hardwire to it, it will work fine. I have check the wireless settings and they all look fine.
View 2 Replies View RelatedMy DCS-942 is doing everything quite well, except when an SD card is inserted. When connected to the network via ethernet, everything works well. I can set detection zones with snapshot or video modes and it does what I want it to do, however, as soon as I remove the ethernet cable and wish to use the camera over wireless, the unit fails to work at all (red light illuminated). If I then remove the SD card, it will work over wireless again with all the capability except for SD oriented operations. I have performed several hard resets and formatted the card with no success.
View 2 Replies View RelatedI have a Comcast modem and a DIR-655 router. I finally got them to work together (it took some doing!) and now the router has stopped working with my Roku player and laptop. It still works fine with the desktop that's wired into it.
View 6 Replies View RelatedThere were 6 computers on the 2.4GHz band, and 2 on the 5GHz.Everytime the people on the 2.4GHz band would get disconnected for no reason, but this router should be able to handle that number easily. After lots of fiddling, like telling people to shut down their phones WiFi, I finally found the culprit:
N and G mixed mode
Even with only Wireless-N devices there would be problems. N-only mode worked well.That is unpractical for me as there are some devices here that are still on Wireless-G, like game consoles and some phones.
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : TPG
URL Filter not working
Region : Australia
Model : TD-W8960N
Hardware Version : V1
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : TPG
Cannot get the URL filter to work Just upgraded to latest Firmware but that didn't work?
URL List Type: Deny Allow Disable
Address Port Remove
[URL]
WRT54GX4 Wireless link not working
View 2 Replies View Related