D-Link DIR-655 :: Cannot See Wireless Device From Windows 7 Explorer
Aug 25, 2011
My Samsung phone is working as it should as an USB device (using KEIS and such). However though it receives ip address from DIR-655 router and is registered by MAC address in router - also possible to ping its IP from windows I cannot see it in /Network from my WIN7 64bit OS? The desktop comp is wired to the router, phone is on wireless.
I ve tried several settings and almost had it. It did work some months ago...
From log; "SSID": Wireless system with MAC address XXXXXX secured and linked" (That is my mobile phone)
View 14 Replies
ADVERTISEMENT
May 4, 2012
I replaced my D-link router with a new EA4500 last night.I can get to the internet, I set up 2 computers wirelessly, I set up a printer wirelessly.I am struggling with the NAS.I have a D-link DNS-323 which was previously connected to the D-link router via ethernet cable and worked fine.The Cisco Connect software does NOT have the ability to "connect" an ethernet-connected device, only USB or wireless.Windows Explorer does not see the DNS.The DNS- 323 has a fixed IP address which I know. I type it into my browser and it can't find it.I have shut down the DNS and unplugged the power for a full reset.I am running Win 7 Ultimate on my PC.
View 4 Replies
View Related
Oct 9, 2011
Problems have arisen since purchasing a new laptop with Windows 7. The problem seems erratic. The laptop connects to file servers on the network, but often cannot connect to the network. If it connects, often connection is lost when clicking to a new page.Usual error message: "Windows can't communicate with the device or resource (primary DNS server)"Network map shows communication lost between ADSL and network.Direct Hard wire connection to internet through ADSL works without issue. Hardwire connection through DIR-655 same as wireless: erratic, error messages. This message posted from another wireless router, specifics not known, connected without issue, on-line for 3 hours without problems.
-IP address: no difference between using automatically obtained or assigned IP address
-DNS server: no difference between using automatically obtained or assigned IP address
Router setup numerous times using CD ROM set up program.Firmware updated to the most recent version.Gone to tech support several times; can get the PC to connect and once done, tech support says its working only to disconnect within a few minutes.What must I do to get this DIR-655 router working on a regular basis?
View 7 Replies
View Related
Apr 20, 2012
I have this test windows 2008 r2 server. I can connect to the internet on this server.However my client xp machine, cannot see the server via windows explorer. I can however ping the windows 2008 r2 server. Using the servers ip of 192.168.1.230 Another thing is I cannot also remote to the server on the internal LAN. Using RDP.I ve even tried with firewalls turned off on the server for some mins.
View 1 Replies
View Related
Aug 17, 2011
I am new to this forum. I ve been googling for CCNA explorer for last one month. All the versions that i download is not compatible with windows 7 and works fine with windows XP. Does anyone know if cisco has released any new version that is compatible with Windows 7?
View 6 Replies
View Related
Apr 13, 2012
I have some issues with win 7 64 bit pro. I have 3 computers on a cat 5 wired home LAN using a DGL-4500 router and in yhe same homegroup. All are gigabit capable. 2 are regular PCs, one is an HTPC. All have the latest drivers.1) File transfers never exceed 12% of the network capacity.2) If I transfer from computer A to computer B's public folder, I can transfer 1GB in a few minutes. However, if I attempt to copy/paste a file from Computer B's public folder to computer A, computer A takes forever "discovering" the file, then gives some absurd transfer time, say 11 hours for the same file.3) If however I go to computer B and paste the same file into Computer A's public folder, the transfer takes only a few minutes.
4) If at any point during scenario #2 I right-click B's public folder from A during a transfer, I get the spinning circle forever which 90% of the time results in Explorer hanging and requiring the process to be killed/restarted.
View 4 Replies
View Related
Nov 28, 2012
I have a small mixed peer-to-peer network comprising 2 Win7 PCs, an iMac and a Win7 laptop and 2 little file servers: a Netgear Stora and a LaCie-2big.Stora is correctly listed under the Network part of Windows Explorer, but LaCie isn't, although I have been able to map a drive to a share on LaCie.No problem accessing files etc.Why would the LaCie not be displayed in the Explorer file tree?
View 2 Replies
View Related
Feb 5, 2011
I connected to a hotspot that is available for Me to connect to. I connected to one, then I went to the little bars to make sure it's actually connected, It says "Internet Access" (Windows 7) Which means it's connected. Then I clicked on Internet Explorer, to go on the Internet, and It says.. "Internet Explorer cannot display the webpage" Then I clicked on "Diagnose Connection problem" It started to detect the problem.. When it was finished it said.. "Website (Yahoo!) is online but isn't responding to connection attempts."
I went to Tools, Internet Options, LAN Settings, and I checked the First two boxes. Where it says "Address" I put in [URL]then I went back, and went on the Internet but It still says ---"Internet Explorer cannot display the webpage" Then I went back to Tools, Internet Options, and took off [URL]then tried again, then I went back to the Internet but it still said the same thing saying-----"Internet Explorer cannot display the webpage" Then I clicked on "Diagnose Connection problem" and it ---started detecting the problem.. and when it was finished detecting it said...---"Windows could not automatically detect this network's proxy settings."
You only want "Automatically detect settings" checked. The second check box if for a configuration script or the like to setup IE settings. That is really only used by company's that want specific home pages and other settings set to match their networks.If anything is checking in the "Proxy Server" area, I would uncheck it as you won't go through a proxy since you are connecting to a hotspot. It is pretty rare for public locations to use proxy servers.I connected to a hotspot that is available for Me to connect to. I connected to one, then I went to the little bars to make sure it's actually connected, It says "Internet Access" (Windows7) Which means it's connected. Then I clicked on Internet Explorer, to go on the Internet, and It says.. "Internet Explorer cannot display the webpage" Then I clicked on "Diagnose Connection problem" It started to detect the problem.. When it was finished it said.. "Website (Yahoo!) is online but isn't responding to connection attempts."
View 14 Replies
View Related
Nov 2, 2011
I have 2 desktops and a laptop accessing a wireless Motorola modem using roadrunner broadband. My desktop/Vista and laptop/Windows 7 are working fine. My older desktop with XP has a wireless card and shows that the wireless is connected with great signal strength but won't access Internet Explorer. I keep getting an error message. I have tried re-setting up the wireless and shutting down the machine ,etc. I have seen a few older posts that suggest downloading some software, etc
View 1 Replies
View Related
Sep 23, 2012
Client connects to PIX 501 but cannot see the LAN in Windows Explorer.Devices can be pinged by IP and hostname (netbios name)I can navagate to a server by typing in \servername.Why can I not get a resolution from Cisco techs? [code]
View 1 Replies
View Related
Apr 11, 2011
is there any way of getting the DCS-2121 cameras to register as a windows "video" device? I am running windows 7 and would like to use the remote cam as a video device in a desktop app - Microsoft OCS.
View 1 Replies
View Related
Jun 4, 2012
Since some days we have a ASA5510, we connected it on a Windows Vista Laptop via ethernet cable (using at the back of the router the mgtm slot) and connect it on the network slot on the laptop. Laptop is getting IP addresses automatically.
Now we tried to reach the router in the Internet Explorer using: http://192.168.1.1, but we could not reach this site. When I try to ping the router via cmd and typing ping 192.168.1.1 I get answers.
For us it is very important to change the IP address of the router, as he will be used in a network with 10.xxx.xxx.xx addresses.
View 2 Replies
View Related
Sep 13, 2012
after installing xp my wireless card doesnt show in device manager
View 8 Replies
View Related
Apr 27, 2011
Dell Wireless 1390 WLAN MiniCard on my Inspiron 1521 with WINDOWS 7 does not show in the device manager. There is a popup window that says Driver blocked due to incompatibility.Ive tried to install new drivers but it doesn't work.
View 3 Replies
View Related
Feb 16, 2013
I recently upgraded my Wi-Fi router to an EA3500 and am controlling it using Smart Wi-Fi running on a wired Windows 7 machine.So far, I have been able to add devices to the network without issue and each of those connections works fine. All, except my TV, have been Windows 7 based machines. Smart Wi-Fi Device List has been able to "see" each device and I have been able to add them to that list as well.
I am attempting to add a Windows 8 desktop computer to the network which is using a external USB wireless adapter. That computer can see and connect to the network through the EA3500 and the connection seems to work fine. The only issue is that its adapter does not show up in the Device List.
1) Does the Device List do anything else besides showing a list of devices I chosen to add to my network?
2) How do I get my Windows 8 wireless adapter to show up in the Device List?
View 6 Replies
View Related
Dec 26, 2012
Region : Austria
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
unfortunately I've lost my device pin and I've reset my device.can I get the device pin on a other way? on my invoice there is no information about that.
View 1 Replies
View Related
Feb 21, 2013
How do i stop a Wireless device from connecting to the router? i attempted to find an answer myself and failed
View 1 Replies
View Related
Aug 10, 2010
set up the wireless network at a friend's house, which is a large solid-brick house that winds from one end to the other. The current location of where the cable comes into the house is unfortunately on the far-left end of the house, which means that the right end of the house receives no signal from their DIR-825 wireless N router.
What I've been looking into is the best way to wirelessly extend the wireless signal to the other end of the house. It seems straightforward enough to use an ethernet cable and access point to extend a wireless network, but that is not really a good option for this house. After reading many forum posts (and not being an expert myself) it seems like it may be possible to wirelessly extend the wireless network with another router, although it appeared that this is much less common (if at all possible) with wireless N routers.
what device I need to accomplish what I've described above? Another router, or some kind of access point/bridge? I saw at least one rather expensive wireless N repeater online (a Hawking brand, I believe) but was hoping to avoid that option initially, but if that is the only way to go then so be it :-)
View 12 Replies
View Related
Jun 8, 2011
I can send email though my yahoo account (which is hard wired to my router) and I can access the internet through my wireless device (iPhone 3GS) but I can not send email through my wirless device. I keep getting a message stating it can't reach the smtp server.
View 1 Replies
View Related
Jan 6, 2013
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmwar Version :
ISP : AT&T
I recently got a new modem from AT&T. I hooked it up and everything worked fine for a few days. Last night some friends came over with their wireless devices (iphone, ipad) and after a while, the internet got really slow. Then it was unresponsive but it said that we were still connected to the network. So I decided to restart the router. Once it was finished rebooting, we were not even able to connect to the network at all. Even on my computer downstairs I was not able to connect wirelessly. I am connected via ethernet from the router right now on my computer upstairs and that is working fine. I have tried rebooting the router to factory settings, unplugging the modem, rebooting the modem, unplugging the modem, changing the router settings, pretty much every practical solution for simple connectivity issues.
View 1 Replies
View Related
Nov 20, 2011
I have a DIR-655 Rev B, in a typical cascaded config: modem > dir-555 > switches & devices, etc.One of the four dir-655 ports is connected to a cheap-o Belink Wifi router which I use as an access point (I only use this because there's one device that only supports WEP). I was debugging a WiFi issue and I pulled the plug on this Belkin just to get it out of the picture. Well, when I did that, EVERYTHING that was connected through the DIR-655 lost connection. (Well, all the wired stuff anyway- not sure about WiFi devices through the DIR-655). I noticed that the port link light for the powered-off device stayed on on the DIR-655. When I unplugged the cable from the DIR-655, everything went back to normal.
So what I'm trying to figure out now is, is this a DIR-655 issue, or is it something screwy with the Belkin? Or Both? I've got to assume that there's some inherent flaw in the DIR-655 that allows something connected to a port to screw up everything that it's hosting.
View 7 Replies
View Related
Dec 8, 2012
-Model : TL-WR1043ND
-Hardware Version : v1
-Firmware Version : 120605
I'm wondering if USB HDD spin down capability does exist on the deviceI think this enhancement will be serve a lot of costumers who wish to use all USB features.
View 1 Replies
View Related
Jan 23, 2013
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.17 Build 120426 Rel.29216n
ISP :
In the absence of true QoS capability on the 4300, what is the best way to give bandwidth priority to one of my network devices?
I have an Apple Airport Extreme connected to my network. It is used to stream music from my Ipod to my sound system. I do this through my network (rather then connecting the IPod directly to the AE) so that I can connect to radio stations over the internet. The problem is that I'm getting random dropouts (pauses in streaming). I've shut down everything on the IPod to make sure that there are no Apps competing for WIFI resources. The dropouts happen even if there is little activity on the network (e.g., file downloads, youtube, etc.)
What I want to do is to get the 4300 to give top priority to the AE. How can I do this without QoS capability? Can I allocate more bandwidth to the AE when it is receiving streaming data?
Note: The AE is always connected to the network. It uses DHCP to get it's IP address. It is connected to the 5G band. Signal strength is typically 1 to 2 of 3 bars (average is 1.5 bars). The 2.4G band has a slightly higher signal strength but the same dropouts occur so the problem does not appear to be signal strength.
View 1 Replies
View Related
Feb 20, 2013
Region : Singapore
Model : TL-WR941ND
Hardware Version : V3
I would like to connect a device (dataloger that sends data to a remote server via internet) which only has LAN port to a wireless network on the location. I managed to do this once with WA901ND configured in Client mode (WA901ND acts like a wireless card for this data loger).Does WR941ND support this feature (which feature should I use?) or should I buy WA901ND again?
View 7 Replies
View Related
Apr 28, 2013
Region : Others
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.31 Build 130319 Rel.57876n
ISP : Antel
I have a WDR4300 which works perfect with all devices in my house, but in my personal notebook (samsung 530U4B) wireless transfer speed is very slow in 2.4 GHz mode. 5.0 ghz works fine. I've tried everything, but I can not get good performance. at this moment I have to use a 741nd working with my wdr4300 in wds mode to use 2.4 ghz band properly.
View 6 Replies
View Related
Aug 1, 2011
A few hours ago internet explorer and Safari were connecting , as was chrome, but now only chrome connects, why is that ? how do i fix it.
View 2 Replies
View Related
Oct 21, 2012
can't access internet,searchqu.com/431 this message comes up and i can't get rid of it!
View 1 Replies
View Related
Jan 7, 2013
Region : NewZealand
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
I've plugged in a USB flash drive and enabled shared storage on my TL-WR1043ND router. With "Access shared storage with password" unticked, I can access the share using both my Windows 7 Laptop and Motorola Defy+ (with ES File explorer) and successfully play any Music off of the network share using the Android App, ES File explorer.
If I enable "Access shared storage with password" and attempt to log in using any of the user accounts I've set up on the device, I will be able to access the shares using the credentials on my Windows 7 Machine, but not with my Motorola Defy+, instead I will simply receive "Login failure". I'm Picking it has something to do with the network share type?
View 4 Replies
View Related
Nov 18, 2012
Region : Italy
Model : TD-W8960N
Hardware Version : V4
Firmware Version : 67406
ISP :
I have problem on router td-w8960n v4 internet speed download is limited a 4 mb in device android e ios wifi connected for test i use application speedtest.net on ipad 3 and samsung galaxy s
View 2 Replies
View Related
Apr 9, 2013
Region : Australia
Model : TD-W8950ND
Hardware Version : V1
Firmware Version : 1.2.9 build 110212 Rel.22296n
I made some changes on my wireless modem router to stop dhcp and dns provided by my device. A server is now doing it, but at the same time I appear to have connection issues where I didn't before. In an attempt to resolve the issues I looked at the System Log and a number of things were coming up that concerned me. These are as follows:
-user: tr69c: Unable to retrieve attributes in scratch PAD
-user: Stored Parameter Attribute data is corrupt or missing
Additionally I'm getting a lot of kernel: Intrusion alerts which I can't determine how serious they are. Where to start tracking down these issues (if they even warrant investigation).
View 1 Replies
View Related
May 17, 2011
I had some viruses/malware that I was able to kill using skill.com freeware. Ever since, I have had no internet conectivity although signal is excellent. [code]
View 11 Replies
View Related
Jul 9, 2012
This is 1st attempt at home networking:win xp pro to win 7 ultimate.can get both devices to ping and receive both by ip address and computer name.both devices seen in each others workgroup view. cannot open either device from the other device.file and printer sharing is on on both machines.
View 1 Replies
View Related
Feb 22, 2012
Windows cant communicate with the device or resource(primary dns server). The device or resource is not responding to requests.
View 4 Replies
View Related
