My DIR-601 doesn't connect to the internet. I connected it through a cable to the modem, and the router to the computer. It worked for an hour, I could even set up the wireless and it worked. Since, I cannot connect the comupter to the Internet through the router, even using the cables connection. I connect to the router, but the router does not connect to the Internet. The modem works properly.
View 1 Replies
I have had this router and everything was working, I have moved and after getting my internet activated I proceeded to set-up a network in my new place. The setup process went smooth but even though I can connect to my network, I cant connect to the internet. I know my internet works as a direct connection through the modem works. I updated the firmware, I tried doing a factory reset on the router, basically did all the basic stuff that one would do if they had router troubles.
View 14 Replies View RelatedI bought this new router, I've followed the CD and install everthing. My computer can connect to the router, but it doesn't connect to the internet.
View 1 Replies View RelatedI have been having difficulty connecting to the internet at my new place, I'm starting to think that the network card I recently bought (D-Link DWA-552 XtremeN Desktop Adapter) might have a problem, but I am not sure. I am currently using my landlord's internet, so I don't have access to the router to turn it on and off, which Windows suggests doing constantly, but I don't think that's the problem because I have internet on all my other wireless devices (Phone, PS3, Xbox).I am able to see the router most times and connect to it, but I am unable to connect to the internet, the networking image in the bottom corner has a yellow warning sign. Also, after a certain amount of time, the wireless card is unable to detect any wireless signal, the networking image in the bottom corner has a red X through it. I disabled all networking interfaces besides the wireless card because of an error message that I thought may have been caused by it: "This computer is continuously switching between two or more wireless access points or routers", but disabling the other interfaces did nothing and the message still appears after troubleshooting.
View 1 Replies View RelatedI have the firmware 2.10NA. In my home we have about 4 laptops and 4 smartphones connecting to this router wirelessly and 3 of the laptops often lose connection for hours. We have tried unplugging the router and plugging it in again and factory reset and also resetting it through the IP address but the connection doesnt come back. Recently it has gone out for about 3 hours now. Also the wireless LED icon on the router constantly blinks is this normal? On the laptops where theres no connection it says limited connectivity. Is it possible that there is too many devices connected to the router or something. or could this be a problem with the laptops and not the router?
View 6 Replies View RelatedAbout six months ago I replaced my old router (some generic 802.11b/g router I got for free with a rebate years ago and which lasted a few years) with a Dir-601 after the old router started intermittently cutting out. Setup of the Dir-601 was straightforward enough and I have WEP enabled. Both my Macbook and my wife's Macbook can connect fine if we choose the router from the drop-down wireless network list, and the router has been consistently reliable in maintaining a connection as long as the OS is running.
HOWEVER, neither computer will remember the wi-fi network and won't auto-connect when waking up from sleep or after a restart. Our iPhone and Android smartphones remember the network just fine and auto-connect every time, zero issues. I've gone through all the typical Mac troubleshooting steps, deleting saved network connections and re-establishing new ones. Never solves the problem. We always have to go to the wireless network menu and manually select the wifi connection to connect to.
It's not the Macbooks. Firstly, both macbooks have the same issue, and they're each running different MacOS versions, so there's no version-specific issue that can be at play here. Secondly, neither macbook had this issue with any previous wifi router. Thirdly, anywhere else we take our macbooks where we've set up a wifi connection, they remember it and auto-connect without us having to manually select the network. The only network where we have to manually select the network every time is the one set up with the Dir-601. In fact, we're at my inlaws for the holidays and our Macbooks have been auto-connecting to their router each and every time.Is there a setting I'm not seeing on the Dir-601 admin page?
Region : Portugal
Model : TL-MR3040
Hardware Version : V1
Firmware Version : TL-MR3040_V1_120822
ISP : Optimus Kanguru (LTE) www.kanguru.pt
I have a modem huawei E392u-12 from the service provider optimus kanguru, url..., and i would like to use my usb modem with this router i have. the router identify the modem but does not conect. i have seen that the bin files available are just for vodafone and TMN, what can i do so i dont have to buy another equipment.
Region : Others
Model : TL-MR3040
Firmware Version: 3.14.4 Build 121017 Rel.62268n
I have purchased TL-MR3040 especial for share my 3G account . I have connect it by ethernet port and made setups and it is in 3g/4g only mode. In system checks my modem indicated as " Identified" the modem is a Huawei E160E . My notebook and tablet connects by wireless connection to TL-MR3040 but the router does not dial ISP number *99# . The led on usb modem continues flashing. the 3G modem works perfectly with my notebook and tablet and I use the same parameters for TL-MR3040 with tablet. But most of the parameters don't exist on setup pages of TL-MR3040 . [code]
I just got my DIR 825. It had 2.02NA Firmware in it. It had a few options that I wanted to use but didn't work. So I thought I would update firmware. I follow the instruction from dlink to install firmware. So I loaded 2.03 and noticed internet connection not working. So then I loaded 2.05 part1 and part2. Still could get internet connection to work but the reason to upgrade the option I wanted worked. So then I loaded 2.06 and still same result. No internet connection. So then I loaded the original firmware back in and internet connection works. Why doesn't the internet work on the other firmware updates. I got the updates from dlink website. I would like to update firmware
View 9 Replies View RelatedMy desktop doesnt connect to internet, but my internet works fine wid wi-fi systems like mobiles and tabs. IE/Chrome/Firefox all have the same prob. But when I remove the ethernet connection, shut down and then start my system and then connect the lan, all the 3 browsers work fine. I'm noticing this issue after I've uninstalled TuneUP Utilities trial pack and/or after I've installed LABTEC wireless Keyboard and mouse. Later on I've uninstalled the LABTEC software, but still its no use.
View 3 Replies View RelatedOn my laptop, the wireless will show, "currently connected to my router", yet it says below, "there is no internet connection"...I have already replaced my router and modem recently..still no change...I'll reset the router and i'll have internet access for 30 minutes and it will log me off.
View 2 Replies View RelatedMy Belkin wireless usb network adapter isn't connecting to the internet. The router and everything is fine as other computers in the house are working. It's just one desktop pc that isn't connecting.Our internet was running slower than it should and that was because we had too many wires and so in order to speed it up we decided to use a wireless connection instead of an ethernet cable.The problem seems to be that the adapter just isn't connecting. The little icon showing the status of the connection keeps going back and forth from no connection to attempting to connect.
View 14 Replies View RelatedMy desktop doesn't connect to the router and when i troubleshoot, it tells me that the ethernet cable is not plugges into the computer. But the ethernet cable is already plugged in. My two laptops have no problems connecting to the internet.
View 7 Replies View RelatedI have a TP-Link TL-WN723 USB WiFi adapter attached to my laptop, which runs WinXP Service Pack 3. It successfully detdcts the WiFi provided by my Edimax BR62-04Wg router, but when I try to connect, it cannot obtain an IP address and cannot connect to the network.
- The very same WiFi adapter can connect to other routers without any problem
- Any other device can connect to the very same network provided by my router without any problem
- Using the WiFi adapter with other computers does not work
Thus, it seems that the problem is somewhere between this specific router and WiFi adapter. Here is an interesting detail though:If I try connecting to my WiFi while a LAN cable from the router is plugged into my computer, the wireless connection establishes too. Even if I later unplug the LAN cable, the wireless connection continues to work. But it won't establish the connection without the cable plugged in.Here's what I've already know/tried:
- Rebooting the PC
- Re-installing the WiFi adapter's drivers
- All drivers and firmwares are the newest available
- Re-starting and reconfiguring the router
- Using the Windows client for wireless networking and the client included on the WiFi adapter's CD
- Changing the router's connection type to any available option: Access Point, Station Ad-hoc, AP Bridge WDS
None of these had any effect except for one:
- When I changed the router's connection type to Station Ad-hoc, I could connect wirelessly even without the LAN cable plugged in, and I had Internet access. However, in this case, other devices, such as smartphones could not detect the WiFi connection.
I recently bough a belkin router (Share N300) but it just wont connect to the internet.My setup is as follows:ADSL -> Modem -> Router -> PCThe internet works fine when I connect it directly to my PC (via the modem), and other PCs too.So no issue of MAC address lockdown.I've tried connecting through static mode with the data from ipconfig /all, but it still doesn't work.I've even installed DD WRT and Tomato to no avail.
View 2 Replies View RelatedToday, suddenly my internet went down so I checked up on it and I found out that something might be wrong with my router. I can connect just fine if I connect my computer with the modem directly but when I plug the modem to the router, I can connect to the router but it doesn't give me any internet.
View 9 Replies View RelatedMy computer doesn't want to connect to the internet via ethernet, however it will connect via wireless to the same network. Other computers on this network connect to the internet just fine.
View 3 Replies View RelatedI'm running Vista on my Desktop, and the router is a Gigaset SE567/8 Series. Whenever I turn my computer on, it will connect to the network, but not to the internet. I get the caution symbol in the task bar with the network icon, and it show the "identifying ( mySSID )". I have to unplug the router for 30 seconds in order to make it work correctly. This router was just installed by my ISP the other day and its been acting this way since then.
View 1 Replies View RelatedI have a Motorola Docis Surfboard model Model SB6120 and can connect to the internet with the ethernet cable directly onto the labtop but if I connect it to the E4200 router the range is there but the internet connection is not. This happened 2 days ago and can't get the router to work.
View 4 Replies View RelatedI basically plugged it into my Verizon Fios router and downloaded the Cisco Connect application (since I have a macbook air which has no CD drive)
It sets up fine, I change my router name.... BUT at the end it says there is an issue of some sort. The Cisco Connect application reloads saying "repairing connection" but then does not repair it.
Not sure where to go from here. I also logged in to 192.168.1.1 but of course I do not know where to go from here. I also reset the router trying to start from new, but no dice.
My router was working till date. Due to some reason, I disconnected the internet cable and connected it. After that it does not connect to internet.Based on the forum I accessed 192.168.1.1, it displays the administration page. I have reset to factory settings and switched off the router for a while and turned it
View 9 Replies View RelatedI don't really know much about computers, but I have a Dell inspiron 1545 and it fell off my bed by accident a while back so now I notice glitches here and there, but recently it just doesn't connect to Internet anymore, and I know my wifi is fine because I'm using my iPad right now to write this. When I go to Network and Sharing Center it shows a drawing of my PC and then a green line to "Identifying" and a line with an X to Internet. It also says my access is local only.
View 3 Replies View RelatedI have an Acer AM3100 desktop running Windows Vista. It is connected to a netgear wireless router via an ethernet cable. I also have two laptops connected to the same router. The laptops connect to the internet fine but the desktop doesn't. I connected to the internet fine (satellite) before I moved but won't connect now. Norton 360 can update automatically and Skype connects but I can't open web pages. I used the norton tool and uninstalled Norton 360 but it still won't connect. I'm attaching the ipconfig information.
Windows IP Configuration
Host Name . . . . . . . . . . . . : Kids-PC
Primary Dns Suffix . . . . . . . :
[Code]....
I recently installed a NetGear router to my PC in order to do online gaming. Now my laptop does not connect to the internet. I have spent over 9 hours on the phone with Centurylink (the internet provider); Netgear (the router) and HP (the laptop). Each one says its not their problem. The laptop can find our connection, it says "Connected". However it then says "Internet access denied".
View 5 Replies View RelatedIm trying to bridge my zyxel eq660r-f1 dsl modem so that i can resolve the nat issue im having in my home network. Only problem is that everytime I bridge the modem and hook my E4200 up, I cannot connect to the internet. If i connect my laptop directly to the modem, I do get internet but not through the router itself.
View 8 Replies View RelatedMy WRT54G2 v1 does not automatically connect to the internet on computer start-up. The computer will say "Connected, No Internet Access" In order to fix it I have to unplug the router and then plug it back in. This happens to any computer that tries to get online from a cold start-up. The router must always be unplugged, then plugged back in, then it will have internet access (and will generally maintain it throughout the session and even if the computer is restarted, i.e. warm boot). I have downloaded the latest firmware uprade.
View 9 Replies View RelatedIn my device I am able to browse through & connect to my HOME wifi network ; But after connecting it says 'No Internet Access'.I tried connecting with my SONY Bluray , iphone , ipad , laptops -- everywhere same story.I am able to plug in the ethernet cable directly from modem & able to connect to network.I am not able to open the http://192.168.0.1 -- ( When I am plugged in the modem directly)
Following are my router details
FCCID - KA2DIR601A1
IC : 4216A-IR601
H/W Ver:A1
F.W Ver:1.00 NA
some problems I was having with the wireless schedule forcing a router reset when the schedule was enabled. D-Link eventually conceded that the problm is a faulty router. However, to have the router replaced will take 2 - 3 weeks, meaning I have to buy another router if I don't want to be offline for that long. So I've decided to save up my money to buy a new modem, and I've found that by having wireless enabled at all times works around the problem.However, around the same time I started diagnosing that problem I was changing various settings. At the time I may not have mentioned I have 2 PS3's here. These stopped being able to connect to the internet at around that time, and the kids tell me they didn't tell me about it because they knew I was working on other router problems, but now they want their PS3's to work on line so they can play online games.I have tried automatic configuration and manual configuration. I have the MAC addresses in the router, have set them up in the Network filters, and have a DHCP reservations. I have used the routers DNS and also tried OpenDNS addresses.I keep getting error 80710102 (DNS error), and when I first turn on a PS3 807101FF. Both PS3s exhibit the same symptoms.
View 2 Replies View RelatedI have a simple(?) problem with my old router. I had this for 2 years but I never used it till today. So its brand new, just without warranty . Long story short, this router can't connect to internet. I tried resetting the router, newest firmware, stock firmware, chaining the Ethernet wire, etc. Nothing would work. The weird thing is, I can connect to the router both wirelessly and through the Ethernet port, but the router can't "communicate" with my Netgear cg3000d. I used the wizard to set it up.
View 4 Replies View RelatedI have a DIR-600. but now, it can not connect to internet.this is images when i connect mordem internet with Dir600. (mordem running good)And when i connect my laptop with Dir600?
View 1 Replies View RelatedI can't connect to the internet. I connect the cables but the router doesn't connect to the internet. I contacted to my ISP and they told me to put this settings but I don't know how to put these
Settings;
Type: Bridge
Encapsulation: LLC
VPI: 8
VCI: 35
QoS: UBR
Modulation: GDMT
I recently bought this router and I've set the router too many times and keeps doing the same thing. I've used WPA WEP and without security and the same the router still dosen't want to connect to the internet.
View 10 Replies View RelatedI'm having troubles getting my router to work today for some reason. I'm with teksavvy and I've had the router for 6 months now and this is the first time I'm having problems connecting to the internet.
Any laptops or desktops in the house that connect wirelessly cannot load anything related to the internet. If they are connected by an ethernet cable then only skype works for some odd reason. When I connect directly to the modem with my desktop it works perfectly. I tried unplugging the router for 5 minutes many times and that hasn't worked. I've tried power cycling through it as well, modem -> router -> computer and it does not work. I've also tried resetting the router as well, holding the reset button for 20 seconds. During the setup, the router could not detect an internet connection. After the setup it was the same situation as I started with. None of the computers can connect via router.
